1. Car driving test
1.01 Introduction
This chapter sets out the background and basic requirements of practical driving tests. It also gives detailed guidance on conducting tests. The digital test report (DTR) is an electronic recording mechanism on an iPad and is used for the full end-to-end journey from the journal to in-car to back-in-office administration.
1.02 Responsibilities of examiner on test
The examiner is present during the test to evaluate the candidate’s ability to drive. This involves identifying mistakes, which the candidate may make.
The examiner is not legally in charge of the vehicle during the test (though they are responsible for the conduct of the test), nor are they supervising the candidate during the test: Regulations do not require a driver to be accompanied by a supervisor when taking a test. This law applies to all practical tests including lorries carrying a load for the purposes of the test (the load being the responsibility of the candidate and trainer/accompanying driver).
Examiners should not, therefore, intervene except when it becomes necessary to do so in the interests of public safety, including their own and that of the candidate. Such intervention may be by warning, advice or by operation of the controls. If a candidate is in difficulties and clearly suffering from nervousness, the examiner should offer a few words of reassurance to help them settle down.
1.03 Test control
Driving tests must be conducted in accordance with regulations and procedures and in accordance with instructions laid down by the Chief Driving Examiner.
Going off route, or needing reminders of where to go, are not in themselves faults.
Tests should not be terminated because a candidate is struggling to understand independent driving instructions.
Examiners should employ their experience, knowledge, and judgement where necessary to curtail the independent section and issue normal directions.
This action should be necessary only in exceptional circumstances.
The control of the test throughout, including the independent driving section, is extremely important.
1.04 Car driving test requirements
Driving tests are conducted in accordance with the provisions of the Motor Vehicles (Driving Licences) Regulations 1999 (as amended). The test requirements are set out below:
- eyesight
- vehicle safety checks
- set exercises (one of the following):
- reverse parking (either into a bay or on the road)
- forward parking (into a bay)
- pull up on the right and reverse in a straight line
- controlled stop (angle start)
- 1 normal stop
- hill start/designated stop
- a minimum of 30 minutes of driving, which includes independent driving
- emergency stop - carried out in 1 of every 7 tests
1.05 Test candidates
Test candidates must demonstrate competence in their ability to complete the test, without danger to and with due consideration for other road users, the following:
Preparation to drive:
- adjust the seat as necessary to obtain a correct seated position
- Adjust rear-view mirrors and seat belt
- check that the doors are closed
Technical control of the vehicle:
- start the engine
- move off smoothly when going ahead, at an angle, and on a gradient (where possible)
- accelerate to a suitable speed while maintaining a straight course, including during gear-changes
- adjust speed to negotiate left or right turns at junctions, possibly in restricted spaces, while maintaining control of the vehicle
- brake accurately to a stop where directed, if need be, by performing an emergency stop
- carry out a controlled stop by pulling up in a designated position
Carry out one of the following manoeuvres:
- park the vehicle (parallel or in a parking bay forward or in reverse)
- pull up on the right and reverse in a straight line
Behaviour in traffic:
- observe (including the use of rear-view mirrors) road markings, and signs, and react appropriately to potential or actual risks
- communicate with other road users using the authorised means
- comply with road traffic regulations and any instruction given by police and/or traffic controllers
- drive with the vehicle correctly positioned on the road, adjusting speed to traffic conditions and the line of the road
- keep the right distance between vehicles
- change lanes
- pass parked or stationary vehicles and obstacles
- approach and cross junctions
- turn right or left at junctions
- join or leave the carriageway
Where the opportunity arises:
- pass oncoming vehicles, including in confined spaces
- overtake in various situations
- approach and cross level-crossings
1.06 Minimum test time requirements
It is important that, unless the test is terminated, minimum driving times are strictly adhered to. Regulations state that the time during which a person is required to drive on the road for a category B car test is not less than 30 minutes. For extended tests, this is not less than 60 minutes of driving time.
In the case of category B (car) tests, the minimum driving time is measured from when the vehicle starts moving at the beginning of the test to when the engine is stopped at the conclusion of the test. Therefore, manoeuvres carried out in the DTC car park count towards the minimum time period. However, as already stated, when taking into account all DVSA’s requirements the total test time will last between 38 and 40 minutes. For tests conducted using the digital test report, a stopwatch timer is available if the examiner chooses.
Despite correct use of a well-constructed route, occasionally a candidate, because of their ability, experience, and favourable traffic conditions, will be able to get round the test route more quickly than is normal. In these exceptional circumstances, examiners are reminded that it is still vital that the on-road minimum time requirement and the total time of between 38 and 40 minutes are adhered to. Therefore, to comply with DVSA’s requirements, examiners should consider modifying the route to avoid returning to the test centre too early. Alternatively, if examiners are aware of any hazards on routes, i.e., road works that would knowingly cause a delay, these areas should be avoided. It is not acceptable to deliberately use unsuitable routes at busier times in order to return late and cause cancellations.
Time management is part of the ‘control’ of the test. Providing all legal requirements have been met, the examiner should consider modifying the route if a candidate drives excessively slowly or hesitantly and a serious fault has been recorded. It is not acceptable to follow a full route if this is clearly going to cause such a late return that the next test would have to be cancelled. Any deviation from the route or other action taken to comply with the requirement should be recorded in the additional comments section on the digital test report.
The LDTM is responsible for ensuring that all routes are sufficiently long enough to ensure that route(s) are not extended on a regular basis. Therefore, routes should only need to be modified/extended in exceptional circumstances, as mentioned above.
1.07 Car minimum test vehicles requirement (MTV)
The driving test regulations require a candidate to provide a suitable vehicle for the purposes of the test. This means that the vehicle must be roadworthy, taxed, insured, and of such construction or design as to enable the examiner to properly conduct the appropriate test.
Examiners are advised to exercise considered judgement and discretion so that no candidate whose test could reasonably be conducted is turned away.
Category B vehicles must be fitted with a passenger seatbelt, passenger integral head restraint (slip-on types are not acceptable), and an internal mirror for the use of the examiner. A vehicle fitted with any pedal, lever, or other device, which could allow the accelerator to be operated by someone other than the driver, must be removed or rendered inoperable.
Any vehicle in which the examiner rides must allow a clear all-round view of the road.
1.08 General competence to drive
The object of the test is to ensure that the candidate is well-grounded in the basic principles of safe driving and is sufficiently practised in them to be able to show, at the time of the test, that they are a competent and considerate driver and are not a source of danger to themselves or to other road users.
Examiners should remember that, in most cases, candidates will be novices and will have had only limited driving experience; and will have been accompanied by a professional instructor or other tutor. It would, therefore, be unreasonable to expect them to demonstrate the degree of skill and road sense of a seasoned driver. The same might apply to an international driver from another country whose experience of driving in this country may be limited.
It must also be appreciated that many candidates will also be more nervous during the driving test than when driving with their instructor or with a friend. A pleasant outgoing approach, not only in the waiting room and on the way to the vehicle, but throughout the test is particularly important to help candidates to relax.
1.09 Completion of the digital test report
When using the digital test report, it is specific to the candidate and test category. The digital journal contains further information relating to the candidate. This information can be accessed by selecting the candidate’s name on the journal. This must be done if there is a yellow exclamation marker next to the candidate’s name, ensuring the examiner is aware of any relevant information prior to the test.
Completing the digital test report:
- eyesight test: Select Pass or Fail following the eyesight test. If Fail is recorded, the app will direct the examiner to the end of the test page.
- tell me question: Select the ‘Tell Me’ question asked at the beginning of the test.
- vehicle registration: Insert vehicle registration.
- automatic transmission: Select the appropriate box if the vehicle has automatic transmission; this will be verified later in the app.
- instructor’s information: Record the instructor’s personal reference number from the instructor’s certificate/licence displayed on the vehicle’s windscreen, if available.
- vehicle ownership: Record if the vehicle belongs to a driving school and whether dual controls are fitted.
- accompanying test personnel: If an ADI, DVSA manager, sign language interpreter, or other observer accompanies the test, the appropriate box/boxes should be recorded.
1.10 Definitions of recorded faults on digital test report – cars
Record completion of:
- normal stop, angled start, and hill start/designated stop
- manoeuvres
- reverse right:
- control: incorrect use of controls and/or inaccuracy
- observation: lack of effective all-round observation
- reverse park (road/car park):
- control: Incorrect use of controls and/or inaccuracy
- observation: lack of effective all-round observation
- forward park:
- control: incorrect use of controls/inaccuracy
- observation: lack of effective all-round observations
- eco-safe (fuel efficient) driving: not part of pass/fail criteria
- control: starting/moving off, accelerator use, gears
- planning: hazard awareness, planning and anticipation, engine braking
- vehicle checks:
- incorrect answer and/or demonstration of safety check questions
- controlled stop:
- slow reaction, inadequate braking, loss of control
- ETA (examiner took action): verbal/physical (e.g. dual controls/steering)
- control:
- accelerator: uncontrolled or harsh use
- clutch: uncontrolled use
- gears: Failure to engage appropriate gear for road and traffic conditions. Coasting in neutral or with clutch pedal depressed
- footbrake: late and/or harsh use
- parking brake: failure to apply or release correctly and when necessary
- steering: erratic steering, overshooting the correct turning point when turning right or left, both hands off steering wheel, or hitting the kerb
- Note: control faults should not be marked in this section if committed during a manoeuvre
- precautions: failure to take proper precautions before starting the engine
- ancillary controls: failure to use ancillary controls when necessary
- move off:
- safely: failure to take effective observation before moving off, including correct use of signals
- under control: inability to move off smoothly, straight ahead, at an angle, or on a gradient
- use of mirror(s): failure to make effective use of the mirrors well before:
- signalling
- changing direction
- changing speed
- signals:
- necessary: signal omitted
- correctly: incorrect or misleading signal. Failure to cancel direction indicators
- properly timed: signal incorrectly timed so it is either misleading or too late to be of value
- junctions:
- approach speed: approaching junctions at a proper speed, either too fast or too slow, for whatever reason
- observations: not taking effective observation before emerging
- turning right: late or incorrect positioning before turning right, including failing to move forward into the correct position to turn right at traffic lights
- turning left: positioning too close or too far from the kerb before turning left
- cutting corners: cutting right-hand corners, particularly where the view is limited
- judgement:
- overtaking: attempting to overtake unsafely or cutting in after overtaking
- meeting: failure to show proper judgement when meeting approaching traffic
- crossing traffic: turning right across the path of oncoming traffic
- positioning:
- normal driving: incorrect positioning during normal driving, including cutting across the normal road position when going ahead at roundabouts without lane markings
- lane discipline: failure to maintain proper lane discipline at roundabouts with lane markings when going ahead and when continuing to drive ahead in designated lanes
- pedestrian crossings:
- failure to give precedence to pedestrians on a pedestrian crossing
- non-compliance with lights at pedestrian controlled crossings
- position/normal stops:
- normal stop: not made in a safe position
- awareness/planning:
- failure to judge what other road users are going to do and react accordingly
- clearance/obstructions:
- not allowing adequate clearance when passing parked vehicles and other obstructions
- following distance:
- keep a proper and safe distance from the vehicle in front when moving
- leave a reasonable gap from the vehicle in front when stopping in lines of traffic
- use of speed:
- driving too fast for road, traffic, and weather conditions
- progress:
- appropriate speed: driving too slowly for road and traffic conditions
- undue hesitation: being over-cautious by stopping or waiting when it is safe and normal to proceed
- response to signs/signals: failure to comply with or late reaction to:
- traffic signs: inappropriate response
- road markings: for example, double white lines, box junctions, lane direction arrows
- traffic lights: including failure to move off on green when correct and safe to do so
- traffic controllers: signals given by a police officer, traffic warden, school crossing warden, or other persons directing traffic
- other road users: failure to take appropriate action on signals given by other road users
1.11 Preparations for the test
The examiner should take the following on test:
- digital device – iPad
- paper contingency test report - PTR
- pass certificate book - DVSA10
If the route to be used involves an independent section delivered by means of following Satnav directions, examiners should take a Satnav, preloaded with all test routes, and relevant peripherals, i.e., dash mat, external power supply, cables, dual 12v adapter, and carry bag.
1.12 Meeting the candidate
The examiner should ask for the candidate by their full name, greet them pleasantly, and:
- ask the candidate for their driving licence (and if not a photocard licence, then a valid passport) and their theory test (TT) pass certificate (if applicable)
- compare the driving licence number with the information on the digital test report
- ask the candidate to read, confirm, and sign the insurance & residency declaration on the digital test report
Note: Candidates who present for an extended test do not have to satisfy the residency requirement. Compare the signature on the photocard licence with the signature on the digital test report. Compare the photograph on the photographic identity document against the candidate. If you have concerns that the person in the photograph is not the correct person, you may consider that it is a suspected candidate impersonation. Examiners should follow the guidance on checking candidate identity in the DT1 document library.
Candidates will have to present either:
- a valid signed UK or EU community photocard licence*
- an old-style valid signed UK, Northern Ireland, or EU community paper driving licence; and a valid passport
- a valid signed Northern Ireland photocard licence and paper counterpart
- a theory test certificate if taken in Northern Ireland
*Some first-time licences issued by DVLA to young people have had identity verification through the Passport Office. These photocard licences are issued without a signature and are acceptable at test, subject to all other normal checks as described in this paragraph. Issue Numbers on licences are no longer relevant.
The candidate must confirm whether they would like their end-of-test summary sent to the email address they provided during booking, an alternative email address, or by post. Ask the candidate if they would like their instructor/accompanying driver to accompany them on test.
1.13 Eyesight
Read in good daylight (with the aid of glasses or contact lenses if worn) a registration mark fixed to a motor vehicle and containing letters and figures 79 millimetres high and 50 millimetres wide at a distance of 20 metres.
1.14 Vehicle safety checks
Answer vehicle safety check questions.
1.15 Direction indicators and stop lamps
Before entering the vehicle, the examiner should visually check direction indicators and stop lamps. If this reveals any obvious damage that raises doubts about whether they are operational, the examiner should assist the candidate in making a practical check and ask them to operate the appropriate control. If the suspect item does not function satisfactorily, the candidate should be allowed to rectify the fault. If this cannot be done within a reasonable timeframe and may potentially impact any subsequent tests, the test should be terminated. To avoid subsequent argument, the candidate should be asked if they wish to confirm by personal observation that the particular item does not function satisfactorily, in which case the examiner should operate the control.
In deciding whether direction indicators and stop lamps are in an acceptable condition for the test, examiners should be guided by the principle that no candidate should be turned away whose test could reasonably be conducted; for example, if both obligatory stop lamps are working but the high-level light is not, the test must proceed.
Compliance with the law
Apart from making a visual check of indicators and stop lamps, examiners are not required to make a thorough check of candidates’ vehicles. It is accepted, however, that it would be unreasonable to expect an examiner to continue with a test if they notice or have drawn to their attention, anything about the vehicle that would make it illegal or unsafe for use on the road, or which would clearly constitute a risk to the health or safety of the examiner.
Examiners should exercise their considered judgment and discretion so that no candidate whose test could reasonably be conducted is turned away.
1.16 ‘L’ (or ‘D’) plates in Wales
Regulations require the vehicle to display ‘L’ or ‘D’ plates, that are clearly visible from the front and rear of the vehicle.
1.17 Examiner’s door and seating
The examiner must sit in the front passenger seat of the vehicle, as this is the best position from which to observe the candidate’s performance. Before moving away, the candidate may check that the front passenger door is properly closed or locked. This is usually done to show the examiner that they are aware of the safety precautions to take before moving off. Examiners should not indicate that this precaution is other than a proper one for any driver to take.
Cars presented for the test must be fitted with a passenger seatbelt, passenger head restraint, and an interior mirror for the examiner’s use. A spare stick-on interior mirror should be kept at the driving test centre.
1.18 Seat belt, head restraint, and mirror
Before starting the drive, the examiner should ensure that their seat, seatbelt, and head restraint are adjusted correctly to ensure safety and comfort. Examiners should also ensure they are sitting comfortably and in a stable position to support themselves in the event of sudden braking or a collision.
The additional mirrors fitted for the examiner’s use should be adjusted so they have a view to the rear. Mirrors must not be moved by an examiner unless they are positioned in a way that obstructs the examiner’s clear vision of the road ahead. If additional mirrors have to be moved, they should be positioned as close to the upper part of the screen as possible; this reduces the likelihood of interference with airbag deployment. Additional mirrors should not be placed below the driver’s mirror, as this could cause a blind spot and obstruct the driver’s view.
Note: it is not a legal requirement that the head restraint is adjustable, but the passenger seat head restraint must be fitted as an integral part of the seat. ‘Slip-on’ type head restraints are not permissible.
1.19 ADI and PDI certificates – recording numbers
ADI Number
If an ADI or PDI certificate is displayed in the windscreen or the instructor identifies themselves to the examiner and indicates that they wish the candidate to be linked to their name, then the instructor number from the certificate should be entered on the digital test report. If the candidate, using their own car for the test, presents their instructor’s certificate number, it should be entered on the digital test report.
Note: Data Protection Act. If the instructor certificate is not displayed, then the number must not be entered on the digital test report, and neither the candidate nor accompanying driver should be questioned about the identity of the instructor.
PDI certificates
These have two PRNs (personal reference numbers). Care should be taken to record the Potential Driving Instructors’ number and not their ADIs number who is providing the PDIs training.
1.20 Pre-brief
Examiners should take the opportunity on the way to the car or before moving off, to briefly explain to the candidate what will happen on the test.
1.21 Instructions to candidates
Examiners should ensure their instructions are absolutely clear. Candidates must not be left in doubt about the route to be taken. Directions should be given in good time, especially where marking of traffic lanes indicates an option. At complex junctions and gyratory systems, a request simply to turn right or left may not be enough to indicate the route clearly.
Candidates should not be given any grounds to complain of being flustered or uncertain. If you are aware a candidate has dyslexia or dyspraxia, you should tactfully establish if it affects their driving and if any adjustments are necessary. This may include confirming directions by pointing or using hand signals.
1.22 Independent driving briefing
It is important that the candidate is left in no doubt about what is required in the independent driving section of the test. There are two methods of independent driving, following directions given by a Satnav or following traffic signs. The examiner should pull the candidate up on the left and clearly brief the method required. If you are aware a candidate has dyslexia or dyspraxia and you have established it affects their driving, choose an independent driving section that is best suited to their needs.
1.23 Start of drive
The drive should start without any instruction from the examiner except to indicate the immediate route to be taken.
1.24 Starting the engine
The candidate should ensure that the handbrake is applied and the gear lever/selector is in neutral before starting the engine.
1.25 Moving off
The examiner should observe whether the candidate first sees to the front, then to the rear, ensuring the way is clear for pulling out, gives the appropriate signal if necessary, and moves away smoothly and safely. Wherever possible, the ability to move off on a reasonably steep uphill gradient should be tested.
A candidate starting on a gradient should be capable of paying attention to other traffic as well as moving their vehicle away without rollback and/or excessive engine revolutions. If stopping on a hill is not possible, an additional designated stop must be conducted. The test must always include moving off at an angle from behind a stationary vehicle.
1.26 Emergency stop
An emergency stop exercise should be conducted in 1 out of every 7 driving tests.
This is to ensure that as a road safety critical exercise, it continues to be taught.
Identifiable patterns (times, routes, and so on) should be avoided so that a random aspect of emergency stop selection is retained.
1.27 Manoeuvring exercises
The candidate will be asked to carry out two set exercises: one controlled stop and one of the following, which may be selected at random:
The reverse parking exercise
The reverse park exercise can be conducted either into a parking bay in the DTC car park or on the road. Examiners have flexibility in making a choice of which manoeuvre to use (Pull up on the Right, Forward Park or Reverse Park) provided that each manoeuvre is used equally over a period of time.
Reverse park at the start of the test - car park
The size and layout of the car park may restrict the options available to the candidate. Examiners should allow the candidate to reverse into any bay of their choice, and no attempt should be made by the examiner to determine or dictate which bay is used or how the candidate carries out the exercise.
At the start of the test, after the pre-brief, the candidate should be told that before going on to the road, they are to carry out the reverse park exercise into a convenient bay. They should be asked to drive out of the bay to the left or right (if both options are available in that car park) and stop with the wheels straight before reversing into any convenient bay and parking the car. Examiners should not instruct candidates to park in the centre of the bay. The instruction is to prevent them reversing back into the bay on the same lock.
Providing some attempt has been made to straighten the front wheels, examiners should not be concerned if the wheels are not completely straight. The candidate may elect to drive forward to adjust the angle at which they address the bay they intend to reverse into, or space permitting, they are allowed to drive forwards into one bay before reversing back in a straight line into the opposing bay. Once the exercise is completed, the candidate can be given the instructions for following directions around the route.
Reverse park at the end of the test - car park
On the approach to the centre, the candidate should be advised to turn into the car park and reverse into any convenient bay to park the car. The candidate can again make their own choice of bay and carry out the manoeuvre in the way that they choose, given the restrictions that may be imposed by the characteristics of the car park. Candidates should park within a bay, but examiners should not be too concerned, when making their assessment, of the final position of the car in the bay. Parking outside the bay is unacceptable. Candidates should not normally be penalised for crossing the lines when entering the bay. Examiners should consider whether the car could reasonably be left, in that car park in the prevailing conditions, in that position. Exceptionally, the examiner may feel the need to leave the car before making an assessment. This is acceptable provided the candidate is asked to secure the car and stop the engine.
Irrespective of the presence of other vehicles or pedestrians, the candidate should be expected to take all round observations to ensure that the manoeuvre is executed safely. The question is not whether there is anybody there, but whether the candidate has taken adequate observations to ensure that safety is maintained throughout the exercise. Observation should be assessed as though the exercise was carried out on the road. At some DTCs, to avoid congestion, it will be necessary for some examiners to carry out the exercise at the start of the test and some at the end. The exercise may be completed into any empty marked bay, irrespective of whether cars occupy the adjacent bays, provided that these vehicles do not encroach on the bay to be used.
Reverse park - road
The candidate should be asked to pull up well before a parked vehicle identified by the examiner. They should then be asked to drive alongside it and reverse into a parked position either:
- behind one parked car, when the exercise should be completed within two car lengths
- between two parked cars, where the gap should be equal to about two car lengths.
Drivers of vans or other small commercial vehicles are expected to do this exercise in exactly the same way as a car driver. Vehicles parked on the offside of the road should not be used. The candidate should show proper care for the safety of other road users while reversing. If, because of the examiner’s seating position, the candidate has difficulty in taking observation, examiners should be prepared to adjust their seating position during the reversing exercises.
Forward park
The forward park exercise should be conducted into a parking bay in a car park along the test route, without the need to deviate too far from the route. The examiner will direct the candidate to a suitable area of the car park, which is not too busy and will not interfere with customers and car park owners / operators. There is no requirement to carry out this exercise between two cars. In exceptional circumstances, and depending on the layout of the car park, this can be carried out at the DTC, providing the manoeuvre can be conducted by steering into a parking bay, then reversing out to the left or right and driving forward into another area of the car park. If test centres are close to each other, this manoeuvre can be carried out in neighbouring test centre car parks, providing the conduct of the manoeuvre is not compromised.
Whilst being directed around the car park, the candidate should be advised to drive forwards into any convenient bay, finishing within the lines, either to the right or the left (if car park allows). The candidate can make their own choice of bay and carry out the manoeuvre in the way that they choose, given the restrictions that may be imposed by the characteristics of the car park. The candidate should then be asked to reverse out to the right or left (if car park allows). If there are one-way systems in operation, the examiner should dictate which direction the candidate is required to reverse in.
The size and layout of the car park may restrict the options available to the candidate. Examiners should make no attempt to determine or dictate which bay is used or how the candidate carries out the exercise. If the car park is too busy or no bays are available or suitable, the examiner should direct the candidate out of the car park.
Candidates should park within a bay, but examiners should not be too concerned, when making their assessment, of the final position of the car in the bay. Parking outside the bay is unacceptable. Candidates should not normally be penalised for crossing the lines when entering the bay. Examiners should consider whether the car could reasonably be left, in that car park in the prevailing conditions, in that position. Exceptionally, the examiner may feel the need to leave the car before making an assessment. This is acceptable provided the candidate is asked to secure the car and stop the engine.
Irrespective of the presence of other vehicles or pedestrians, the candidate should be expected to take all-round observations to ensure that the manoeuvre is executed safely. The question is not whether there is anybody there, but whether the candidate has taken adequate observations to ensure that safety is maintained throughout the exercise.
Reverse right
This manoeuvre should be carried out during routine driving, on a general main road which would normally carry light to medium traffic flow, therefore it is not necessary to deviate from the test route, into a side road or housing estate. It is not always necessary for the candidate to encounter traffic whilst completing this manoeuvre however carrying this out on busy roads or busy times of day, should be avoided due to the excessive length of time it would take to complete the exercise. The chosen road should allow the candidate plenty of opportunity to pull up on the right on a straight section of road with clear visibility well ahead and behind.
Whilst driving on a suitable road, and at a safe location, the candidate should be asked to pull up on the right when it is safe to do so. Once stationary, the candidate should then be asked to reverse for two car lengths before being asked to drive on again. If the candidates begin to select a location which is not suitable, then the exercise should be aborted before moving across to the right and attempted later in the test.
The candidate should show proper care for the safety of other road users while pulling across to the right, reversing and moving off.
Should the candidate ask the examiner to assist when reversing or moving off to re-join their side of the road, they should be informed that the purpose of the test is to prove their competence to drive without the help of a supervisor, and that they should carry out the exercise as if they were unaccompanied.
The examiner must not get out of the vehicle to direct or assist the candidate.
If a vehicle pulls in front of the candidate prior to the completion of the exercise, the examiner should take control of the situation and advise the candidate to reverse back further to allow a clear view ahead. If a vehicle blocks the candidate from reversing, the manoeuvre should be aborted and a manoeuvre attempted later in the test. If this situation causes the candidate’s view to be severely restricted, then the examiner should offer some assistance.
The manoeuvre ends once the candidate has stopped reversing and selected neutral.
1.28 Reaction to traffic signs and signals
The examiner should be satisfied the candidate reacts promptly and correctly to traffic signals and signs and to signals given by the police, authorised traffic controllers and other road users.
The candidate should be fully aware of their responsibilities at pedestrian crossings, and act accordingly.
1.29 Methods of signalling
Candidates normally signal by direction indicator but may, if they wish, additionally signal by arm. Signals should be assessed on whether necessary and appropriate signals are given in good time, and indicators cancelled afterwards.
In the case of a disabled driver, it will usually be apparent whether they are physically capable of signalling by indicator and arm. However, if the examiner can only satisfy himself about this by observing the candidate giving signals whilst actually driving, they should specifically ask the candidate to signal by indicator or arm as appropriate, but only for as long as is necessary to determine whether or not they should be restricted to driving vehicles fitted with direction indicators and stop lamps.
1.30 Road junctions
The examiner should observe whether the candidate has the vehicle under proper control and in the appropriate gear, takes account of the type of junction, road signs and following traffic, gives any necessary and appropriate signals in good time, and keeps the vehicle correctly positioned throughout. The examiner should also note whether the candidate takes adequate and effective observation before entering the intersection, and that they do so with due regard for other road users.
The route should still include some urban roads which will allow the examiner to observe the candidate’s reaction to crossing intersections during general driving. A driver who is over-cautious at a main road may act differently at a junction of less important roads.
1.31 Overtaking, meeting and crossing
The examiner should observe the candidate’s actions in overtaking and meeting other vehicles, and crossing the path of other traffic when they are turning to the right. Before overtaking, the mirror(s) should be used to observe following traffic, and appropriate signals given if necessary. While showing consideration for other traffic, the candidate should not give way unduly when it would be safe and proper to proceed. On the other hand, they should not be inconsiderate, e.g. by turning right in the face of closely approaching traffic.
1.32 Normal stops
A minimum of two normal stops should be made during the test.
Normal stops during independent driving
A normal stop may be included when pulling up to start the independent drive section, providing the road conditions allow and the correct wordings are used. Candidates may be asked to carry out a normal stop once they have begun driving independently.
1.33 Fuel efficient driving
Fuel-efficient driving is a recognised and proven style of driving. It contributes to road safety while reducing fuel consumption and emissions which reflects the increased awareness and need for economical / environmentally friendly driving.
Fuel efficient driving does not contribute to the result of the test.
The Eco-safe driving boxes on the digital test report are used to record an assessment of the driver’s ability to drive with economy and the environment in mind. The assessment of fuel-efficient driving is taken over the whole test, not focussing on one instance - candidates only need to display knowledge of fuel-efficient principles they are not expected to be experts. A candidate may sacrifice fuel efficient driving techniques so as not to compromise safety. This should always be carefully considered in the assessment process.
There are two fuel efficient headings: control and planning. The following examples do not cover the whole range of fuel-efficient driving styles and are for guidance only.
Control
Changing down to lower gears when the road speed is too high is not considered an ‘fuel efficient driving’ technique. It uses fuel unnecessarily, as does needless harsh acceleration and using the higher rev range between upward gear changes. Doing so is a waste of fuel with no gain in safety or performance.
A driver should understand the capabilities of his/her vehicle and should be able to take advantage of the power/torque characteristics of the engine by utilising the highest gear possible without causing the engine to labour. The ability to utilise a lower ‘rev’ range should ensure that fuel is not being used unnecessarily and therefore fewer pollutants will be released through the exhaust system.
Planning
Needlessly stopping then moving away from rest has a detrimental effect on fuel consumption. An Eco-safe driver will keep the vehicle on the move whenever and wherever it is safe to do so.
Driving more fuel-efficiently starts by scanning the road ahead and anticipating traffic flow. It’s important to look out for traffic lights, signs, road markings, and potential hazards well in advance. This allows the driver to adjust speed smoothly, rather than making sudden stops or accelerations. By being proactive and planning the drive, the driver can maintain a steady speed and reduce unnecessary fuel consumption.
The alternative of not using this technique is to brake late, which uses more fuel and is not a demonstration of effective fuel-efficient driving principles.
In the previous examples, if the candidate demonstrates safe driving procedures by not committing control or procedural faults, then no fault should be recorded under another heading other than in ‘Eco-safe Driving’.
Whether the result of the test is a pass or a fail, if an Eco-safe fault has been recorded in either one or both boxes the examiner should de-brief the candidate in the normal way.
1.34 End of test
At the end of the practical driving test the examiner should advise the candidate of the test result. A fail result should be conveyed sympathetically.
The examiner’s decision is final and cannot be changed. If a candidate questions the test decision, they should be referred to the end of test summary for more information.
1.35 Pass certificate – DVSA 10
DVSA10s should be completed in black ink.
Rubber name stamps must not be used on a DVSA10 certificate. DVSA10s are accountable documents and are issued against an examiner’s signature. They must be safeguarded at all times.
Provided the examiner doesn’t work out of their `home’ zone, they can use any of the books of pass certificates issued from any test centre in that area. If an examiner is working on detached duty in another zone, they should draw DVSA10s from the DTC and return them to the DTC on completion of the detached duty.
1.36 Issuing of DVSA10
The examiner should ask the candidate for their licence or other documentation and copy the name & driver number details direct to the DVSA10. The driver number should be copied exactly as shown even if the examiner suspects it is incorrect, e.g. the first 5 letters do not match those of the candidate’s surname.
In the case of a Northern Ireland licence, the number should be copied exactly as shown - starting from the left - and a line put through the remaining empty boxes.
The DVSA10 certificate should be completed in the following order:
- title - Mr/Mrs/Miss/Ms etc
- forename, and second forename if any in full and initial(s) of any other forename(s)
- driver number
- appropriate category
- strike out whether vehicle used was automatic
- whether an extended test
- restriction code (if appropriate)
- test date in numeric form, e.g. dd/mm/yyyy
- name of test centre
- signature/name of examiner
- applicant’s signature and date (if appropriate - non ADLI route)
- documentation at end of test
1.37 Issuing pass on DTR
The provisional licence received section of the digital test report must be completed for all tests. Care must be taken to ensure accuracy.
1.38 Automated driving licence issue
Eligible ADLI candidates
With the exception of motorcycle module 1, ADI part 2 or 3 and driver CPC module 4 - all practical test pass results are automatically sent to DVLA. Those candidates who hold a GB or registered with DVLA EU/EEA photocard licence can have their new licence sent to them.
Eligible candidates are asked if they wish to have their licence to be sent to them automatically. The digital test report includes an identifier for DVLA so that they know when to issue a new licence automatically or wait for further information.
An EU member state photocard licence can now be used for the ADLI route. The GB Driver Number can be obtained from the examiner’s journal.
Candidates are not eligible to use the ADLI if they:
- refuse to sign the medical declaration
- hold a Northern Ireland or community licence (all NI licences have an 8 number driving licence number).
- have had a change in their personal details (domestic and EU/EEA licences)
- have presented a licence without a signature
- have changed their address from that which is on the photocard licence
- have a paper licence
- are scheduled to take a Driver CPC practical demonstration test within near future
- have just passed a Driver CPC practical demonstration test
- have just passed a motorcycle module 1 test
Candidates who are not eligible to use the ADLI route or do not wish their licence to be issued automatically must have their licence returned to them.
The examiner should give the candidate the DVSA10 certificate and advise the candidate they will receive an end of test summary.
1.39 Fail
For digital test reports, the provisional licence issued is not required. In the case of failure, the examiner should: de-brief the candidate and advise them they will receive an end of test summary.
1.40 De-brief
At the end of a test the examiner should offer the candidate a brief explanation of the faults marked on the digital test report. This de-brief should aim to give the candidate an overview of their driving. If a candidate fails on an accumulation of more than 15 driving faults, then all the faults need explaining.
If the instructor/trainer/accompanying driver is present for the decision & de-brief, the examiner should ask: ‘would you like your (instructor/trainer/accompanying driver) to be present for the conclusion of the test?’ If the instructor/trainer/accompanying driver is not present the question should not be asked.
If any observer (other than another DVSA examiner) who has accompanied the test remains present for the end of test feedback, then the debrief witnessed should be recorded on the digital test report. (If the observer does not remain for the feedback, then ‘No’ should be recorded on the digital test report).
If at any time the instructor/trainer/accompanying driver comes over to the vehicle to listen to the conclusion of the test, and a de-brief is to be given, the examiner must ask the candidate whether they want their instructor/trainer/accompanying driver present - consequently if they do attend for the feedback then ‘Yes’ should be recorded on the digital test report.
If the candidate elects not to have their instructor/accompanying driver present for the decision & de-brief, then the examiner should ensure that the candidate’s request is complied with.
If a candidate’s performance has been of a very poor standard involving a multitude of serious or dangerous faults, the examiner should use discretion and explain only the most serious faults.
If in exceptional circumstances, an examiner decides not to give an explanation, full reasons for the decision should be noted in the additional comments section of the digital test report.
Where a candidate refuses the de-brief, the examiner should give their opinion as to why, or any explanation given by the candidate, in the additional comments section of the digital test report.
If the candidate wants to discuss the test in greater detail, it should be explained that examiners are not permitted to do this. However, to be helpful, the examiner should suggest that their comments about the items marked or contained within the end of test summary be relayed (by the candidate) to their instructor, who should be able to provide the detail required.
If a candidate argues or becomes abusive, or so upset that an explanation is obviously of no value, the examiner should abandon the attempt and a brief note should be made on the digital test report.
1.41 Driving test report
The digital test report comprises a digital journal, containing all of the information relevant to the candidate and their test booking along with a digital test report relating to their completed practical test.
1.42 Completion of DTR at the end of the test
The route number must be recorded.
Method of independent driving must be recorded.
If the candidate’s appearance is a true likeness of the licence photo, this must be recorded. Distinguishing features should also be recorded, and additional information recorded if candidate appearance was different to the licence photo. Examiners should ensure that any description is factual and cannot be misconstrued as being in any way offensive.
Photocard or Passport must be recorded.
Show Me question asked must be recorded.
The appropriate weather condition(s) must be recorded.
In additional information the name of any DVSA staff member accompanying the test should be recorded. It is not necessary to record the name of an ADI / accompanying driver or candidate’s friend.
After failed tests, details which may be useful in dealing with any enquiry or complaint, should be recorded, for example:
- the details of any serious or dangerous fault recorded on the test report
- notes of variations from standard controls
- any unusual behaviour or comment by the candidate
- any other special feature of the test, such as the vehicle being in a car park and causing difficulty before the test started.
Plain words should be used with no abbreviations. After passed tests, any unusual incidents or circumstances that occurred should be recorded. Followed by the examiner’s signature in the box provided, if a paper contingency form is being used.
2. Motorcycle test
2.01 General information
Modular test
The motorcycle test is in two modules.
Candidates have two years from the date they passed their multiple choice and hazard perception test to complete both Module 1 and Module 2 of the motorcycle test.
Candidates must use the same subcategory of machine for both modules of the test.
Candidates must always have a valid theory test certificate before taking their first motorcycle practical test.
Unless candidates take the progressive access route, they must have a valid theory test certificate before taking any further practical motorcycle tests.
A confirmation letter issued by DVSA is acceptable if the candidate has lost their theory test pass certificate.
To avoid a test being terminated unnecessarily and with time permitting, examiners should contact the Examiner Hotline to verify a Theory Test pass.
If Deployment can provide the required information, then the test can be conducted.
If a candidate has not passed both modules within the two-year period they are required to re-take and pass the theory test and to re-take and pass Module 1 of their motorcycle test before they may take Module 2.
The two-year period will then recommence from the date of the new theory test.
Candidates must present a valid CBT certificate when they take both Module 1 and Module 2 of the motorcycle test, candidates who hold full motorcycle entitlement do not require a CBT certificate and are exempt from this requirement.
If a candidate’s CBT certificate expires, they may retake it at any time.
If the CBT certificate is presented, the certificate number should be entered on the Candidate Declaration page of the digital test report.
Note: A valid Northern Ireland CBT certificate is acceptable.
Motorcycle minimum test vehicles (MTV)
The driving test regulations require a candidate to provide a suitable motorcycle for the purposes of the test.
This means that the motorcycle must be roadworthy, taxed, insured and of such construction or design as to enable the examiner to properly conduct the appropriate test.
The motorcycle must be reasonably representative of type.
Speedometers must be in either mph or mph/kph. Vehicles which have been changed mechanically from km/h to mph are acceptable for test; the face of the speedometer must show mph or mph/km/h, external overlays are not acceptable.
The introduction of modular testing requires candidates to use the same sub-category of motorcycle for both modules of the practical test.
The requirements for motorcycle minimum test vehicles (MTV) are as follows:
Category AM: two wheeled moped, no more than 50cc and below 4kW with a maximum design speed of no more than 28 mph (45km/h). (Since June 2003, all type approved mopeds have met this rule). All two wheeled AM machines can be used on test unless there’s clear evidence that they don’t meet the requirements.
Category A1: a two wheeled motorcycle without a sidecar, between 120cc and 125cc capacity with an engine power no more than 11 kilowatts (kW) - 14.6 brake horsepower (bhp) and be capable of at least 55 mph (90km/h). All machines between 120 and 125 cc can be used on test unless there’s clear evidence that they don’t meet the requirements.
Category A2: solo motorcycle at least 245cc capacity with an engine power between 20kW (27bhp) and 35kW (46.6bhp) and have a power to weight ratio of no more than 0.2kW per kilogram. If fitted with a restrictor kit, it must not be derived from a motorcycle of more than double its power.
Category A: solo motorcycle at least 595cc capacity and have an engine power of at least 50kW (67 bhp) and a minimum kerb weight of 180kg.
Electric motorcycles may be used on test providing they meet the MTV power requirements for the relevant subcategory, this is measured by their continuous power rating and quoted in kW.
Normally only disabled riders may use a motor-tricycle or motorcycle and side car for their test.
However, some 3-wheeled machines are classed as mopeds or motorcycles.
These are machines which have the overall characteristics of a solo motorcycle and where the distance measured between the centre of the area of contact with the road surface of any two wheels is less than 460 millimetres they are classed as motorcycles.
Providing they meet all other MTV requirements these motorcycles can be used by any rider for their practical motorcycle tests or CBT training.
Where three wheeled motorcycles are fitted with a device or locking mechanism to prevent them from leaning or tilting this must be in the unlocked position for both Mod1 and Mod2.
For category A2 & A DVSA will accept evidence from manufacturers or official importers that a specific model of motorcycle meets these requirements and will publish this information where it applies to a number of machines of a specific type.
Examiners should refer to the most recent version of the official motorcycle MTV list - this can be found on SharePoint.
For machines not on this list or where an individual machine has been restricted to comply with the minimum test vehicle requirements it will be accepted for test providing certified proof of compliance or restriction is available for the examiner.
This must be a certificate or on headed paper from an official source such as a main dealer, official importer, or recognised specialist in restricting vehicles. Dyno certificates alone are not acceptable.
Restricted A2 machines
Proof of the restriction must be on headed notepaper, showing the registration number, from a main dealer, an official importer, or a recognised specialist.
Any switchable engine control unit (ECU) or variable power restriction device must be clearly visible showing the power it’s set to (an ECU under the seat is acceptable if it is easily accessible).
Interchangeable carburettor heads, exhaust manifold restrictors or a hidden ECU are not suitable methods of restricting a bike that can be switched between two categories but may be used as a permanent certified restriction.
A dyno test certificate will not be accepted in isolation as proof.
Examiner journals
Examiners will receive their daily journal on the digital test report.
Further details of the candidate can be accessed by selecting their name.
Digital test report
The digital test report is specific to the candidate and the test category.
The digital journal contains further information relating to the candidate and can be accessed by selecting the candidate’s name on the journal.
This must be selected if there is a yellow exclamation marker next to the candidate’s name, so the examiner is aware of any relevant information prior to the test.
The motorcycle test is in two modules and a candidate must use the same sub-category of machine for both modules.
It is therefore very important that examiners ensure the licence sub-category that is on the digital test report and the pass certificate match the motorcycle presented for test.
The appropriate category AM, A1, A2 or A must be inserted on the digital test report.
If the candidate has used a machine fitted with automatic or semi-automatic transmission the relevant box on the digital test report should be marked.
The appropriate category A, A1, A2 or AM should be entered on the DVSA12 Module 1 pass certificate.
Licence and entitlement checks
Check the candidate’s ID in line with the instructions in Chapter One.
Provisional driving licences just show category A start and finish dates, encompassing all motorcycle subcategories. Therefore, it is acceptable if a candidate attends for a category A1 or A2 test when their provisional driving licence shows category A.
Examiners must check a candidate’s entitlement carefully. This is particularly important for Module 2 when the examiner must check that the sub-category of machine on the Module 1 pass certificate is the same as the vehicle presented for the Module 2 test.
Motorcycle examiners must check the candidate’s age from their driver number to make sure they are old enough to ride the machine presented for the test.
The age restrictions are:
- A1: at least 17 years old
- A2: at least 19 years old
- A: at least 24 years old*
*Unless the rider has held an A2 licence for at least 2 years, in which case they must be at least 21 years old.
Following disqualification from riding under the Road Traffic Act, or revocation under the Road Traffic (New Drivers) Act 1995, all riders are required to complete CBT to validate their new provisional driving licence when it is issued. This applies in all cases, including those where the person previously held full motorcycle entitlement. A DL196 issued prior to the disqualification period is invalidated by the disqualification.
If a rider has previously been disqualified, the examiner will need to contact the examiner hotline to check the date of issue of the licence. Providing the DL196 is issued after the re-issue of the licence, the test can be undertaken. If the DL196 is dated before the date of issue of the licence, the test cannot be taken.
Riders who have had their licence revoked under the New Drivers Act will not have a revocation shown on their licence. These riders are still required to re-take CBT and present a valid CBT certificate (DL196) at the test.
If having made all appropriate checks a candidate’s entitlement cannot be established, the test will not be able to proceed.
Upgrading an entitlement
Candidates who hold a full motorcycle entitlement, gained by passing both theory and practical tests, who wish to upgrade their entitlement before the two-year progressive access period is up will have to complete both modules on the larger category machine.
They will have six months from the date of passing Module 1 to pass Module 2.
These candidates are not required to re-take their CBT certificate, but they must have a valid theory test pass certificate.
A valid theory test pass certificate is not required if the candidate is just upgrading to remove restriction code 78 (restricted to vehicles with automatic transmission) on the same category of machine.
Candidates who are following the progressive access route (from 2015 onwards) will not require a CBT or theory test pass certificate.
They will have six months from the date of passing Module 1 to pass Module 2.
2.02 Module 1
Module 1 preliminaries
This Module begins with the normal identity and entitlement checks. The candidate is required to sign the insurance and residency declarations and confirm their email address for the end of test summary.
The candidate must produce the following valid documents:
- a photocard driving licence or a paper licence and current passport
- DL 196 CBT certificate (unless exempt)
- theory test pass certificate (unless exempt)
Photocopies or scanned images of documents are not acceptable, except the theory test pass certificate. This will be a duplicate copy issued by DVSA as a pdf, this can be printed or presented electronically, but the examiner must see the accompanying email from DVSA.
The candidate is required to sign the insurance and residency declarations and confirm their email address for the end of test summary.
Candidates must wear clothing that meets these minimum standards:
- a securely fastened motorcycle helmet that meets British or EU safety standards
- motorcycle boots that provide support and ankle protection, or sturdy trainers/shoes
- heavy denim trousers or textile or leather motorcycle trousers
- a heavy denim jacket with several layers underneath or textile or leather motorcycle jacket
- motorcycle gloves
If a candidate’s clothing doesn’t meet these standards, if it’s possible, they should be given an opportunity to borrow something that is suitable; otherwise, the test should be cancelled.
An exemption exists for followers of the Sikh religion if they are wearing a turban instead of a safety helmet.
The eyesight test is not carried out as part of the Module 1 test, it is carried out during Module 2.
Definitions of recorded faults on digital test report – Mod 1
- use of stand
- manual handling
- slalom / Figure of 8
- slow control
- ‘U’ turn exercise
- precautions
- move off
- safety
- control
- controlled stop
- emergency stop – record the speed of each attempt
- avoidance – record the speed of each attempt
- ETA
- physical
- verbal
Module 1 test requirements
Number of rider errors
To pass module 1, candidates must commit no more than five rider faults with no serious or dangerous faults.
Start procedure
At the completion of the document and identity checks, the candidate will be asked to ride the machine to the starting position.
Irrespective of where the machine is parked, the test begins when the candidate first handles the machine.
The candidate should be asked to ride front first into either the left or right-hand bay marked by green cones as shown on a diagram. The candidate may choose either bay.
General riding
Candidates who are unable to start their machines by normal means and who ask if they may push start them, should be allowed to do so.
Candidates should be asked to behave as if they were riding on the public road, which should include any necessary safety checks throughout the time they are on the manoeuvring area.
The examiner should clearly explain the exercises to the candidate, making full use of the manoeuvring board to describe the requirements and giving precise directions as to the course to be followed. It should be explained to the candidate that they should not touch any of the marker cones during the exercises.
At sites where both left and right circuits are available, examiners should ensure both circuits are used equally over a period of time.
If the candidate demonstrates a dangerous standard of riding, the examiner should assess if it is safe to continue with the test. If the test is terminated, the examiner must ensure the test report fully supports the decision to terminate the test.
Each exercise must be assessed on completion, taking into account safety and control. No more than one fault can be recorded for each exercise.
On and off stand
Candidates are required to demonstrate they can take the machine on, and off the stand safely, retaining balance and control of the machine. Candidates may choose to use either the side stand or the centre stand. A machine with no stand is not suitable for the test.
The next manoeuvre (wheeling the machine) takes place before the machine is placed back on the stand.
Wheeling the machine
Candidates are required to demonstrate they can wheel the machine safely and under control from one marked bay to another without the use of the engine. They should demonstrate effective observation during the exercise.
The candidate will be asked to wheel the machine, starting backwards, either from the left bay to the right or vice versa. They may choose to wheel the machine backwards in an arc from one bay to the other. Alternatively, they may elect to wheel the machine backwards out of the first bay before pushing it forwards and then backwards into the opposing bay.
Different techniques may be employed when wheeling the machine backwards, i.e. the candidate may hold the bar grip with one hand and place the other on the saddle or rear of the machine, they may also elect to hold the handlebars with both hands. Either technique is acceptable providing they retain safe control over the machine. Examiners should take the size of the machine and the ability of the rider into account when assessing any faults.
Paddling or sitting astride the machine to move it is not allowed other than by candidates with special needs, i.e. limited mobility, restricted leg movement. If a non-disabled candidate attempts to paddle the machine, the examiner should take control of the situation and point out that the machine should be pushed.
Slalom/figure of eight
Candidates are required to demonstrate their ability to ride the machine slowly and under control whilst turning in a restricted area; they should maintain balance throughout the exercise.
Effective rear observation should be taken before starting the exercise. When beginning the slalom exercise, candidates may elect to ride to either side of the first marker cone. The examiner should assess the actions of the candidate in the normal way. If, for instance, the candidate loses control of the machine and puts a foot down to avoid falling, then obviously a serious fault has been committed. If on the other hand, the rider dabs a foot down with a slight loss of balance and then completes the exercise without further loss of control, the fault should be assessed as a rider fault.
If the candidate misses out a cone as a result of a loss of control, then a serious fault should be assessed. If the cone is missed but the candidate’s control of the machine is correct, then the examiner may elect to allow the candidate to repeat the exercise.
Candidates sometimes ride around the yellow cone (which forms the last of the slalom exercise) as they carry out the figure of eight. This in itself is not a fault unless it is a result of poor control.
The slalom exercise will normally lead straight into the figure of eight exercise. Whilst a general awareness should be demonstrated by the candidate, there is no specific requirement for full direct rear observation before starting this manoeuvre. If the candidate stops at the end of the slalom exercise and then starts the figure of eight exercise safely, no fault should be assessed.
Slow ride
The candidate is required to demonstrate the ability to ride in a straight line without losing control of the machine. The candidate should take effective rear observation before starting the exercise.
The examiner should ask the candidate to ride slowly as if in slow-moving traffic to the blue stopping cones. A significant loss of control, for example, a total loss of balance resulting in foot down to prevent dropping the motorcycle, would be assessed as a serious or dangerous fault depending on the circumstances. Slight loss of control, such as a wobble or weave, may be assessed as not worthy or a rider fault depending on the degree.
U-turn
The candidate is required to demonstrate low-speed balance, control, and effective observation before and whilst riding a U-turn within a defined restricted space.
The candidate should be asked to ride a U-turn between the two marked lines, as if they were riding on a public road. The candidate should take effective rear observation. Touching but not crossing the lines should be regarded as a rider fault, crossing the lines would be assessed as a serious fault. A significant loss of control would be assessed as a serious or dangerous fault depending on the circumstances. If not already positioned correctly, the four blue cones that form the controlled stopping box should be re-positioned at this stage.
Cornering and controlled stop
The candidate is required to demonstrate their ability to control the machine safely as they negotiate the bend and then brake to a controlled stop in the designated stopping area. There is no minimum speed requirement for this exercise; candidates should be asked to aim to reach a speed of between 30 - 50km/h (20 - 30mph) as they pass the speed measuring equipment before braking to a controlled stop.
The candidate should stop with the front wheel spindle inside the marker cones; stopping with the spindle in line with the cones is acceptable. Stopping well short of the cones, overshooting the stopping area completely with the front wheel spindle clearly outside the cones, would result in a serious fault being assessed. Normal assessment should apply if the candidate loses control of the machine or skids.
The candidate should then be asked to turn their machine around, taking as much space as necessary so they are in position to begin the next exercise. Examiners should be ready to move the cones out of the way if this makes the turn more convenient. The first two cones (nearest the speed measuring device) should be stacked on the second two cones ready for the subsequent exercises.
Emergency stop
The minimum speed requirement for this exercise is 50km/h (about 32mph). Candidates are required to demonstrate their ability to stop as quickly and safely as possible whilst retaining control of their machine.
The examiner should stand in a safe position near the controlled stopping box where they can observe correct use of both brakes. As soon as the front wheel has passed the speed measuring device, the examiner should give the signal to stop with their right arm. Both brakes should be used effectively; however, late or no use of the rear brake could be assessed as a rider fault if the machine stops quickly and under control. Very late or ineffective use of the front brake is not acceptable even if the machine is fitted with linked brakes.
A greater stopping distance should be allowed in wet conditions.
Candidates who reach 47km/h or less will be asked to repeat the exercise providing they have not committed a serious or dangerous fault and providing their riding does not indicate it would be unsafe to continue. A rider fault will be assessed as the candidate has not achieved the minimum speed.
Candidates who fail to reach the minimum speed requirement but who achieve 48 or 49 km/h will not be asked to repeat the exercise; a rider fault will be assessed in addition to any other control or observation faults and should be recorded under ‘emergency stop’. No more than one fault can be recorded for this exercise. The examiner should record the speed of each attempt at the emergency stop exercise on the digital test report. If the candidate commits a serious or dangerous fault during the emergency stop exercise and fails to achieve the minimum speed requirement, the exercise should not be repeated. If the candidate fails to achieve the required minimum speed at both attempts, a serious fault should be recorded under the appropriate heading in item.
Candidates who do not pass the emergency stop exercise will not be permitted to carry out the avoidance exercise; the test will be ended at that point; the result of the test will be shown as a fail - not safe to continue (test activity code 4).
Avoidance exercise / controlled stop
The minimum speed requirement for this exercise is 50km/h (about 32mph).
Candidates are required to demonstrate their ability to control the machine safely whilst steering to avoid a stationary obstacle, bringing the machine to a controlled stop.
Having briefed the candidate on the exercise, examiners should stand in a safe position, away from the direction the candidate is steering towards, near the blue controlled stopping box.
Candidates who reach 47km/h or less will be asked to repeat the exercise, providing they have not committed a serious or dangerous fault and their riding does not indicate it would be unsafe to continue. A rider fault will be assessed as the candidate has not achieved the minimum speed.
Candidates who fail to reach the minimum speed requirement but who achieve 48 or 49 km/h will not be asked to repeat the exercise; a rider fault will be assessed in addition to any other control or observation faults and should be recorded under “Avoidance”. No more than one fault can be recorded for this exercise. The examiner should record the speed of each attempt at the avoidance exercise on the digital test report.
If the candidate commits a serious or dangerous fault during the avoidance exercise and fails to achieve the minimum speed requirement, the exercise should not be repeated. The examiner’s assessment should be recorded normally.
If the candidate misses the speed measuring device or fails to ride through the two blue avoidance exercise cones, the examiner should ascertain if the candidate fully understands the exercise.
If the examiner is confident a lack of understanding caused the candidate to miss the avoidance cones or the speed measuring device, then it should not be classed as an attempt and the candidate should be allowed to repeat the exercise. If the candidate didn’t carry out the avoidance exercise and in the examiner’s opinion this was not attributable to a lack of understanding, then this will be classed as an attempt, and the speed should be recorded as zero on the digital test report.
If the candidate commits a serious or dangerous fault during the avoidance exercise and fails to achieve the minimum speed requirement, the exercise should not be repeated. If the candidate fails to achieve the required minimum speed at both attempts, a serious fault should be recorded under the appropriate heading.
Having carried out the avoidance manoeuvre, the candidate completes the exercise by coming to a controlled stop between the two blue marker cones (the two furthest from the speed measuring device). One of the key competencies for the avoidance exercise is for the candidate to be able to return to their original riding line. Candidates should either have passed between the two blue cones or be in line to pass between them to be considered to have completed the exercise satisfactorily. Accuracy when stopping is not required for this exercise; however, overshooting the stopping area to a significant degree would result in a serious fault being assessed. Stopping just short of the cones is acceptable, providing the candidate does so under control. Normal assessment should apply if the candidate loses control of the machine or skids.
Module 1 pass certificate - DVSA 12
Module 1 pass certificates are numbered differently to differentiate them from Module 2 pass certificates.
As with all pass certificates, they must be completed in black ink in block capitals. The following points should assist in completing the pass certificate:
- Candidate’s name: entered normally.
- Candidate’s driver number: enter from licence.
- Theory test pass certificate number: enter from candidate’s theory test certificate.
- Date of theory test pass: enter from candidate’s theory test certificate.
- Exempt: Yes / No; ‘Yes’ if candidate is exempt from theory test as a result of holding a full licence in category A or P. ‘No’ if candidate requires valid theory test. Strike out as appropriate.
- Category: Enter category - aligned to the right.
- Automatic: ‘Yes’ / ‘No’ - strike out as appropriate.
- Extended: ‘Yes’ / ‘No’ - strike out as appropriate.
- Restriction code: Enter appropriate code if required.
- Date: Enter in DD/MM/YYYY format.
- At: Enter test centre location in text.
- Examiner’s signature, Examiner’s name: Enter as normal.
- Candidate’s signature: Candidate is required to sign Module 1 pass certificate.
Lost motorcycle Module 1 pass certificates (DVSA12)
If a candidate loses their Module 1 certificate (DVSA12), they will be able to take a Module 2 test so long as they inform the DVSA in advance, so we are able to add the relevant information regarding the module 1 pass to the examiner’s journal.
When a candidate loses their DVSA12 (Module 1) pass certificate, they should contact the customer service centre to report the loss.
The customer service representative will confirm the details of the Module 1 pass with the RSIS team in Newcastle or contact the driving examiner / LDTM from the test centre where the Module 1 test was taken so a search can be made.
A message will be placed in the ‘special needs’ field, which will appear on the examiner’s journal. The message will include confirmation that the candidate has passed their motorcycle Module 1, the pass certificate number, the motorcycle category on which the candidate took the Module 1 test, and the theory test pass date.
Message example: ‘Candidate passed Mod 1 test. Cert 1234567, Cat A DAS, TT passed 21.02.11’
If a candidate presents for a motorcycle Module 2 test without their pass certificate, but information of the pass has been provided on the examiner’s journal, they should be taken on test.
Customers who arrive without the correct documents or no information contained in the ‘special needs’ box won’t be allowed to take the test.
In circumstances where the DVSA was informed of the loss before the short notice period (3 clear working days) but no information was entered onto the journal, a free retest may be considered, and the candidate should contact the customer service unit. - If the candidate informs us within the short notice period and we are unable to add the information to the journal, no free retest will be granted
2.03 Module 2
Module 2 test requirements
Module 2 is the on-road test and consists of:
- eyesight test
- safety questions
- balance question
- a minimum of 30 minutes on-road riding, which includes 10 minutes of independent riding (the target time for module 2 is 33 - 35 minutes)
- 2 normal stops
- angled start
- hill start (if available) or designated stop if not available
Definitions of recorded faults on digital test report – Module 2
Record completion of:
- angle start, normal stop, hill start / designated stop
- ETA – verbal
- ECO – control / planning: not part of pass/fail criteria:
- control: Starting/moving off, accelerator use, gears
- planning: Hazard awareness, planning and anticipation, engine braking
- safety/balance questions: incorrect answer and/or demonstration of safety check questions
- move away:
- safety: Failure to take effective observation before moving off, including correct use of signals
- control: Inability to move off smoothly, straight ahead, at an angle, or on a gradient
- control:
- throttle: Uncontrolled or harsh use
- clutch: Uncontrolled use
- gears: failure to engage appropriate gear for road and traffic conditions. Coasting in neutral or with clutch lever pulled in
- front brake: Late and/or harsh use
- rear brake: Late and/or harsh use
- steering Balance / slow control: erratic steering, overshooting the correct turning point when turning right or left, or hitting the kerb. Loss of balance including putting a foot down to regain control of the machine
- ancillary controls: failure to use ancillary controls when necessary
- precautions: failure to take proper precautions before starting the engine
- rear observation: failure to make effective use of the mirrors well before:
- signalling
- change direction
- change speed
- signals:
- necessary: signal omitted
- correctly: incorrect or misleading signal. Failure to cancel direction indicators
- properly timed: signal incorrectly timed so it is either misleading or too late to be of value
- clearance/obstructions: not allowing adequate clearance when passing parked vehicles and other obstructions
- response to signs / signals: Failure to comply with or late reaction to:
- traffic signs: Inappropriate response
- road markings: for example, double white lines, box junctions, lane direction arrows
- traffic lights: including failure to move off on green when correct and safe to do so
- traffic controllers: signals given by a police officer, traffic warden, school crossing warden, or other persons directing traffic
- other road users: failure to take appropriate action on signals given by other road users
- use of speed: driving too fast for road, traffic, and weather conditions
- following distance: keep a proper and safe distance from the vehicle in front when moving. Leave a reasonable gap from the vehicle in front when stopping in lines of traffic
- progress:
- appropriate speed: Driving too slowly for road and traffic conditions
- undue hesitation: Being over-cautious by stopping or waiting when it is safe and normal to proceed
- junctions:
- approach speed: approaching junctions at a proper speed, either too fast or too slow, for whatever reason
- observations: not taking effective observation before emerging
- turning right: late or incorrect positioning before turning right, including failing to move forward into the correct position to turn right at traffic lights
- turning left: positioning too close or too far from the kerb before turning left
- cutting corners: cutting right-hand corners, particularly where the view is limited
- judgement:
- overtaking / filtering: attempting to overtake unsafely or cutting in after overtaking. Unsafe filtering / riding to close to vehicles/ crossing solid white line / unable to cut back in safely
- meeting: failure to show proper judgement when meeting approaching traffic
- crossing traffic: turning right across the path of oncoming traffic
- positioning:
- normal riding: incorrect positioning during normal riding, including cutting across the normal road position when going ahead at roundabouts without lane markings
- lane discipline: failure to maintain proper lane discipline at roundabouts with lane markings when going ahead and when continuing to ride ahead in designated lanes
- pedestrian crossings: failure to give precedence to pedestrians on a pedestrian crossing. Non-compliance with lights at Pedestrian Controlled crossings
- position/normal stops: not made in a safe position.
- awareness/planning: failure to judge what other road users are going to do and react accordingly
- bends: entering a bend too fast and running wide / crossing the centre line / braking harshly in the bend / to slow
Module 2 preliminaries
Module 2 begins with the normal identity and entitlement checks. The candidate must produce the following valid documents:
- photocard driving licence or a paper licence and current passport
- DL196 CBT certificate (if applicable)
- module 1 pass certificate
Photocopies or scanned images of documents are not acceptable, except for the theory test pass certificate which may be a duplicate copy issued by DVSA as a pdf and may be presented electronically.
A Module 1 pass certificate issued in Northern Ireland is acceptable, but the candidate must have their theory test pass certificate to show to the examiner. This is because the date of the theory test pass is not recorded on module 1 pass certificates issued in Northern Ireland.
Examiners must check:
- the date of the theory test passed (either from the Module 1 pass certificate or the theory test pass certificate). This must be dated on or before the date of passing Module 1
- the sub-category of machine used for Module 1 and ensure it matches the machine presented for Module 2
- the age of the candidate to ensure they are old enough to ride the category of machine used for the test
The candidate is required to sign the insurance and residency declarations and confirm their email address for the end of the test summary.
Candidates must wear clothing that meets these minimum standards:
- a securely fastened motorcycle helmet that meets British or EU safety standards
- motorcycle boots that provide support and ankle protection, or sturdy trainers/shoes
- heavy denim trousers or textile or leather motorcycle trousers
- a heavy denim jacket with several layers’ underneath or textile or leather motorcycle jacket
- motorcycle gloves
If a candidate’s clothing doesn’t meet these standards, they should be given an opportunity to borrow something suitable if possible; otherwise, the test should be cancelled.
An exemption exists for followers of the Sikh religion if they are wearing a turban instead of a safety helmet.
The candidate should be fitted with a Bluetooth radio at this point.
General competence to drive
Number of rider errors
To pass Module 2, candidates must commit no more than 10 rider faults with no serious or dangerous faults.
Road riding
If the candidate is a very slow rider, to the extent that the test is likely to result in failure, the examiner should not persist on a route with dual carriageways and roads with fast moving traffic, as that could be hazardous for both riders. The route should be altered to cause the least danger.
All progress, or lack of it, must be commensurate with the size of machine and the road and traffic conditions. A rider should not necessarily be expected to ride at the speed limit, although riding well below it in good road and traffic situations would not be acceptable.
A candidate should not be encouraged to make better progress or to filter along a line of other vehicles. However, if a candidate chooses to filter and does so safely, it should not be regarded as a fault.
Positioning and rear observation
The candidate should take up the correct position on the road when riding straight ahead and when taking corners. Before changing direction, slowing or stopping they should take rear observation.
In difficult traffic situations where this might be hazardous, it is acceptable for them to use the mirror(s). The need to glance behind does not apply in the case of a candidate with a disability, which prevents them from taking direct rear observation; instead, observation should be made by use of suitably positioned mirrors.
Rear observation is a combination of looking behind and mirror checks, which ensures the rider is always fully aware of what is happening behind. The candidate should use judgement in deciding when to look behind.
Obviously when they are looking behind, they are not looking ahead. This could be hazardous if, for example, they are close to the vehicle in front or if they are overtaking at speed - it is often safer for them to keep their eyes on what is happening ahead.
Equally there are situations when it is potentially dangerous not to look behind, such as turning right from a major road into a minor road. In congested urban situations a candidate is expected to use the lifesaver as a last check into the blind spot before committing themselves to a manoeuvre.
Hill start
If the route includes an uphill section, the candidate should be asked to pull up at a suitable place on the gradient, and then asked to move off and continue on the same route. If a suitable hill start is not available, a designated stop must be conducted.
2.04 General guidance for motorcycles
Motorcycle clothing – general guidance
DVSA don’t want to prevent motorcycle riders taking their tests. However, both examiners and motorcycle trainers have a part to play in ensuring new riders understand the risks they face and do what they can to reduce these by wearing adequate protective gear. Examiners should use their experience and expertise to make an informed decision about the type of clothing the candidate is wearing, and whether it offers so little protection as to create a wholly unacceptable risk of injury if they fell from their machine.
Please bear in mind that some new riders can’t afford expensive clothing and may have tried their best to ensure they are adequately protected.
As a general guide the following is an indication of the type of clothing that riders should wear:
- motorcycle boots
- boots that provide support and ankle protection
- sturdy trainers/shoes
- textile or leather motorcycle trousers
- jeans/denim trousers
- heavy denim jacket
- textile or leather motorcycle jacket
- motorcycle gloves
The following is an indication of the type of clothing that isn’t acceptable:
- lightweight flimsy training shoes, sandals, canvas basketball trainers
- any clothing which leaves areas of exposed skin such as T-shirts or shorts
- shell suits or lightweight tracksuits
- distressed or ripped jeans
- lightweight fleece or hoody
- no gloves
Examiners should bear in mind the test should continue unless there’s clearly an unacceptable risk to the candidate. If the test has to be terminated the activity code to use is 21 - Vehicle/gear not suitable or no vehicle for test.
Candidates shouldn’t assume that their clothing offers appropriate protection simply because their test has gone ahead. It is always for the rider to ensure, for their own safety, that they wear suitable protective clothing and equipment.
Motorcycle Safety and Balance Questions
The candidate should be asked 2 machine safety check questions and one balance question relating to the carrying of a pillion passenger.
To ensure uniformity the safety questions must be selected from the bank of questions listed at Annex two. The balance question should be straightforward and not complex. A sample of questions is given below:
What problems could arise from carrying a pillion passenger?
How should a passenger be carried on the pillion seat?
How would the balance of the machine be affected if you carried a pillion passenger?
As a general rule the safety questions should be used in rotation. However, examiners will need to exercise common sense and discretion at times, for example if a particular machine does not lend itself to a question. The questions used (and the answers given) should be recorded on the digital test report if they affect the outcome of the test.
Although some checks may involve the candidate in identifying how fluid levels would be checked, pupils must not be asked to touch a hot engine or physically check the fluid levels.
Assessment
One or more questions answered incorrectly will result in one riding fault being recorded. However, examiners should not pursue questions unduly in an attempt to elicit the precise responses listed; they should bear in mind that these are basic safety checks, and that in-depth knowledge is not required for the answers to be acceptable.
If an Examiner has to take action to avoid danger to the candidate or another road user, an ETA will be recorded and a serious/dangerous fault recorded under the appropriate heading on the digital test report.
Radio equipment
After the usual pre-test preliminaries (e.g. licence and identification check) the examiner should help the candidate with the fitting of the radio and earpiece.
They should then accompany the candidate to the machine, explaining how the test will be conducted and how the radio equipment works. The examiner should make note of any non-standard controls on the candidate’s machine, but the machine or its controls should not be handled.
After the eyesight test, a sound check should be made to ensure that the candidate can hear the examiner’s instructions clearly. At the start of a motorcycle test examiners should explain to candidates that, should the radio fail during the test or they cannot hear the instructions for any other reason they should just pull up. They should not be instructed to ride along tapping the side of their helmet. Examiners should also explain that before the start of the independent section of the ride they will pull the candidate up and explain what is required.
Maximum use should be made of all available test routes to minimise annoyance to local residents.
Indicators
Motorcycles are not required by law to be fitted with direction indicators, but if they are fitted the law requires them to be in good and efficient working order at all times when the machine is in use on the road. Indicators on some small capacity machines tend to dim when the machine is travelling slowly or is stationary. This is due to machine design and tests should not be terminated on this account.
Motorcycle braking systems and ABS
It is important that examiners recognise the braking system of the machine presented for test, as this may influence the assessment in relation to front/rear brake use in normal riding and particularly for the emergency stop exercise.
Assessment
Examiners should accept for normal riding on machines with combined brakes fitted that the rear brake might be used more (or solely used) at slow speeds than with a conventional braking system.
When assessing the emergency stop the examiner must keep in mind that the most effective way to stop the machine quickly is still to use the front brake in conjunction with rear. However late or no use of the rear brake could be assessed as a rider fault if the machine stops quickly and under control. Very late or ineffective use of the front brake is not acceptable.
ABS - Anti-lock braking system
ABS is fitted to most motorcycles. Examiners should not enquire if a motorcycle presented for a test is fitted with ABS. Some ABS systems require the clutch to be pulled in and the front/rear brake to be applied at the same time to brake in an emergency situation; therefore, a fault should not be recorded purely for using this technique with a motorcycle fitted with ABS on the emergency stop exercise.
On the emergency stop exercise, under severe braking, tyre or other noise may be heard, this does not necessarily mean the wheels have locked and are skidding. Examiners should bear these points in mind when assessing the candidate’s control during this exercise.
Further advice regarding ABS is given in the DVSA publication “The Official DVSA Guide to Riding – the essential skills”.
Automatic transmission and E-Clutch systems
Candidates may take their test on a machine fitted with automatic transmission that meets the requirements. However, on passing their test, they will be restricted to riding automatic machines in the relevant sub-category.
Motorcycles fitted with an E-clutch system are only suitable for the manual test. These motorcycles cannot be used to obtain an automatic transmission licence. The candidate must ride the motorcycle in full manual mode throughout the entire test.
If the candidate appears to be using the bike during the test in automatic mode, the examiner will ask the rider to stop and check the gearbox setting.
If the candidate continues to use the automatic gearbox following a warning the examiner may stop and void the test.
Note: Riders with a registered physical disability may use the e-clutch as an adaptation.
Radio and examiner bike breakdown
If the radio equipment fails, every effort should be made to complete the test, and subsequent tests, by giving instructions on route as in the case of non-hearing candidates. Exceptionally it may be necessary to cancel alternate tests because of the time element. If the DTC does not carry spare radios, then examiners should contact their LDTM as soon as possible to arrange for spare Bluetooth equipment to be made available. Note: Examiners are permitted to carry out a Direct Access test without being in radio contact with the candidate.
If the examiner’s motorcycle breaks down, the test, and subsequent tests, should be cancelled unless the fault can be rectified quickly, or an alternative properly insured vehicle is available for use.
Reporting motorcycle related incidents
Off road includes incidents occurring during Module 1 testing, approved training bodies (ATB) activities on a motorcycle manoeuvring area (MMA) and compulsory basic training (CBT) and direct access scheme (DAS) activity at an ATB site. On road includes incidents occurring during Module 2 testing, any motorcycle incident involving a member of staff on DVSA business, CBT training during element E and DAS training.
The procedure can be found on the DVSA SharePoint site.
Safety, security, and care of DVSA motorcycles
Examiners must wear a class 3 fluorescent jacket (with sleeves) during the test.
Motorcycle examiners responsible for an official motorcycle should ensure at all times that when the machine is left unattended, the steering is locked, and the key kept in a safe place. If the machine is left unattended for longer periods, then additionally the locking ‘U’ bolt or padlock and chain must be used. Whenever possible, the machine should be kept undercover overnight.
If the motorcycle is taken home, the examiner should:
- store it in a safe location, preferably in a locked garage.
- if that is not possible, the bike must be kept off the road and secured by a suitable motorcycle lock and chain. A cover would also be beneficial to protect the bike from the elements and deter potential theft
- before periods of annual leave, a discussion should take place between the examiner and the LDTM to establish the most suitable place to store the motorcycle during the leave period. This could be at the test centre
Examiners with responsibility for cleaning an official motorcycle are allocated one period per month in which to do so. They should arrange with the LDTM and Deployment to have this period made available at a convenient time.
Category B1 & motor tricycles
Category B1 vehicles and motor tricycles are normally not suitable for test except in the case of a motor tricycle if the candidate has a notifiable disability.
Mopeds
The left / right bend (circuit ride), emergency stop exercise and the avoidance exercise should be carried out at a minimum speed of 30kph (18.75mph). Candidates who reach 27km/h or less will be asked to repeat the exercise providing they have not committed a serious or dangerous fault and providing their riding does not indicate it would be unsafe to continue. A rider fault will be assessed as the candidate has not achieved the minimum speed.
Candidates who fail to reach the minimum speed requirement but who achieve 28 or 29 km/h will not be asked to repeat the exercise; a rider fault will be assessed in addition to any other control or observation faults and should be recorded under ‘Emergency Stop’ or ‘Avoidance’. No more than one fault can be recorded for these exercises. The examiner should record the speed of each attempt at the avoidance exercise on the digital test report.
The first blue cone (adjacent to the red cone) that candidates are required to steer around during the avoidance exercise should be stepped in one metre. This narrows the space between the blue marker cones which represent the avoidance channel.
All other aspects of the test remain the same as for Category A tests.
Modified/unusual machines
If a candidate attends for test on an unusual motorcycle (i.e. a grey import) or they claim the motorcycle has been modified, the DVSA list of motorcycles suitable for test should be referred to. If the motorcycle is not listed examiners may be able to decide either from their own knowledge or any documentary evidence produced which category the motorcycle falls into.
In cases where the category cannot be decided then advice should be sought from the Technical Support Team. In all cases the category of the motorcycle must be decided prior to the start of the ride and the candidate should be informed of the decision.
Any modifications should be entered on the digital test report.
The DVSA list of motorcycles suitable for test can be found in the DT1 SharePoint site and it is also published on gov.uk.
Electrically assisted pedal cycles
Certain machines with the characteristics of conventional pedal cycles, but with a small measure of assistance from an electric motor, are excluded from the motor vehicle category in the Road Traffic Act. Riders of these cycles are therefore not subject to the driver licensing and testing regulations and, if candidates present themselves for test with one, they should be advised accordingly.
The machines are:
- bicycles with a kerbside weight not exceeding 40kg and an electric motor with a continuous rated output not exceeding 0.2 kilowatts
- tandem bicycles and tricycles with a kerbside weight not exceeding 60kg and an electric motor with a continuous rated output not exceeding 0.25 kilowatts
The machines are required to be fitted with pedals by means of which they can be propelled, an electric motor which cannot propel the vehicle when it is travelling at more than 15 mph, and a plate showing the manufacturer’s name and the continuous rated output of the electric motor.
Extended test
Candidates who are required to take an extended test will have to pass an ordinary length Module 1 and an extended Module 2 test. Both journals will show extended test.
The on-road riding time for an extended test must be at least 60 minutes; examiners should aim to spend at least 70 minutes on road to ensure this is met.
3. Vocational driving tests
3.01 Introduction
This chapter contains detailed guidance on the conduct of Medium and Large Goods Vehicle & Passenger Carrying Vehicle driving tests. Guidance, which applies to either LGV or PCV tests only, is annotated accordingly.
3.02 Driving test requirements
Driving tests are conducted in accordance with the provisions of the Motor Vehicles (Driving Licences) Regulations and EU Directive 2003/59/EC (as retained). Test candidates must satisfy the examiner as to their ability to carry out properly the activities and perform competently, without danger to and with due consideration for other road users, the manoeuvres below.
Category C1/C driving test requirements:
- vehicle safety checks: 5 vehicle check questions, including 3 “show me” questions and 2 “tell me” questions
- at least 60 minutes on the road and approximately 10 minutes of independent driving
- set exercises:
- uphill start
- downhill start
- controlled stop (angle start)
- stops:
- 2 normal stops
Category C1+E/C+E driving test requirements
For candidates Following the staging licence process:
- vehicle safety checks: 2 vehicle check questions, including 1 “show me” question and 1 “tell me” question
- at least 60 minutes on the road and approximately 10 minutes of independent driving
- set exercises:
- uphill start
- downhill start
- controlled stop (angle start)
- stops:
- 2 normal stops
For candidates without following the staging licence process (C or C1 Initially):
- vehicle Safety Checks: 5 vehicle check questions, including 3 “show me” questions and 2 “tell me” questions
- at least 60 minutes on the road and approximately 10 minutes of independent driving
- set exercises:
- uphill start
- downhill start
- controlled stop (angle start)
- stops:
- 2 normal stops
Category D1/D driving test requirements
- safety questions: 3 safety questions covering fuel cut off, fire extinguisher, and emergency door
- vehicle safety checks: 5 vehicle check questions, including 3 “show me” questions and 2 “tell me” questions
- at least 60 minutes on the road and approximately 10 minutes of independent driving
- set Exercises:
- uphill start
- downhill start
- controlled stop (angle start)
- stops:
- 2 bus stops
- 2 normal stops
Category D1+E/D+E driving test requirements
For candidates following the staging licence process
- safety questions: 3 safety questions covering fuel cut off, fire extinguisher, and emergency door
- vehicle safety checks: 2 vehicle check questions, including 1 “show me” question and 1 “tell me” question
- at least 60 minutes on the road and approximately 10 minutes of independent driving
- set exercises:
- uphill start
- downhill start
- controlled stop (angle start)
- stops: -2 bus stops
- 2 normal stops
For candidates without following the staging licence process (D or D1 Initially)
- safety Questions: 3 safety questions covering fuel cut off, fire extinguisher, and emergency door
- vehicle Safety Checks: 5 vehicle check questions, including 3 “show me” questions and 2 “tell me” questions
- at least 60 minutes on the road and approximately 10 minutes of independent driving
- set exercises:
- uphill start
- downhill start
- controlled stop (angle start)
- stops:
- 2 bus stops
- 2 normal stops
3.03 Test candidates
Test candidates must demonstrate competence in their ability to complete, without danger to and with due consideration for other road users, the following:
- answer vehicle safety check questions
Preparation to drive:
- adjust the seat as necessary to obtain a correct seated position
- adjust rear-view mirrors and seat belts
- check that the doors are closed
Technical control of the vehicle:
- start the engine and move off smoothly (uphill and downhill as well as on the flat)
- accelerate to a suitable speed while maintaining a straight course, including during gear-changes
- adjust speed to negotiate left or right turns at junctions, possibly in restricted spaces, while maintaining control of the vehicle
- brake accurately to a stop where directed, if need be by performing an emergency stop
- reverse in an ‘S’ shaped curve
Behaviour in traffic:
- observe (including the use of the rear-view mirrors) road alignment, markings, signs and potential or actual risks
- communicate with other road users using the authorised means
- react appropriately in actual risk situations
- comply with road traffic regulations and the instruction of the police and traffic controllers
- move off from the kerb or a parking space
- drive with the vehicle correctly positioned on the road, adjusting speed to traffic conditions and the line of the road
- keep the right distance between vehicles
- change lanes
- pass parked or stationary vehicles and obstacles
- approach and cross junctions
- turn right and left at junctions or to leave the carriageway
Where the opportunity arises:
- pass oncoming vehicles, including in confined spaces
- overtake in various situations
- approach and cross level-crossings
Trailers:
- un-couple and re-couple trailer or semi-trailer from and to the tractor vehicle
- vehicle Safety
- show awareness of vehicle safety measures and be able to operate safety systems.
3.04 Minimum test time requirements
It is important that, unless the test is terminated, the minimum driving times are strictly adhered to. Regulations state that the time during which a person is required to drive on the road is not less than 60 minutes in the case of a test for a licence authorising the driving of a class C1, C1+E, C, C+E, D1, D1+E, D, D+E.
3.05 Minimum test vehicles (MTVs) suitable for test purposes
All vehicles used for test must require the category of entitlement being applied for. If a vehicle presented for test can be driven using a lower category entitlement, it is not suitable for test, even if it meets the MTV requirements below.
For example, an electric powered, zero emission vehicle with a MAM of 4,250kg may meet the category C1 MTV requirements but can be driven using category B entitlement.
Category C1
- MAM* 4 tonnes
- Cargo compartment: Closed box construction at least as wide and as high as the cab
- RTM** Not applicable
- ABS: Yes
- Tacho: Yes
- Length: 5 metres
- Width (metres): Not applicable
- Speed km/h: 80
Category C1+E
- MAM* 4 tonnes + 2 tonne trailer
- Cargo compartment/trailer: Closed box construction category C1 vehicle with a closed box trailer at least as wide and as high as the cab. The trailer can be slightly less wide than the towing vehicle but rear view must be through external mirrors only
- RTM** 800kg for the trailer
- Load Requirement: 600kg of aggregates such as sand, stone chippings, gravel or any other recycled material packaged in sealed transparent bags. All bags must weigh the same and be at least 10kg. You can also use a single bag if it weighs 600kg or 1,000kg. Or alternatively: one intermediate bulk container constructed of moulded plastic or steel of 1,000kg or 600kg capacity when filled with water
- ABS: Yes
- Tacho: Yes
- Length: 8 metres
- Width (metres): Not applicable
- Speed km/h: 80
Category C
- MAM* 12 tonnes
- Cargo compartment: Closed box construction at least as wide and as high as the cab
- RTM** 10 tonnes
- Load Requirement: Five 1000 litre IBCs
- ABS: Yes
- Tacho: Yes
- Length: 8 metres
- Width (metres): 2.4 metres
- Speed km/h: 80
Category C+E drawbar (cat. C towing vehicle)
- MAM* 20 tonnes
- Cargo compartment: Closed box construction at least as wide and as high as the cab
- RTM** 15 tonnes
- Load Requirement: Towing vehicle - five 1000 litre IBCs. Trailer - three 1000 litre IBCs
- ABS: Yes
- Tacho: Yes
- Length: 14 metres. Trailer at least 7.5 metres
- Width (metres): 2.4 metres
- Speed km/h: 80
Category C+E articulated
- MAM* 20 tonnes
- Cargo compartment: Closed box construction at least as wide and as high as the cab
- RTM** 15 tonnes
- Load Requirement: Eight 1000 litre IBCs
- ABS: Yes
- Tacho: Yes
- Length: 14 metres
- Width (metres): 2.4 metres
- Speed km/h: 80
Category D1
- MAM* 4 tonnes
- 9 - 16 passenger seats
- Cargo compartment: Not applicable
- RTM** Not applicable
- ABS: Yes
- Tacho: Yes
- Length: 5 metres
- Width (metres): Not applicable
- Speed km/h: 80
Category D1+E (cat. D1 towing vehicle)
- MAM* 4 tonnes + 1.25 tonne trailer
- Cargo compartment: Closed box trailer at least 2m high and 2m wide
- RTM** 800kg for the trailer
- Load Requirement: 600kg of aggregates such as sand, stone chippings, gravel or any other recycled material packaged in sealed transparent bags. All bags must weigh the same and be at least 10kg. You can also use a single bag if it weighs 600kg or 1,000kg. Or alternatively: one intermediate bulk container constructed of moulded plastic or steel of 1,000kg or 600kg capacity when filled with water
- ABS: Yes
- Tacho: Yes
- Length: Not applicable
- Width (metres): Not applicable
- Speed km/h: 80
Category D
- MAM* Not applicable
- Cargo compartment: Not applicable
- RTM** Not applicable
- ABS: Yes
- Tacho: Yes
- Length: 10 metres
- Width (metres): 2.4 metres
- Speed km/h: 80
Category D+E (cat. D towing vehicle)
- MAM* 1.25 tonnes for the trailer
- Cargo compartment: Closed box trailer at least 2m wide and 2m high
- RTM** 800kg for the trailer
- Load Requirement: 600kg of aggregates such as sand, stone chippings, gravel or any other recycled material packaged in sealed transparent bags. All bags must weigh the same and be at least 10kg. You can also use a single bag if it weighs 600kg or 1,000kg. Or alternatively: one intermediate bulk container constructed of moulded plastic or steel of 1,000kg or 600kg capacity when filled with water
- ABS: Yes
- Tacho: Yes
- Length: Not applicable
- Width (metres): 2.4 metres
- Speed km/h: 80
There is no requirement for 8-forward gear ratios for categories C and C+E.
Key:
- MAM*: Maximum Authorised Mass = the maximum permissible weight of the vehicle or trailer or vehicle/trailer combination
- RTM**: Real Total Mass = the actual weight of the vehicle or trailer or vehicle/trailer combination when presented for test
Test vehicles used for large vehicle and vehicle-trailer combination tests (bus/lorry) must be fitted with external nearside and offside mirrors for use by the driving examiner during the test. Mirror Cam, which is a mirror replacement system, typically replaces the requirement to have an additional mirror for the driving examiner. Seatbelts for the examiner and any supervising officer must be fitted to lorries used for test, including with-trailer
Fire service exemption to minimum test vehicle requirement:
Exceptionally, for category C practical tests, regulations allow fire brigades to use either:
- the standard vehicle MTV as described above
- a fire tender completely filled with water - as indicated by the water gauge
If, while under the control of the fire service, a fire tender is presented for test filled with water, it must be accepted. Fire tenders are not acceptable for test if used by anybody other than the fire service (normal MTVs apply). If you’re in any doubt about the validity of a fire service test, contact delegated.testing@dvsa.gov.uk
3.06 Laden vehicles/trailers
Vehicles and trailers must be laden in accordance with the minimum test vehicle requirements detailed above. Exceptionally, it may be necessary for an examiner to check a load to ensure it meets the test requirement. If this is necessary, the examiner should ask the candidate or the accompanying driver to enable the load to be seen. The examiner must not physically open, or assist in opening, any vehicle or trailer, or operate any tail lift in order to gain access to a load. Under no circumstances should an examiner enter a vehicle or trailer loading area to check a load. Any viewing must be made from a point completely separate (detached) from the vehicle or trailer. If an examiner is trained to use an A-frame set of steps, they can be used but mustn’t be propped against or touching the vehicle. If it’s clear that a vehicle/trailer doesn’t comply with the load requirement, the examiner must explain to the candidate that they’re unable to conduct the test. Small, properly secured articles such as tarpaulins, cones - and equipment such as cookers and fridges, fitted in recreational vehicles, for example motorhomes , and other integral factory-fitted equipment - should not be regarded as a load.
3.07 Maximum length of LGV drawbar outfit
The maximum permitted length of a drawbar outfit on the road is 18.75 metres. When setting out the area to accommodate a vehicle of this length, the distance between cones A-A1 and cone B MUST be twice the length of the outfit. The bay should be set out as normal.
The area is 66 metres in length and this length can accommodate vehicles up to 16.5 metres. For vehicles over 16.5 and up to 18.75 metres, cones A-A1 should be set on the yellow line and cone B should be positioned 2 vehicle lengths away. This will mean that for these large vehicles the overall length of the area will be less than 4 times the length of the outfit.
3.08 Upgraded licences for category D1 and C1+E
Candidates attending for category D1 and C1+E tests who previously held D1 (restriction 101) or C1+E through acquired rights must take the appropriate theory test before they are entitled to take the practical test. In such instances ‘Check’ should appear on the journal, if confirmation cannot be obtained from either CSU or the theory test hotline before the test slot, the candidate should be asked to produce a valid theory test certificate or the test must be terminated.
3.09 General competence to drive
To pass the test, a candidate must demonstrate a high standard of competence in handling the vehicle. The candidate must also be able to apply the rules of the Highway Code. They must show that, generally, they have a full understanding of the principles involved in driving large goods or passenger-carrying vehicles and of the application of those principles and can demonstrate proper control in a wide variety of situations.
In addition, because of the size and weight of their vehicle, the drivers of lorries and buses must have a highly developed level of courtesy and consideration for other road users. The test will also include a section of independent driving where the candidate is asked to follow traffic signs or verbal directions or a combination of both.
3.10 Completion of the Digital Test Report
When using the Digital Test Report, it is specific to the candidate and test category. The digital journal contains further information relating to the candidate. This information can be accessed by selecting the candidate’s name on the journal. This must be done if there is a yellow exclamation marker next to the candidate’s name, ensuring the examiner is aware of any relevant information prior to the test.
3.11 Definition of markings on Digital Test Report - LGV
Module 3a tests:
- control: incorrect use of controls and/or inaccuracy and inability to complete the exercise in a reasonable time
- observation: lack of effective all-round observation
- coupling exercise: Incorrect/unsafe uncoupling/coupling procedure
Module 3b tests:
-vehicle checks: incorrect answer to vehicle check questions
- show me / tell me: incorrect answer to safety check questions
- Highway Code / safety: for categories F/G/H only. (PCV only) - incorrect answers to three safety questions
- PCV door exercise: any faults regarding safe practice at bus stops should be marked here
Control:
- accelerator: uncontrolled or harsh use of the accelerator
- clutch: uncontrolled use of clutch
- gears: failure to engage appropriate gear for road and traffic conditions. Coasting in neutral or with clutch pedal depressed
- footbrake: late and/or harsh use of footbrake
- parking brake: failure to apply or release the handbrake correctly and when necessary.
- steering: erratic steering, overshooting the correct turning point when turning right or left, both hands off steering wheel or hitting the kerb
Precautions:
- failure to take proper precautions before starting engine
Ancillary controls:
- failure to use ancillary controls when necessary
Move off:
- safely: failure to take effective observation before moving off, including the correct use of signals
- control: inability to move off smoothly, straight ahead, at an angle, or on a gradient
Use of mirrors:
- failure to make effective use of the mirrors well before:
- signalling
- changing direction
- changing speed
Signals:
- necessary: Necessary signal omitted
- correctly: Incorrect or misleading signal. Failure to cancel direction indicators
- timed: Signal incorrectly timed so as to be either misleading or too late to be of value
Junctions:
- approach speed: approaching junctions at a proper speed; either too fast or too slow, for whatever reason
- observations: Not taking effective observation before emerging
- turning right: Late or incorrect positioning before turning right, including failing to move forward into the correct position to turn right at traffic lights
- turning left: Positioning too close or too far from the kerb before turning left
- cutting corners: Cutting right hand corners, particularly where the view is limited
Judgement:
- overtaking: attempting to overtake unsafely or cutting in after overtaking
- meeting: failure to show proper judgement when meeting approaching traffic
- crossing: turning right across the path of oncoming traffic
Positioning:
- normal driving: incorrect positioning during normal driving, including cutting across the normal road position when going ahead at roundabouts without lane markings
- lane discipline: failure to maintain proper lane discipline at roundabouts with lane markings when going ahead and when continuing to drive ahead in designated lanes
Pedestrian crossings:
- failure to give precedence to pedestrians on a pedestrian crossing
- non-compliance with lights at pedestrian controlled crossings
Position / normal stops:
- normal stop not made in safe position
Awareness / planning:
- failure to judge what other road users are going to do and react accordingly
Clearance:
- not allowing adequate clearance when passing parked vehicles and other obstructions
Following distance:
- keep a proper and safe distance from the vehicle in front when moving
- leave a reasonable gap from the vehicle in front when stopping in lines of traffic
Use of speed:
- driving too fast for road, traffic and weather conditions
Progress:
- appropriate speed: driving too slowly for road and traffic conditions
- undue hesitation: being over cautious by stopping or waiting when it is safe and normal to proceed
Response to signs / signals:
- failure to comply with or late reaction to:
- traffic signs: Inappropriate response to traffic signs
- road markings: for example. double white lines, box junctions, lane direction arrows
- traffic lights: including failure to move off on green when correct and safe to do so
- traffic controllers: signals given by a police officer, traffic warden, school crossing warden or other persons directing traffic
- other road users: failure to take appropriate action on signals given by other road users
Examiner Took Action (ETA):
- examiner took action: verbally or physically (for example, dual controls/steering)
ECO:
- eco safe driving: not part of pass/fail criteria.
- control: starting/moving off/accelerator use/gears
- planning: hazard awareness/planning and anticipation/engine braking
3.12 Preparations for the test
3a: The examiner or assessor should take the following on test:
- digital device – iPad; Delegated examiners/Assessors DL25/PTR
- paper contingency test report - PTR
- pass certificate book - DVSA13
- manoeuvring board for reverse exercise
- statement of failure (external assessors)
3b: The examiner or assessor should take the following on test:
- digital device – iPad
- paper contingency test report – PTR
- DL25
- pass certificate book - DVSA10
3.13 Setting the manoeuvring area
The manoeuvring area should be laid out in exactly the same way for right and left-hand drive vehicles, and strictly in accordance with the examiner’s manoeuvring board and ready reckoner. If the examiner is doubtful about the accuracy of the dimensions of the vehicle as shown on the journal, they should be checked with a tape to ensure correct positioning of the marker cones.
The distance from cone B to cones A & A1 is always twice the length of the vehicle used for test. In the case of vehicles with trailers, cone A1 should be set one metre in from the boundary line. In the case of rigid vehicles without trailers, cone A1 should be set on the boundary line. Exceptionally, at centres where there is a safety barrier or other obstruction close to the boundary line and the rigid vehicle used for test has a large front overhang or limited steering lock, which may make it difficult to negotiate cone B, then cone A1 should be set one metre in from the line.
The distance between cones A & A1 should always be 1½ times the widest part of the vehicle (or outfit) used for the test and cone B should always be in line with cone A. Therefore, when cone A1 is set one metre in from the boundary line cones A and B must also be set an additional metre into the manoeuvring area.
3.14 Meeting the candidate
The examiner should ask for the candidate by name, greet them pleasantly and then carry out the same licence check and identification procedures as laid out in Chapter 1.
If the candidate arrives for their test in an automatic C1, C1E, C, CE, D1, D1E, D or DE category of vehicle, annotate the ‘automatic’ box when completing the Digital Test Report, the next question on the iPad, asks if the candidate has a code 78 (automatic restriction) on their driving licence. This then decides which licence will be issued. The same rule applies when completing a paper test report.
Where a test is being conducted by a delegated examiner, using a DL25 the ‘automatic’ box is only marked when the candidate has a code 78 restriction on their driving licence. If there is no code 78 (automatic restriction) on their driving licence, the ‘automatic’ box should not be marked.
If a candidate attends to take a C1 test and only has category C provisional entitlement on their driving licence or a D1 test and only has category D provisional entitlement on their driving licence, the test can continue as normal. The provisional entitlement for the subcategories C1/D1 is included with the C/D provisional entitlement. On PCV tests where routes incorporate bus lanes, candidates should be advised to use them as they would normally (PCVs can use bus lanes whether they are in service or not). The only bus lanes that shouldn’t be used are those marked ‘LOCAL BUSES’.
3.15 Eyesight test
The candidate’s eyesight is tested as part of the medical examination necessary before they can obtain a provisional licence as such there is no requirement to conduct an eyesight check.
3.16 Vocational driving licence restriction code 01 – eyesight correction
When a candidate takes a practical test for a lorry or bus, there is no requirement to carry out an eyesight test. If the candidate has restriction code 01 in column 12 on the rear of their driving licence, it means they may need to wear glasses or contact lenses. If they are not wearing glasses or contact lenses, the examiner should make suitable enquiries. If they confirm they have never worn glasses or contact lenses, or they have had corrective eye surgery, the examiner should advise the candidate to inform the DVLA.
If the candidate needs to wear glasses or contact lenses, the test should only be conducted if these are worn. Where the test does not go ahead in these circumstances, code 82 - not conducted incorrect/no lenses worn (VOC) should be used.
3.17 Vehicle safety questions
On vocational tests, safety questions must be asked as part of the preliminaries of the test prior to any on-road driving.
Examiners must choose a selection of either five questions for a rigid vehicle or two for a vehicle and trailer test in categories C and D. For lorry and trailer, PCV and trailer (C+E & C1+E, D+E & D1+E) categories, candidates will normally have answered five questions at the C & D testing stage. If category C or D is present on the driving licence, then only two further questions—one ‘show me’ and one ‘tell me’—will be asked. If, on checking the licence, the categories C & D are not present, then five questions will be asked. The questions specific to the above tests should be used (Annex 8), as far as possible, in rotation, and the questions selected should be recorded on the Digital Test Report/DL25.
Note: The candidate may not have gone through licence staging; a check should be made on the reverse of the licence for categories held. A prompt on the iPad will ensure that this is established. Questions should be chosen from the question bank and should suit the vehicle presented for the test. At least 50% of the questions should be ‘show me’ rather than ‘tell me’, therefore when asking two questions at least one must be ‘show me’. When asking five questions at least three must be ‘show me’. Examiners should use all of the questions equally. The choice of questions used should be recorded on the Digital Test Report/DL25 and will be subject to quality assurance.
Although some checks may involve the candidate in opening the engine cover or compartment to identify where fluid levels would be checked, candidates must not be asked to touch a hot engine or physically check the fluid levels.
Safety questions - assessment
A driving fault will be recorded for each incorrect answer up to a maximum of four driving faults. If the candidate answers all five questions incorrectly, a serious fault will be recorded. However, examiners should not pursue questions unduly in an attempt to elicit the precise responses listed; they should bear in mind that these are basic safety checks and that in-depth mechanical knowledge is not required for the answers to be acceptable. If an Examiner has to take action to avoid danger to the candidate, examiner, or another road user, an ETA will be recorded and a serious/dangerous fault recorded under the appropriate heading on the Digital Test Report.
As vehicle technology advances, more and more vehicles are being equipped with electronic diagnostic systems that inform the driver of the state of the engine fluid levels, tyre pressures, etc. It will be acceptable for a candidate to refer to the vehicle information system (if fitted) when answering questions on topics such as these. Examiners need to be aware that although it may be necessary in order to carry out some of the checks, the ability to open the engine cover or compartment is, in itself, not one of the competencies which candidates are required to demonstrate. Should a candidate experience difficulty, it will be acceptable for the accompanying driver to assist in the opening and closing of the engine cover or compartment Candidates should not be penalised if this proves necessary.
Drivers seeking vocational licence entitlement should be experienced and technically expert. The assessment criteria reflect this. Examiners should also be aware that many haulage, bus and coach companies have a policy of not allowing drivers to remove inspection covers or become involved in the routine mechanical maintenance of their vehicles. It may also be that specialist equipment is needed to carry out some procedures. This means that some ‘show me’ questions will have, to some extent, to be treated as ‘tell me’. Examiners will have to use their knowledge, judgement and common sense to assess the acceptability of the answers given. Simply pointing out that ‘The fitter always does that’, for example, would not be an adequate response, whereas an answer that demonstrates an understanding of the topic would be acceptable.
The assessment criteria reflect the knowledge and understanding expected of a competent vocational driver. One incorrect answer will result in a driving fault being recorded. Both questions answered incorrectly will result in a serious fault being recorded. In the case of five questions, a driver fault will be recorded for each incorrect answer up to a maximum of four driving faults. If the candidate answers all five questions incorrectly, a serious fault will be recorded.
3.18 Direction indicators and brake lights
The examiner should make a brief visual check of direction indicators and brake lights. If this reveals any obvious damage, the candidate should be given the opportunity to rectify the fault. If the fault cannot be rectified, the test should be terminated. To avoid subsequent argument, the candidate should be asked if they wish to confirm by personal observation that the particular item doesn’t function satisfactorily, in which case the examiner should operate the control. In deciding whether or not direction indicators and stop lamps are in an acceptable condition for the purposes of the test, examiners should be guided by the principle that no candidate should be turned away whose test could reasonably be conducted.
3.19 ‘L’ (‘D’ in Wales) plates
Regulations require the vehicle to display ‘L’ or ‘D’ plates, that are clearly visible from the front and rear of the vehicle.
3.20 Observation of candidate
Except for the reversing exercise, examiners should, throughout the test, position themselves within the vehicle where they are best able to observe the candidate’s performance. PCVs used for driving tests must have suitable examiner seats (with seat belts) and mirrors. Even then it may occasionally be necessary for examiners to stand or move around. They should preferably only move when PCVs are stationary or travelling in a straight line, without excessive acceleration or braking, and should also note the location of suitable grab rails and use them when standing, moving around, or sitting down. These safety precautions will continue to be required and must be observed by all examiners involved in PCV testing.
3.21 LGV safety & safety equipment knowledge for PCV candidates
It is the candidate’s responsibility to see that all doors, drop-sides, and tailboard and any equipment carried are properly secured. In the case of an articulated vehicle or drawbar outfit, they should also check that the trailer brake lines and lighting leads are properly connected and that the semi-trailer parking brake is not set. These checks would normally have been made prior to attending the test.
3.22 PCV safety questions
These questions must be asked in addition to the Vehicle Safety Check Questions. PCV candidates need to demonstrate their knowledge of the safety equipment fitted to their vehicle. The candidate should be asked to show the examiner where the fire extinguisher is, where the fuel cut-off device is, where the emergency door is, and how it operates. If the emergency door will not operate, then the test should be terminated. Note: there is no legal requirement for a training vehicle to carry a fire extinguisher. Therefore, if one is not present the test should proceed. Some vehicles don’t have a rear emergency door, it is replaced with break glass. An explanation of this would be sufficient and the vehicle is suitable for test.
3.23 Starting the engine
The candidate should ensure that the handbrake is applied, and the gear lever/selector is in neutral before operating the starter. Before moving off initially, the candidate should check the seat position and mirrors and, in the case of vehicles fitted with air pressure brakes, the instrument panel to ensure correct working pressure.
3.24 Reversing exercise
The exercise is designed to test the candidate’s accuracy in manoeuvring the vehicle when reversing. The degree of accuracy required is the ability to occupy a bay 1½ times the width of the vehicle and with the rear of the vehicle within the stopping area. The candidate should maintain all-round observation during the exercise. The examiner should observe the candidate’s performance from outside the vehicle, moving from one vantage point to another while the exercise is being performed. Before the exercise, the candidate should be asked to bring the vehicle to rest in the starting position. The examiner should then clearly explain the exercise to the candidate, making full use of the manoeuvring board to describe the requirements and giving precise directions as to the course to be followed. It should be explained to the candidate that they should not touch any of the marker cones or cross the yellow boundary lines during the exercise. To pass, the candidate should not cross any of the yellow boundary lines with the full width of a tyre whilst manoeuvring, nor should they displace any of the marker cones. Cones A & A1 mark the maximum length of the area to be used by a particular test vehicle. If ‘shunting’ should prove necessary, the candidate should not drive further forward than the boundary of the area marked by cones A & A1, nor take more than two shunts throughout the exercise.
Drivers of LGVs should aim to stop with the extreme rear of their vehicle in the section of the yellow stopping area covered with black cross-hatching. Stopping with the vehicle touching the barrier should not be regarded as a fault but displacing it should be viewed as unacceptable. Stopping in the yellow box, but short of the hatched area, should be viewed as unacceptable. The loading/unloading barrier is not part of the reverse exercise for PCV tests. Examiners should not refer to the barrier during a de-brief or in the driving test report. If Examiners identify an operational need to reposition the barrier away from the stopping area during a PCV test, then they can do so. On PCV tests, candidates should aim to position the extreme rear of the vehicle within any part of the yellow stopping area, including the black cross-hatching. Stopping short of the area or reversing through the stopping area (displacing the barrier) should be viewed as unacceptable.
3.25 Candidate external vehicle checks
During the reverse exercise, the candidate may wish to exit their vehicle to check its position. They are allowed to do this before reaching cone B (to assess their position in relation to it) and when in the bay to assess the rear position in relation to the stopping area/barrier. These are the only two occasions when the candidate is allowed to leave the vehicle during the exercise. No further attempt to exit the vehicle to make a check is permitted. Note: There are no driver faults recorded during the off-road section. The test would be deemed either successful or unsuccessful.
3.26 On entering the vehicle
Ask the candidate if the load is secure (except categories C1, D1 & D) and in the case of a tilt cab, ask the candidate if they are satisfied that the cab locking mechanism is secure. Before starting the drive, the examiner must ensure that their seat belt is worn and securely fastened. DVSA examiners, their managers, and other DVSA staff must not occupy unsafe or unsuitable non-standard LGV 3rd seats under any circumstances. When 3rd seats are not present, examiners should not be accompanied by any 3rd parties; DVSA staff or otherwise. Under no circumstances should anyone sit on engine covers, etc.
3.27 Controlled stop / angle start
Although at no time during the test should the candidate be asked to drive in anything other than the normal gear ratio, they may elect to use a 2-speed axle or other form of ‘split’ gear change. Any fault committed should be assessed and marked in the usual way. If a candidate asks for guidance on what is required, they should be told that they will not be expected to demonstrate use of a 2-speed axle or auxiliary transmission unless circumstances arise during the normal course of driving which require its use.
3.28 Planning
The examiner should take particular note of the candidate’s judgement of distance, as well as seeing that they look well ahead. They should have regard to the candidate’s all-round observation and use of mirrors, and note if their actions are deliberate and indicate a thoughtful appraisal of the situation.
3.29 Hazard recognition
Examiners should satisfy themselves that the candidate recognises hazards in good time and takes appropriate action. The examiner should observe whether the candidate keeps their vehicle under proper control, in the appropriate gear, and is unhurried in their movements. Late and sudden braking or gear changing shows a lack of foresight.
3.30 Road junctions, including roundabouts
The examiner should observe whether the candidate takes account of the type of junction, road signs, and following traffic. The candidate should take effective observation, including use of mirrors, before entering the intersection, and do so with proper regard for other road users. Necessary and appropriate signals should be given in good time, speed adjusted as necessary, and the vehicle correctly positioned throughout. The candidate should avoid using the weight and size of the vehicle to take precedence.
3.31 Turning right and left
The examiner should observe whether the candidate takes account of the type of junction and any warning signs, as well as keeping the vehicle under proper control. They should use the mirrors effectively, give proper signals in good time, select the appropriate gear, and take up the correct road position well before turning. Effective observation should be taken before emerging, and the proper position on the road taken up as soon as possible after turning. According to the length of the vehicle, a degree of tolerance may be allowed when assessing the vehicle’s position before and after turning, particularly where roads are narrow or the angle of the corner is acute.
When turning left, a candidate driving a long vehicle should position it some distance from the nearside kerb before turning, to avoid the rear nearside wheel encroaching on the pavement. Sharp swing-out should, however, be avoided and, bearing in mind the danger of cyclists or other road users on the nearside, the candidate should exercise extreme care and make full use of the nearside mirror. When turning right in long-wheelbase vehicles, cutting the corner is unavoidable in some situations; in such circumstances, the candidate must be expected to exercise extreme caution.
3.32 Overtaking, meeting, and crossing
The examiner should observe the candidate’s actions in overtaking and meeting other vehicles, and crossing the path of other traffic when turning to the right. Before overtaking, the mirrors should be used to observe following traffic in good time, and appropriate signals given if necessary. The examiner should bear in mind that this should be done much earlier than in, say, a car. While showing consideration for other traffic, the candidate should not exhibit nervousness by giving way unduly to other vehicles when they could be expected to proceed. On the other hand, they should not be inconsiderate, e.g. by turning right in the face of closely approaching traffic or, when overtaking, using the weight and size of the vehicle to intimidate approaching drivers into giving way. The candidate must allow for the width and length of the vehicle, and a high degree of accuracy in road positioning is expected.
When overtaking, the candidate should be sure that the vehicle has sufficient reserves of power and speed to complete the manoeuvre within a reasonable distance, so that following drivers who may wish to overtake are not unduly inconvenienced. The use made of a nearside mirror is very important. The examiner should note carefully the candidate’s use of it to ensure that following road users are not inconvenienced or placed in danger as a result of the vehicle’s change of position, e.g. a return to the nearside from a position or lane away from the left of the carriageway.
3.33 Traffic lights
The candidate’s reaction to the lights should be noted. An increase of speed where the lights have been showing green for some time could indicate a tendency to rely unduly on the colour remaining at green or to proceed on amber when they should have stopped.
3.34 Traffic lanes
The candidate should try, wherever possible, to keep within the appropriate lane. However, with a large or long vehicle, there may be occasions when it is necessary to straddle or ‘shut down’ lanes to be able to negotiate a hazard safely.
3.35 One-way streets
The examiner should observe whether the candidate maintains a suitable course when driving along a one-way street and, when intending to turn right or left, takes up a correct position. If directional arrows appear on the road, the candidate should follow the course indicated for the intended direction.
3.36 Stopping normally
The candidate should be able to pull up parallel to, and within a reasonable distance of, the nearside kerb. The examiner should observe whether the candidate then applies the handbrake and puts the gear into neutral. On these occasions, failure to select neutral should not necessarily be regarded as a fault.
3.37 Normal stops on vocational tests
The following number of stops should usually be carried out for the different vocational tests:
C1, C1+E, C and C+E:
- uphill and downhill starts
- 2 normal stops
- angle start/controlled stop
D1, D1+E, D, D+E:
- Uphill and downhill starts
- 2 normal stops
- 2 bus stops
- Angle start/Controlled stop
3.38 Operation of doors on PCV test
The following procedure should be followed:
During the PCV driving test, examiners should ask the candidate to pull up on two separate occasions at an empty bus stop in a position where passengers can alight and embark safely.
During these stops, and only on vehicles fitted with doors that can be operated from the driver’s seat, the door should be opened and closed. In exceptional circumstances, and to prevent passengers embarking (at a normal bus stop), a suitable lamppost can be used instead of a bus stop. For assessment purposes, the handbrake should be applied whenever the door is open.
In the case of a PCV, the candidate should be able to stop the vehicle within stepping distance of the nearside kerb and, at bus stops, to bring the exit to the correct position in relation to the stopping place.
3.39 Consideration for other road users: anticipation of their probable actions
The examiner should take particular note of the candidate’s anticipation, observation, and consideration for other road users. Full use of the mirrors should be made to help faster traffic to overtake. Sufficient distance should be kept from the vehicle in front to allow overtaking drivers to pull in if necessary. Lane discipline should be maintained at all times. The early recognition of potential danger is extremely important. The examiner should look for prompt and appropriate reaction to signals given by other road users. They should also note the candidate’s reaction to the cyclist who has just looked round, children or other pedestrians moving towards the kerb, the opening of car doors, etc.
3.40 Use of ancillary controls
Candidates should be able to use all the ancillary controls fitted to their vehicle. If the candidate has problems using the controls, e.g. wipers, or if the candidate has to be reminded to use a control, the examiner must make a judgement on seriousness using the normal criteria.
3.41 Uncoupling and recoupling
A candidate taking their test in a vehicle drawing a trailer must give a practical demonstration of uncoupling and recoupling. The vehicle must be parked alongside the trailer after uncoupling; approximately parallel and level with it. After initially checking their trailer, it is not essential for them to leave the cab again to check the coupling height. However, if they choose to get out of the cab to check their position, they can do this as many times as they need to satisfy themselves the vehicle and trailer are realigned correctly. For smaller trailers, for example those towed by a minibus, after reversing the towing vehicle up to the trailer, it is acceptable if the candidate physically moves the trailer to line it up to recouple it. On the other hand, if they are not physically capable of moving the trailer (or they choose not to), it may take them several attempts to line the vehicle up to the trailer. There isn’t a set amount of attempts allowed to realign the vehicle to the trailer, but if excessive attempts are taken with little or no sign of improvement, it would not be considered acceptable. Strike plates, additional mirrors, and reversing cameras can be used to help realigning the vehicle to the trailer.
A physical check is usually necessary to ensure the trailer parking brake is applied before recoupling; however, if it is obvious it is applied from the position of the button or cable, a visual check is acceptable.
Please note: Throughout the exercise, before the candidate exits the cab, they must apply the parking-brake on the prime mover. If, however, the examiner has any doubts, they should ask the candidate to confirm it’s been applied before the candidate exits the cab. If the examiner is certain that without their intervention, the candidate would not have applied the parking-brake, a serious fault should be recorded.
The underrun bar on the prime mover of a draw-bar combination can be left up in the running position throughout the exercise.
Reasonable adjustment may be made for disabled drivers of other categories which would enable them to carry out the uncoupling exercise in a way that accommodates their disability. These reasonable adjustments will vary on a case-by-case basis and must be agreed in advance of the test with delegated.testing@dvsa.gov.uk.
3.42 LGV - uncoupling/re-coupling – stowing ‘suzis’
During the exercise with an artic, the ‘suzis’ should be stowed correctly and not allowed to trail. The object of the uncoupling exercise is to check that the driver parks the trailer safely as though they were leaving it there. The ‘suzis’ on a draw-bar trailer are left with the trailer and should be left in a safe position, for example laid over the draw-bar.
3.43 Fuel efficient driving (Eco-safe driving)
Fuel-efficient driving is a recognised and proven style of driving. It contributes to road safety while reducing fuel consumption and emissions and reflects the increased awareness and need for economical/environmentally friendly driving. Fuel-efficient driving does not contribute to the result of the test.
There are two fuel-efficient driving headings: control and planning.
Whether the result of the test is a pass or a fail, if a fuel efficient has been recorded in either one or both of the boxes, the examiner should debrief the candidate in the normal way.
3.44 End of test - issue of documents
At the end of the test, the examiner should advise the candidate of the test result.
Module 3a
Module 3a completion of the DVSA 13. Explain that the DVSA 13 needs to be presented to the examiner prior to the Module 3b test going ahead and should be kept safe.
The driving licence should not be taken on successful completion of the Module 3a test. Candidates will need their licence for the Module 3b.
If unsuccessful the candidate must be issued a statement of failure (external assessors only)
Module 3b
If a successful candidate has completed their test in an automatic category C1, C1E, C, CE, D1, D1E, D, or DE vehicle - and they already hold a full manual driving licence for any other category of car, lorry, or bus - after the text ‘automatic,’ answer ‘no’ when completing the DVSA10.
Other necessary documents should be completed and an oral explanation given in accordance with the guidance given in Chapter 1.
The candidate may have a Module 4 CPC test booked after this test (either straight away or in the very near future) and will require their licence for ID purposes. Ask if this is the case. If so, the candidate should not follow the ADLI route, and the licence should not be taken from them
3.45 General guidance for LGV
Breakdown of vehicle on manoeuvring area
If a vehicle breakdown obstructs the manoeuvring area to the extent that exercises cannot be carried out, and removal is beyond the resources immediately available, the nearest service station with a recovery vehicle should be contacted.
Examiners MUST not attempt to remove a disabled vehicle by pushing, nor invite anyone else to do so.
A list should be maintained of the names, addresses, and telephone numbers of garages in the vicinity of the centre, which operate heavy recovery vehicles.
Motorhomes / recreational vehicles
Motorhomes, recreational vehicles, etc. are either Category C or C1 dependent on the MAM. They should be taken on test provided that they meet the MTVs for the Category.
Stretched limousines and prison vans
Stretched limousines and prison vans based on a lorry chassis are not suitable vehicles for a PCV (category D/D1) test.
Trade plates
A vehicle carrying a trade plate is not a suitable vehicle for a driving test as the conditions attached to trade licences do not allow for a vehicle to be used for this purpose.
Traffic cones
A supply of about 30 cones (Glocone HN 18/3) should be maintained at permanent centres and about 20 cones at occasional centres. Requests for necessary replacements should be sent through to the LDTM.
4. Tractor and specialist vehicle driving tests (categories F, G, H and K)
4.01 Preparations for the test
The examiner should take DVSA10 forms, an iPad, Traffic signs-DT5, Highway Code Questions and paper contingencies for the test. In the case of tractor and specialist vehicle tests, the official tape must also be carried.
4.02 Preliminaries
As per the car test.
4.03 Test requirements
Examiners must conduct these driving tests on foot, they are not permitted to ride in or on the vehicle.
A suitable location for the test should be arranged with the candidate through the tractor and specialist vehicle tests team within Deployment and the relevant DTC.
The test must be conducted on-road at a location where the examiner can see the candidate making left and right turns. Exceptionally, the manoeuvre(s) (only) can be carried out off-road if there is the possibility of the vehicle damaging the road, but if the vehicle cannot be driven normally on-road, it is not suitable for test.
The Regulations require the candidate to demonstrate competence to drive the vehicle without danger to other road users and, where possible, be observed to drive on roads outside built-up areas and, if necessary, on urban roads.
Additionally, the Regulations require the candidate to act correctly and promptly on all signals given by traffic signs and traffic controllers, take appropriate action on signs given by other road users, and demonstrate appropriate signals in a clear and unmistakable manner. In the case of a vehicle with left-hand drive or a disabled candidate for whom it is impracticable or undesirable to give signals by arm, there is no requirement to give signals that cannot be given by mechanical means.
Regardless of the transmission configuration of the vehicle presented for test, driving licences for categories K, F, G & H are not restricted to vehicles with automatic transmission. Therefore, when completing the Digital Test Report for categories K, F, G & H, the automatic box should not be marked because it will cause a conflict with DVLA’s system and delay the licence being issued.
The usual driving test preliminaries of licence checks, identification, eyesight, etc., should be carried out.
Examiners must ensure they have an approved tape measure with them in case of an eyesight failure.
Two Safety Check Questions should then be asked.
The candidate is then directed where to go, with the examiner walking to various vantage points to observe the candidate.
The normal rules of assessment should be applied.
Examiners who are not familiar with conducting tests of this type should seek guidance from their LDTM.
The route number for a tractor and specialist vehicle tests is 88. The standard category ‘B’ test duration should be adhered to.
The candidate will not have taken a theory test, so at the end of the practical drive, the examiner should ask five questions on the Highway Code and other motoring matters and a sixth question comprising six traffic signs from the DT5. As these types of vehicles are not allowed to drive on motorways, questions should not be asked on this subject.
4.04 Unitary test requirements for categories F, G, H & K
All the requirements of the test must be carried out:
- read in good daylight (with the aid of corrective lenses if worn) a registration mark fixed to a motor vehicle and containing letters and figures 79 millimetres high and 50 millimetres wide, at a distance of:
- 12.3 metres for category K
- 20 metres for categories F, G & H
- answer vehicle safety check questions
- start the engine of the vehicle
- move away straight ahead and at an angle
- overtake, meet and cross the path of other vehicles and take an appropriate course
- turn right-hand and left-hand corners correctly
- stop the vehicle in an emergency and normally, and in the latter case, bring it to rest at an appropriate part of the road
- answer Highway Code questions
Additional requirements for categories F & G
Carry out a manoeuvre involving the use of reverse gear—usually a left-hand reverse (except in a case where the vehicle is not fitted with a means of reversing).
Additional requirements for category H
Drive the vehicle backwards and cause it to face in the opposite direction by means of its tracks.
4.05 Minimum test vehicle requirements
Minimum Test Vehicle (MTV) requirements and minimum age for categories F, G, H & K:
All vehicles presented for test must be legally roadworthy and covered by insurance for use on test by the candidate.
Not all vehicles in categories F, G, H & K are fitted with indicators & stop lamps; such vehicles are suitable for test, provided the candidate can give signals by arm.
Agricultural tractors - category F:
- have two or more axles
- are constructed for use as a tractor for work off the road in connection with agriculture or forestry
To drive tractors on public roads, you must be at least 16 years old.
At 16, you are restricted to a tractor that is no more than 2.45 metres wide and only driving on the road when travelling to and from a driving test appointment until you’ve passed your category F driving test.
At 17 years old, you can drive any tractor, and you can drive unaccompanied on the road displaying L plates, or D plates in Wales.
Road rollers - category G:
Before you can apply for a provisional licence for a category G, you must hold a full category B driving licence.
At 17 years old, you can drive a road roller:
- with metal rollers
- weighing less than 11.96 tonnes unladen
- which isn’t steam-propelled
At 21 years old, you can drive other road rollers:
- which have pneumatic, resilient, or elastic tyres
- that weigh more than 11.96 tonnes unladen
- that are steam-propelled.
Track-laying vehicles steered by means of their tracks - category H:
Before you can apply for a provisional licence for a category H, you must hold a full category B driving licence.
At 17, you can drive track-laying vehicles up to 3.5 tonnes MAM.
At 21, you can drive track-laying vehicles over 7.5 tonnes MAM.
If the candidate’s view is so restricted that they cannot make their own decisions about emerging at a junction, etc., and need the assistance of a third party (e.g., tank commander), then the vehicle is unsuitable for the purposes of a driving test.
Quad-tracks (or four-tracks) steer by means of articulating their body with hydraulic rams and do not steer by means of their tracks. Therefore, if they are constructed for use as a tractor for work off the road in connection with agriculture or forestry for driving licence and test purposes, they are category ‘F’.
A mowing machine or pedestrian-controlled vehicle - category K:
This is a specialist, ride-on, grass-cutting vehicle with permanent cutting equipment. You must be 16 years old to drive one of these vehicles.
A pedestrian-controlled vehicle is a powered vehicle where the operator walks with the vehicle and does not ride on it. This vehicle is not treated as a motor vehicle, and the operator does not need a driving licence.
5. Driver CPC part 4 practical safety demonstration test
5.01 Introduction
This chapter sets out the background and basic requirements of the Driver CPC module four practical safety demonstration test. It also gives detailed guidance on conducting the test.
5.02 Test requirements
The module four practical safety demonstration test is conducted in accordance with the provisions of EU Directive 2003/59/EC, The Vehicle Drivers (Certificates of Professional Competence) Regulations 2007, and The Motor Vehicles (Driving Licences) Regulations.
The practical safety demonstration test is a stand-alone practical test of 30 minutes duration focussing on vehicle safety and security, which covers categories C and D and all subcategories including trailers.
Questions posed will be answered using a static vehicle which needs to meet current minimum test vehicle (MTV) requirements. Despite being static, the candidate may elect to make a rolling brake check. If a candidate elects to do this they must not be stopped from doing so. The same question topic areas are covered for categories C and D although questions and test reports differ slightly.
Candidates will be asked to demonstrate their knowledge and ability in the following subject areas:
- ability to load the vehicle with due regard for safety rules and proper vehicle use
- security of the vehicle and contents
- ability to prevent criminality and trafficking in illegal immigrants
- ability to assess emergency situations
- ability to prevent physical risk
5.03 General competence
The object of the test is to ensure that the candidate has a sound knowledge of the test subject areas and can show this in a practical way. Examiners and assessors should remember that many candidates will be more nervous during the test than when practising with their instructor or with a friend. A pleasant outgoing approach, not only in the waiting room and on the way to the vehicle, but throughout the test is particularly important to help candidates to relax.
Emphasis must be on the candidate demonstrating their ability to answer the questions. For example, the candidate will be expected to make a physical check of certain equipment fitted to the vehicle, rather than tell you where it is and how to operate it.
For LGV practical demonstration tests only, a piece of equipment may be required. This is the Load Securing Demonstration Trolley (LSDT). This may be used by candidates to demonstrate their ability to secure and un-secure loads using the equipment provided which includes the use of rope, chain, a webbing strap and a load tensioning bar. Alternatively, additional suitable vehicle(s) can be used to demonstrate their ability to secure and un-secure loads.
There is no eyesight check requirement for this test and no need for L plates.
5.04 Minimum test vehicle (MTV) requirements
The test must be conducted using a vehicle which meets minimum test vehicle requirements (MTV). However, as the vehicle is being used in a static off-road environment, there is no need for the vehicle to be loaded or fitted with additional mirrors for the examiner to use. This exception to the MTV requirements applies to the Driver/CPC module four test only.
Examiners and assessors should note the Driver/CPC module four test is not a licence acquisition test. Therefore, a candidate may produce any vehicle for the Driver CPC/test so long as it meets the MTV for the vehicle presented (categories C, D and all subcategories as applicable) which may also be subject to the exception detailed above.
If, during the course of the test, the examiner or assessor notices a problem with the vehicle (for example, a defective bulb) as the test is being conducted off-road, the test must continue.
5.05 Explanation of form CPC4
Accurate completion of the digital test report or for external assessors the CPC4 is very important to allow for accurate data collection.
There are two sets of CPC question banks - one for PCV and one for LGV assessments. Each bank contains eight different combinations which should be used in rotation, an equal number of times. The digital test report is automatically linked to the digital journal which will ensure the correct category of CPC test report is completed. Make sure you have the correct CPC4 relevant to the category of test (LGV or PCV) this can be found at the top right-hand corner of the CPC4A
5.06 Assessment and control of the test
Examiners and assessors mark the positives, if the candidate demonstrates practical and theoretical knowledge.
If you look at any question combination, there are performance criteria. These are ‘Key Knowledge Indicators’ (KKI). If the candidate makes acceptable reference to the performance criteria listed, a mark is placed in the corresponding box on the digital test report. When all of the questions have been answered, the digital test report totals the number of KKI boxes marked to produce the individual question score. The score to each question will be in the form of a percentage: 5, 10, 15, and 20. To summarise:
- 1 KKI box marked equates to a 5 per cent question score
- 2 KKI boxes marked equates to a 10 per cent question score
- 3 KKI boxes marked equates to a 15 per cent question score
- 4 KKI boxes marked equates to a 20 per cent question score
The fifth question on all forms has ten KKI boxes. Each box equates to 2%. The digital test report will total the number of KKI boxes recorded, rounding up or down as necessary. For example: seven KKI boxes marked (7 x 2 = 14) therefore mark the 15 per cent score box. Six KKI boxes = 10 per cent, and so on.
Individual question scores are added together to produce a total score which will be recorded in the total section. The candidate must attain a minimum of 15% in all questions and a total score of at least 80% to pass. It is possible for a candidate to score 90% and not pass (20% in 4 questions and only 10% in the fifth).
Examiners or assessors should ensure their instructions are clear and understandable so that candidates know what is expected of them.
5.07 Prompting
Examiners or assessors are required to ask candidates five main questions which can contain sub-questions. In order to establish a candidate’s ability and knowledge it will often be necessary to prompt for an answer. Any prompt given must not contain clues or lead the candidate in any way.
Here are some examples of good and bad prompts:
Bad:
- examiner or assessor: ‘What about if you needed to warn somebody?’
- candidate: ‘Oh yes, I forgot, the horn. I could use the horn.’
- examiner or assessor: ‘Would you check the baggage lockers as well?’
- candidate: ‘Oh yes, of course.’
Good:
- examiner or assessor: ‘Is there anywhere else you might think of looking?’
- candidate pauses: ‘…can’t think of anywhere…’
- examiner or assessor: ‘Are there any other checks you wish to make?’
- candidate: ‘I don’t think so…’
It is very easy to lead the candidate - they must come up with the answers, not the examiner or assessor. In the examples above, the good prompts alert the candidate for more information, but do not tell them what to look for. The bad prompts virtually give the answer to the candidate, which examiners or assessors must be mindful not to do. Your prompting, in most cases, will control the candidate’s actions and responses and ultimately influence the overall decision of the test.
5.08 Health and safety considerations
Examiners and assessors must wear fluorescent vests at all times when outside of the office.
The examiner or assessor must manage the environment in which the test is being conducted. The candidate should be encouraged to use personal protective equipment if they have such items, especially when moving around and under the vehicle edges or compartments. Given the physical nature of this test, the vehicle will generally pose a potential for injury if a candidate does not act correctly. If there is the possibility of a candidate getting burnt or injured when opening an access panel, bonnet, or engine cover, the examiner or assessor must act quickly to verbally remind them to take extra care. Examiners and assessors should be vigilant and ever-mindful of the overall working environment.
Examiners and assessors should stand in the best possible position they can in order to keep proper control of the test and be able to hear what the candidate is saying, balanced against health and safety considerations. For example, on an LGV test, it is best to talk to a candidate who is seated in a cab through the open window of a closed door.
Some questions ask the candidate to start the engine. A candidate may also wish to make a rolling brake check. In these cases, the examiner or assessor must keep full control of the situation. Do not stand in front of or behind a vehicle when the candidate is expected to start the engine.
5.09 Preparation for the test
Required items
The examiner or assessor should take on test the following:
- iPad (External assessors CPC 4)
- paper contingency test report
- pass certificate book (DVSA11)
- fire extinguisher picture card and any other picture card(s) relevant to the combination being used
5.10 Meeting the candidate
The examiner or assessor should ask for the candidate by name, greet them pleasantly and then carry out the same licence and email check and identification procedures as laid out in chapter one.
5.11 Pre-brief
In an effort to create a more relaxed and informal atmosphere during the test, examiners and assessors are encouraged to introduce themselves and use the candidate’s first name, provided there’s no objection.
The following is a usable example:
My name is XXX. Would you like me to give you brief information regarding the test? … This is the practical demonstration test. Would you like me to give you a brief overview of the test?
If the candidate says yes, then a “brief” explanation can be given. For example:
The test will last about 30 minutes and when we get to the vehicle, I will ask you questions based on five set topic areas. I would like to emphasise that this is a demonstration-type test, therefore when I ask you questions, I will be looking for you to demonstrate your knowledge and understanding.
At the vehicle
Now I should like to ask you some questions relating to your vehicle; remember, it is important that you demonstrate your responses, and not just tell me what you would do.
5.12 De-brief
At the end of the test, the examiner or assessor should offer the candidate a de-brief, which is intended to give an overview of their performance.
A de-brief on a pass should concentrate on praising the topic areas in which the candidate did well and point out any areas (if any) where there was a slight weakness.
For failed candidates, the examiner or assessor should refer to the digital test report/CPC4 and comment very briefly on the topic areas where performance was unacceptable, making reference to reading the topic overview(s). For tests conducted on CPC4, the candidate MUST be issued with the CPC4C copy, which includes a statement of failure, along with some other useful information.
If the candidate wants to discuss the test in greater detail, it should be explained that examiners or assessors are not permitted to do this. However, to be helpful, the examiner or assessor should suggest that their comments about the items marked be relayed (by the candidate) to their instructor, who should be able to provide the detail required.
Examiners and assessors must avoid being drawn into discussion on specific questions. Candidates should be encouraged to read the explanatory markings and to research appropriate resource materials. The DVSA official guides (publications) “Driving Buses and Coaches,” “Driving Goods Vehicles,” and “Driver CPC for Professional Bus and Coach Drivers” contain all necessary learning resource materials to be successful in the module four practical demonstration test.
If the instructor/trainer/accompanying driver is present for the decision and de-brief, the examiner or assessor should ask:
Would you like your instructor/trainer/accompanying driver to be present for the conclusion of the test?
If the instructor/trainer/accompanying driver is not present, the question should not be asked.
If at any time the instructor/trainer/accompanying driver comes over to the vehicle to listen to the conclusion of the test, and a de-brief is to be given, the examiner or assessor must ask the candidate whether they want their instructor/trainer/accompanying driver present.
If the candidate elects not to have their instructor/accompanying driver present for the decision and de-brief, then the examiner or assessor should ensure that the candidate’s request is complied with.
If in exceptional circumstances, an examiner or assessor decides not to give an explanation, full reasons for the decision should be noted on the digital test report or CPC4. Where a candidate refuses the de-brief, the examiner or assessor should give their opinion as to why, or any explanation given by the candidate, on the digital test report or CPC4. The “de-brief” box on the digital test report or CPC4 should accordingly not be marked.
If a candidate argues or becomes abusive, or so upset that an explanation is obviously of no value, the examiner or assessor should abandon the attempt and a brief note should be made on the digital test report or CPC4..
5.13 End of test
Module four is not a licence acquisition test. Therefore, the candidate’s driving licence must not be taken from them under any circumstances. If a licence were to be shredded, the candidate would have to apply for a replacement licence.
5.14 Minimum driving age and young drivers scheme
Driving of vehicles in categories C and D at the age of 18
The Drivers Certificate of Professional Competence (CPC) directive 2003/59/EC ( as retained ) makes provision for driving at the age of 18 under certain controlled conditions. .
The minimum age to drive vehicles in categories C and D is reduced to 18 where the person driving:
- has a CPC qualification authorising the driving of a vehicle in that class
- is authorised by a document showing participation in a national vocational training (NVT) course to drive a vehicle in that class
- is taking lessons as a provisional licence holder and/or taking a licence acquisition test to drive a vehicle in that class
6. General technical matters
6.01 General guidance
This chapter contains advice and guidance on a variety of associated operational matters and circumstances. Any enquiries should be made to the technical standards team:
Technical Standards
technicalstandards@dvsa.gov.uk
6.02 Test programmes
Test candidates are assigned to programmes electronically by TARS (Testing & Registration System). Each programme must be allocated to the examiner named on the journal. Examiners must have access to their LDTM’s Outlook calendar and should make every effort to contact them for any test transfer approval.
6.03 Yellow exclamation ‘check’ indicator on digital journal
Digital journals are visible a day prior to the test. If there is a ‘Check’ marker against a booked test, the examiner should contact the examiner help line as soon as possible. Exceptionally, if the examiner cannot get through, for example, a late change journal received for an out of hours test, they should proceed with the test as usual and carry out the check on the following working day.
For a check on a digital journal, the examiner must access the additional information page of the digital journal by selecting the candidate’s name. This may still require the examiner to contact the examiner helpline as soon as possible as above.
6.04 Appointment confirmation
Customers don’t need to bring their appointment notification to the test centre. Customers making a booking via the internet aren’t given the choice of a postal appointment confirmation. Their only choices will be an email confirmation or no confirmation required. This means there’s a risk that not all candidates will have an appointment notification to take with them to the centre.
Previously, the appointment notification asked candidates to take it with them to the centre. This had been used as contingency, particularly for out-of-hours (OOH) tests where there is no admin support available. In these circumstances, if the candidate’s name doesn’t appear on the journal, the examiner may use the e-mail confirmation as part of his decision-making around whether the test should be conducted or not.
During working hours, examiners can contact the contact centre for clarification of who should be taken on test. Currently, for OOH tests (weekends and evenings), if more than one candidate arrives for the same slot, and neither are on the journal, the one with the confirmation would be taken out. If neither has a confirmation, the examiner must decide who to take out and inform Support Services the next working day.
6.05 Procedure if candidate details aren’t showing on the journal
During working hours: In the event that more than one candidate arrives for the same slot, examiners should contact the examiner hotline for clarification about who should be taken out on the test.
During OOH Periods: In the event that more than one candidate arrives for the same slot, examiners should decide who to take out on the test and inform the Support Services team the next working day.
6.06 Test transfer guidance - DL91 electronic test transfer request
Test candidates are allocated to programmes electronically by the Testing & Registration System (TARS). Each programme is assigned to a specific examiner.
When informing Deployment of the test transfer, at least 10 minutes notice should be given when available, to allow for journals to be updated. If less than 10 minutes notice is given due to a very late swap then, for digital tests, a paper test report must be used and rekeyed upon completion against the correct candidate on the iPad. When any test transfer has been actioned, you must check that the correct candidate details are on the digital journal. If not then a paper test report must be used and rekeyed. If test transfers cannot be actioned in time for the digital journal to be updated then Deployment will inform the examiner / LDTM to complete the test on a paper test report and rekeyed.
A request for a test transfer must be made by using the electronic test transfer request form on SharePoint in the Driving Examiner Documents section. All information must be fully completed, clearly indicating who the donor and recipient examiners are in all instances. This will prepopulate the electronic DL91 Test Transfer Log.
Without exception, all test transfers must be authorised by an LDTM or above. Where a manager is not available to authorise the transfer of the test, a transfer can be instigated by the staff member in consultation with Deployment; however, it is the staff member’s responsibility to ensure the line manager is informed as soon as possible. For each transfer, please complete all fields; giving details of the requesting person (name and grade).
It is not possible to list all of the reasons why a test should or should not be transferred. All staff should be mindful that, with the exclusion of tests transferred due to sickness or management activity, any transfer is an exceptional event and not a common occurrence. Security and integrity of the test are of the utmost importance.
In all circumstances, any test transferred between examiners for any reason must be recorded on the electronic DL91.
In all circumstances, each transfer should be recorded individually on the electronic DL91 by the examiner requesting the change; showing the donor, recipient and application reference for each customer.
6.07 Residency declaration
The 185-day residency requirement applies to all candidates who apply for a GB provisional licence before they attend to take a test. If the candidate refuses to sign, the test must not be conducted.
Candidates who present for an extended test do not have to satisfy the residency requirement.
If, during the test, the candidate made it clear that they had signed the residency declaration in error and wished to retract it, the test would need to be terminated as the candidate would no longer satisfy the residency requirement.
The test would be recorded as a code 70 – candidate refused to sign the residency declaration and the examiner should make a comprehensive note of the circumstances on Digital Test Report.
The candidate shouldn’t be questioned along these lines during the test as this could distract them and affect their performance. Once the test has started, any discussion regarding residency requirements must only be done at the end of the test and not during it.
6.08 Expired photos
The photograph on a photocard driving licence expires after 10 years, although in most circumstances, the entitlement to drive remains (until aged 70) even if the photograph has expired. DVLA writes to all licence holders when their photograph expires advising that they must get a new photo to update their photocard driving licence. However, there may be occasions where a candidate presents for a test with an expired photograph on their photocard driving licence. In these circumstances, the following procedures should be followed:
- Candidate arrives for test with an expired photocard driving licence and the examiner is satisfied that the photograph is a true likeness of the candidate; the examiner should take the test. If the candidate fails the test, they should be advised to apply to DVLA to have their photocard licence updated. If the candidate passes, the examiner should return the licence and advise them, they will need to apply to DVLA for their new photocard licence
- Candidate arrives for test with an expired photocard driving licence, but the examiner is not satisfied that the photograph is a true likeness of the candidate. The examiner should not conduct the test and should advise the candidate to apply to DVLA and update their photocard licence
6.09 Passports
Candidates are only required to provide a passport to support their identity where they have a British or EU old-style paper driving licence. The passport does not have to be a UK passport, but holders of non-UK passports should check that they are eligible to take a driving test here. For those taking the ADI test of instructional ability, the trainee licence is accepted instead of a passport. If the candidate does not have the correct documents, then he/she will not be able to take the driving test and may lose their booking fee.
Note: Photocopies and screenshots/scans of documents are not acceptable if they are the only form of ID. If a test is not conducted, a full report of the circumstances should be made on the Digital Test Report.
6.10 Theory certificates
The regulations give examiners the discretion to proceed with a test where evidence of a TT pass is available, even if the certificate is not produced. That discretion must be exercised reasonably, taking into account the circumstances of the particular case.
In case of an integrity marker on the journal, the examiner must contact Customer Services to establish if there is a valid Theory Test certificate on record. If there is no valid Theory Certificate on record, then the candidate must produce the original document or a duplicate copy issued by DVSA as a pdf (this can be printed or presented electronically) at the start of the test, but the examiner must see the accompanying email from DVSA. If there is no evidence of a theory test pass, the test should be terminated.
6.11 Change of name or gender
If the candidate’s name or gender differs from the details on the journal or their driving licence, the examiner needs to discretely establish their identity. If the examiner is satisfied that the identity of the candidate is correct, the test can continue without the need to see any supporting evidence such as a marriage certificate, divorce papers, deed poll, or a gender recognition certificate. However, if the identity of the candidate can’t be established, the test can’t proceed. In this instance, advise the candidate to visit the GOV.UK website www.gov.uk/change-name-driving-licence, which covers changing the name or gender on the driving licence.
In all instances of a change of name or gender, the ADLI (Automated Driving Licence Issue) route cannot be used.
6.12 (Removed for security reasons)
6.13 Candidate’s driving licence and insurance
If it becomes apparent during the test, e.g., from police enquiries, that the candidate’s driving licence or insurance is not in order, the test should be terminated, and a note made in the additional comments section of the Digital Test Report.
6.14 Northern Ireland licences
Northern Ireland licences have an 8-digit driving licence number. They are not eligible for the ADLI route; successful candidates must have their licence returned to them.
Northern Ireland ordinary driving licences and LGV drivers’ licences, full and provisional, are valid in Great Britain. Full licences may be exchanged for equivalent British licences without the need to pass a test.
Note: Northern Ireland licences issued prior to 1989 had no provision for a signature but do have provision for a photograph. If the candidate can be identified from the photograph, the test should proceed.
6.15 Identifying candidates wearing a hijab/niqab
The hijab covers the head; when the head covering is worn in conjunction with a veil, this is known as a niqab.
Whenever possible, a female examiner should request the removal of the niqab to verify the identity of the candidate. This should be done in a courteous manner with an explanation as to the purpose of the request.
If a female examiner isn’t available, the candidate should be asked if they would prefer a female ADI or a friend or relative to accompany them when the identification of the candidate takes place. This identification should take place, if possible, in a private area. If a candidate wearing a niqab refuses under any circumstances to reveal her face, examiners should advise the candidate that the test can’t be conducted and that they will lose their test fee.
6.16 Under-aged drivers
Where the journal or driving licence shows that the candidate is below the required age for the category of vehicle being used for the test, the examiner should make discreet enquiries, away from the waiting room area, to establish the correct age. If these enquiries confirm the candidate is underage, the test should be terminated.
However, examiners are reminded that the minimum age to drive vehicles in category F and AM is 16; and for category B (and B automatic) when the person is in receipt of the higher rate of Disability Living Allowance (or equivalent).
Where an underaged candidate is only discovered at the end of a passed test, the examiner should issue the DVSA10 without comment and report the matter to Support Services, who will inform MI and DVLA.
6.17 Eyesight
The eyesight test must be carried out in good daylight. Care should be taken to select a clean number plate on a vehicle, which can be clearly viewed. The candidate should first be asked to read a number plate containing symbols 79 mm high and 50 millimetres wide, which is obviously more than 20 metres away.
If the candidate is unsuccessful, they should be asked to read another plate and, if necessary, allowed to walk forward until it is just over the appropriate distance away.
If the second plate is not read correctly, the examiner must use the official tape to measure the precise distance from a third plate.
If the candidate fails to read the third plate, and the examiner is satisfied beyond doubt of their inability to comply with the eyesight requirement, they should be informed they have not reached the required eyesight standard, this means they have not passed, and the remainder of the test will not be carried out. Fail due to eyesight (code 3) should be recorded on Digital Test Report along with a note `Tape used’ showing size of symbol and measured distance inserted in the additional comments section of the Digital Test Report, together with the correct number and the candidate’s interpretation of it.
The D255 must be completed electronically and e-mailed to DVLA, copies are stored electronically for inspection by the LDTM. For Digital Test Reports, an end-of-test summary will be issued.
A candidate must never be asked to read a number plate at a distance less than 20 metres. If the candidate uses glasses to read a number plate and then removes them to drive, the examiner should point out that, if they can only read the plate with the aid of glasses, the law requires them to be worn whenever they are driving. If they subsequently take them off during the drive, they should be informed that unless they are worn when driving, the test will be terminated.
Note: If you are aware a candidate has dyslexia you should establish if any adjustments are required for the eyesight test. Black on Yellow is ordinarily easier to distinguish by most dyslexic candidates. They may also read back to front or in a non-uniform order and may have difficulty distinguishing between certain images, for example, B & 8, D & O, 5 & S. They may find it easier to write down the letters and numbers rather than reading them out - this is deemed to be a reasonable adjustment.
The eyesight test is a legal requirement, and the correct procedure must be carried out. However, providing the test is not undermined, examiners should exercise their judgement where the numbers or letters are ambiguous. The following advice may help examiners to deal with unusual situations:
If at any time prior to the eyesight test it transpires that a candidate is without their glasses, or has the wrong ones, they should be told that if they take and fail the eyesight test, their driving test will be terminated. If the candidate elects to continue the examiner should proceed with the test in the normal way. If the candidate attempts to read a number plate, with or without glasses, but is unable to do so, and then explains that they have either lost or broken their glasses or have brought the wrong ones, the test result must be recorded as termination - Code 82: Incorrect or No Lenses Worn.
If the light is suitable for testing but nevertheless cannot be considered `good daylight’, the candidate may, if necessary, be asked to read a number plate at the measured distance. However, if they cannot do so, they should not be regarded as having failed, and the test should be terminated (code 66) and the circumstances reported to Deployments.
Customers with a disability
In cases where a customer has a disability such as paraplegia, the examiner may need to adapt the process to ensure the eyesight test is conducted fairly and practically. For instance, the customer may be allowed to drive a short distance to position their vehicle in a suitable location for the test. In such situations, the examiner can conduct the eyesight test from inside the customer’s car to accommodate their needs while maintaining the required distance and standards.
Bioptic (Telescope) spectacles:
DVLA Drivers’ Medical Group has advised that bioptic devices are currently not acceptable for driving in Great Britain. Consequently, if a candidate attends for test with bioptic (telescope) spectacles, the eyesight test must not commence if they try to use one of these devices.
6.18 Special eyesight tests
At the request of DVLA, special eyesight tests are conducted on certain applicants for driving licences. LDTMs will carry out or will arrange for the tests to be carried out, in consultation with Regional Operations Support (ROS). The test to be administered is the eyesight test as carried out on a normal driving test.
6.19 Vehicle safety check questions
Before moving away, candidates must be asked one ‘tell me’ vehicle safety check question. Whilst on the move, candidates must be asked to demonstrate one ‘show me’ question. To ensure uniformity, the questions must be selected from those listed in the DT1. For the Digital Test Report, the ‘Tell Me’ question used must be recorded on the Digital Test Report before commencing the test report page. The ’Show Me’ question must be recorded on the Digital Test Report at the end of the test. As a general rule, the questions should be used in rotation. However, examiners will need to exercise common sense and discretion at times, for example, in deciding whether a question that involves opening the bonnet is appropriate in high winds or heavy rain. Examiners should choose a suitable road to ask the ‘on the move show me’ question.
Although some checks may involve the candidate in opening the bonnet to identify where fluid levels would be checked, candidates must not be asked to touch a hot engine or physically check the fluid levels.
6.20 Special needs – safety questions
Where a special need prevents a candidate from carrying out a practical activity for the ‘tell me’ question, they should be asked to demonstrate understanding by oral explanation. However, they should be expected to carry out the ‘show me’ question on the move. Reasonable consideration must be adopted in disability cases, and if adaptations do not allow candidates to operate all controls such as windows or demisters on the move an alternative question should be asked. Customers with adaptations need to be able to operate the horn and windscreen washer whilst driving as they are safety critical, they can also be used as one of safety the questions on the move.
6.21 Health and safety – hi-vis vests
Examiners must wear fluorescent vests (full jackets are acceptable but not mandatory) when asking the vehicle safety questions on the road. If necessary, candidates should be discouraged from standing in a vulnerable location (e.g., along the offside of the vehicle on a busy road) when carrying out these checks.
6.22 Interference with candidate’s vehicle
Apart from necessary adjustments, connecting the sat nav to the in-car power supply, or when assisting a candidate with a physical check of direction indicators, examiners must not operate or adjust the controls or fittings of a test vehicle. Other adjustments, including to dashcams, can only be made with the candidate’s agreement, by asking the accompanying driver to assist, or where it is essential to avoid danger to the occupants and general public or damage to the vehicle or property. The candidate may ask the examiner to assist in adjusting the nearside door mirror before a manoeuvre. The examiner should not refuse this simple request and assist the candidate as appropriate. The candidate should not have to lean across the examiner to adjust the mirror.
6.23 No valid MOT
If an examiner has suitable reason to doubt whether a vehicle presented for test has a valid MOT, then a check can be made using the Search DES App.
This check must not delay or impact the timing of the test, and examiners must not enter the car park/starting location prior to the test specifically to check vehicles.
If it is clear that the vehicle has no MOT, the normal terminated test procedure must be followed and activity code 21 recorded. If there is an element of doubt or a suitable explanation provided, then the test should not be terminated.
6.24 Rear view mirror requirements
The legal requirements on fitting of rear view mirrors, which are most likely to have a bearing on the conduct of tests, are set out below. They are minimum requirements, and, if an examiner is sure that a vehicle does not comply with them, they should terminate the test. The requirements do not apply to vehicles brought temporarily into the country by visitors or to vehicles in the service of visiting forces.
“Nearside” and “offside” means, respectively, the left and right sides of the vehicle regardless of whether it is right or left-hand drive.
From 1 April 2006, test vehicles used for large vehicle and vehicle-trailer combination tests (bus/lorry) and car plus trailer tests must be fitted with outside, nearside, and offside mirrors for use by the driving examiner during the test.
This includes practical tests to join the register of large goods vehicle (LGV) driving instructors.
Motorcycles, with or without a sidecar, do not have to be fitted with mirrors.
Vehicles first used before 1 June 1978 requires:
- motorcars: 1 external or internal
- goods vehicles and passenger carrying vehicles (PCVs): 1 internal or external nearside
Vehicles, including cars, goods vehicles, and PCVs first used on or after 1 June 1978 require:
- 1 internal (or one external nearside if internal mirror does not provide adequate view to the rear)
- 1 external offside
Goods vehicles exceeding 3500kg maximum authorised mass and large PCVs first used on or after 1 April 1983 require either:
- 1 internal or one external nearside (if internal mirror does not provide adequate view to the rear) and one external offside
- 1 external offside and one external nearside
Good vehicles exceeding 3500kg maximum authorised mass first used on or after 1 April 1985 require:
- 1 external offside and one external nearside
Note: Mirror cams are acceptable on test for LGV, PCV. The examiner should consider all normal requirements in regard to their own health safety checks and visibility.
6.25 Mirror safety
Internal mirrors must be surrounded by a material that renders the edges and the material unlikely to cause severe cuts if struck by an occupant.
6.26 Registration mark
The registration mark can be taken only as a probable indication of the age of a vehicle as it may have been re-registered.
6.27 Seat belts
Examiners must wear a seat belt when conducting a car test. When fitted, seat belts must be worn for all large goods vehicle (LGV) and passenger carrying vehicle (PCV) tests too. In LGV/PCV vehicles first manufactured with seat belts fitted, the candidate must wear the seat belt. If the seat belt has been removed or damaged to the extent that it cannot be worn, the test should be terminated.
Seat belts for the examiner and any accompanying driver must be fitted to lorries used for test, including with-trailer. Seat belts must be fitted to all buses used for test.
Although the seat belt regulations do not apply to older types of vehicles, examiners must wear seat belts, if fitted, on all LGV and PCV driving tests.
6.28 Problems with seat belts
If the belt is in proper working order but the examiner is physically unable to wear it, they should terminate the test and send a full written report to the LDTM. A belt may be dirty but still fulfil the legal requirements. An examiner should not terminate a test solely on the grounds that the seat belt is dirty. They should wear a dustcoat or weatherproof jacket to protect their clothing where it is reasonable to do so.
In rare cases a belt may be so filthy that protective clothing will not deal with the problem. If so, and as a last resort, the examiner may terminate the test. A full report of the circumstances should be made to the LDTM.
6.29 Wearing of seat belts by candidates and third parties
If the candidate does not wear their belt, the examiner should remind them that, unless they are medically exempt, the law requires the seat belt to be worn. If the candidate does not have an exemption certificate and declines to wear the seat belt, the test must be terminated. The circumstances should be reported on the DL25 or in the additional information section of the Digital Test Report.
Candidates are allowed to remove their seat belt whilst carrying out a manoeuvre which includes reversing.
When a third party accompanies a candidate on test (for example, an instructor or interpreter) and a rear seat belt is available and that person does not wear the belt, the examiner should ask the rear seat passenger to put it on. If the response is a negative one, it should be pointed out that for health and safety reasons and regulations they are required to wear a seat belt. If they decline to do so, the test will be terminated. In these circumstances, the third party has the choice of wearing the seat belt, not accompanying the candidate on test, or having the test terminated. In the event of a termination, a note of the circumstances should be made on the DL25 or in the additional information section of the Digital Test Report.
Should the ADI or accompanying driver choose not to and/or not be able to accompany the test, the examiner should ask the candidate if they would like them to be present at the end of the test for the result and debrief.
Examiners should be tactful, especially when dealing with a passenger who holds an exemption certificate (see below) and highlight the dangers of not wearing a rear seat belt.
Additional information on rear seat belt use:
- any rear seat passenger(s) accompanying an examiner during a driving test MUST wear a seat belt
- any rear seat passenger(s) refusing to wear a seat belt should not be allowed to accompany the examiner on the test—this includes a person who holds a seat belt exemption certificate
- if a rear seat passenger refuses to wear a seat belt (whether or not they hold an exemption certificate) and refuses to leave the vehicle, the test should be terminated
- should the ADI/accompanying driver choose not to, and/or not be able to accompany the test, the examiner should ask the candidate if they would like them to be present at the end of the test for the result and debrief
- when rear seat belts are not fitted to the vehicle, rear seat passengers must not be allowed to accompany an examiner on the test
6.30 ‘L’ (or ‘D’) plates in Wales
Regardless of whether the candidate holds a full licence in another category or holds an international driving licence, they must display Lplates on the vehicle during the practical test for the category they are being tested on. The examiner should explain that the regulations require the vehicle to display ‘L’ or ‘D’ plates that are clearly visible from both the front and rear of the vehicle.
Sets of ‘L’ or ‘D’ plates should be kept at the DTC and offered to the candidate for their use. The candidate should be given reasonable time to comply with the regulations. If they are unable to do so, the test should be terminated.
6.31 Set exercises
The Legislation requires we conduct two set exercises (one in reverse gear) on each test except Module 3b test. These may be conducted during the independent driving section of category B car tests but must not be conducted during the independent driving section of any other categories.
The two set exercises are a controlled stop and one of the following, which may be selected at random:
- reverse parking (either into a bay or on the road).
- forward parking (into a bay).
- pull up on the right and reverse in a straight line.
Examiners should ensure the random use of the reversing manoeuvres is evenly spread. Identifiable patterns (times, routes, and so on) should be avoided so that the random aspect of manoeuvre selection is retained.
A controlled stop must be carried out on every test.
To commence the angle start, the candidate first completes a controlled stop by pulling up on the left behind a parked car, reasonably close but not so close as to make it difficult to move away. The angle start exercise, therefore, combines 2 mandatory elements (controlled stop and moving away at an angle) as required.
The angle start (AS) box must be recorded on the Digital Test Report once the ‘controlled stop’ has been conducted on every test.
6.32 Emergency stop (cat B only)
An emergency stop should be carried out on one in seven of tests chosen at random. It can normally be carried out at any time during the test, but the emergency stop exercise must be carried out safely where road and traffic conditions are suitable. If an emergency has already arisen naturally during the test, this special exercise is not required; in such cases, the candidate should be told, and a note made in the additional comments section of the Digital Test Report.
With the vehicle at rest, the examiner should explain to the candidate that they will shortly be tested in stopping the vehicle in an emergency, as quickly and safely as possible. The warning to stop the vehicle will be the audible signal “Stop!” together with a simultaneous visual signal given by the examiner raising the right hand to face level, or in the case of a left-hand drive vehicle, raising the left hand. This should be demonstrated.
The examiner should explain to the candidate that they will be looking over their shoulder to make sure it is safe to carry out the exercise, and that they should not pre-empt the signal by suddenly stopping when the examiner looks round but should wait for the proper signal to be given. To minimise the risk of premature braking, examiners are advised to ask the candidate if they understand the ES instructions. The emergency stop must not be given on a busy road or where danger to following or other traffic may arise.
It is essential that examiners take direct rear observation to ensure that it is perfectly safe to carry out the exercise. They must not rely on the mirrors. If the exercise cannot be given within a reasonable time, the candidate should be asked to pull up, care being taken to choose the right moment as the candidate will have been expecting the emergency stop signal and may react accordingly. They should then be advised that the exercise will be given later and that they will be warned again beforehand. Alternatively, if conditions ahead are expected to be favourable, they should be reminded that the exercise will be given shortly, and the instructions repeated if necessary.
If a candidate asks whether they should give an arm signal, they should be told that the command to stop will be given only when it appears that no danger will arise as a result of a sudden stop, but that they should assume that an extreme emergency has arisen and demonstrate the action they would take in such a case. The emergency stop exercise must not be used to avoid a dangerous situation.
6.33 Normal stop and hill start
It is possible to include a normal stop or hill start at the pre-brief stage of the independent driving section. For example, when pulling into the left before the start of the independent drive itself, and/or between separate sections of the independent drive, e.g. when pulling the candidate up to give a further series of directions. For Digital Test Reports, NS and HS/DS must be recorded when a normal stop or hill start/designated stop has been conducted.
The candidate should be kept on route wherever possible. If a candidate is clearly reacting and planning for a junction but it appears they are taking the incorrect direction, examiners should give safe guidance as appropriate.
6.34 Independent driving - general instructions for all categories
Please refer to the sat nav SOP
Introduction
Independent driving has been introduced into all main categories of practical driving tests to help ensure instructors better prepare candidates for real driving conditions. It is not intended to make the test harder.
The candidate will be asked to complete a section of independent driving by following either:
- car tests: directions given by a sat nav, traffic signs or a combination of both for a minimum of 20 minutes or up to the duration of the whole test
- all other categories: traffic signs, a series of verbal directions, or a combination of both for approximately 10 minutes
During the independent section of a car test, all aspects of the tests, i.e. legal requirements, manoeuvre, ‘show me’ question, can be completed. For all other categories, angle starts, hill starts, normal stops, and if appropriate, bus stops can be completed.
Additional information
Any faults assessed in the independent driving section of the test will be recorded in line with the normal criteria as prescribed in the DT1 ‘guide to assessment and marking’.
It should be remembered that independent driving is a test of how the candidate uses their forward planning and multitasking skills. It is not testing the candidate’s ability to remember directions.
On occasions, the candidate may ask for the direction to be repeated or confirmation of direction - in both cases, the examiner should respond in a friendly, positive manner. This is not a ‘prompt’ as the candidate will have instigated the query themselves in confirming/planning for the junction ahead.
A test should not be terminated, or a failure recorded simply and only because a candidate cannot follow the independent drive instructions.
However, in extreme and exceptional examples of the candidate having difficulty, the examiner can curtail the independent driving section and continue using normal directions.
This should be noted in the additional information section of the Digital Test Report.
Pre-brief
It is important that the candidate is left in no doubt about what is required in the independent driving section of the test.
There are 3 methods of independent driving for car tests: following directions given by a sat nav, following traffic signs, or a combination of both (blended route), and 3 methods for all other categories: following traffic signs, a series of verbal directions (supported by a diagram), or a combination of both.
When required, the examiner should pull the candidate up on the left and clearly explain the method to be followed. Stopping for the pre-brief may be utilised as a normal stop or hill start, providing the road conditions permit and the correct wordings are used.
Cat A - examiners should tell the candidate that if they forget where they were asked to go, they should simply pull up on the left at a safe place, and the examiner will join them (the same as if there is a problem with the radio).
Cat C and D - examiners may, when using the following traffic sign method and providing the road is safe to do so, commence the independent driving section on the move. This does not apply when issuing a series of verbal directions supported by the diagram.
Sat nav
The candidate should be asked to follow directions given by the sat nav. If the candidate requests that the audible directions be turned off, they should not be refused.
The examiner will operate the sat nav and select ‘drive’ when the independent driving section is about to commence.
If the candidate inadvertently goes off route, the sat nav may automatically redirect back to the route. However, if this is unsuitable or impractical, then the examiner should take control and direct the candidate appropriately.
Traffic signs
The candidate should be asked to follow traffic signs, for example, ‘follow the signs for A1 Edinburgh’, which could become ‘now follow the signs to Bathgate please’.
There is no need to stop the candidate to change directional signs as long as it is safe and appropriate.
Direction changes should not be given while driving in hazards, such as at junctions or when negotiating oncoming traffic, and so on.
Blended route
There is no need to stop the learner driver to change from sat nav directions to traffic signs during the blended route.
Verbal directions: (not applicable to category B car tests)
The candidate should be given a series of directional instructions verbally, for example, ‘at the end of road turn left - at the roundabout turn right third exit - take the first road on the left’.
Whilst giving the directions, the examiner should ask the candidate if they wish to see a diagram. The examiner may also ask the candidate to repeat back the instructions.
This process should be repeated with each new series of verbal directions.
No more than three changes in direction should be given at any one time. However, four are acceptable in exceptional circumstances, such as when the instructions are particularly straightforward.
For example, ‘at the end of the road, turn right, ahead at both mini roundabouts, at the end of the road, turn left’.
Combination of traffic signs and verbal directions (not applicable to category b car tests)
The procedure is the same as set out above for each method.
There is no need to pull the candidate up when linking between the verbal directions and following traffic signs, as this can be done on the move.
However, before issuing verbal directions (supported by the diagram), the candidate must always be stationary in a safe and appropriate place on the left.
End of independent drive
The candidate should be informed when the independent drive section has been completed.
This can be done whilst the vehicle is moving, but again care should be taken with the timing of this instruction in relation to hazards.
Diagrams (not applicable to category B car tests)
Diagrams supporting the ‘verbal direction’ method are intentionally basic and simply show the general direction of travel.
They are not maps and are not intended to be to scale.
The diagrams do not stand alone, and examiners should, when issuing directions, do so in conjunction with additional detail when appropriate, such as:
- ‘Follow the road ahead; it does bend quite sharply. At the end of the road, turn left.’
- ‘Just follow the road - it is quite a long way. When you get to the traffic lights, turn right.’
- ‘It’s the exit after the supermarket.’
The diagrams form part of the route sheet, and the master copies are retained electronically on SharePoint alongside the associated route.
Diagrams should always be printed on the pastel paper provided and not on white paper (following advice from the British Dyslexic Association).
Examiners may include reference to appropriate landmarks in the verbal directions when showing the candidate the diagram.
For example, ‘end of this road, turn right, then take the next road on the left just after the big cinema, and then ahead at the roundabout’.
Diagrams should not be altered or adapted for general use (see the section below on disability, special need, language).
Although where required, in order to help the candidate visualise an instruction, a simple written prompt may be placed on the diagram - for example, ‘petrol station’.
Examiners should ensure that a ‘clean’ diagram is used for subsequent tests.
Disability, special needs and language – independent drive
Some disabilities may affect a candidate’s ability to read traffic signs, whilst for others following a series of verbal directions could be difficult. If a disability or special need is declared at the time of booking, the examiner’s journal will be annotated accordingly. (DVLA does not require form D255 for deaf, dyslexic, or dyspraxia candidates, unless there is a further associated disability.)
Where a disability or special need is declared or is apparent, and providing the test is not undermined, examiners should, wherever possible, adapt their approach to accommodate the candidate.
Some candidates might feel the need to use a variety of coping strategies when driving independently. This should be allowed wherever possible, without comment, and their driving performance assessed in the normal way.
When informed (either by the journal or personally) that a candidate has a special need such as dyslexia or dyspraxia, examiners should tactfully establish how severely this affects them when following directions.
In these cases, examiners should ask the candidate which is their more able method: following directions given by a sat nav or following traffic signs. Therefore, if examiners are made aware prior to the test commencing, they should carry the sat nav and peripherals to cover each scenario. Examiners should be prepared to:
- when using a traffic sign route, write down place names if the candidate is struggling to understand the place name
- limit the verbal direction section to just two instructions at one time. (Not applicable for car tests.)
- on the verbal direction pre-brief, suggest if it helps that directions can be given as ‘next side’ rather than ‘left’ or ‘right’, for example, ‘at end of road turn to my side, take the next road to your side and at the roundabout take the exit to your side. So, (showing diagram) that’s end - my side, then turn - your side, roundabout - your side. Can you repeat that please’? (Not applicable for car tests.)
- include appropriate landmarks in the verbal directions when showing candidate the diagram, for example ‘end of this road turn right, then take the next road on the left just after the big cinema, and then ahead at the roundabout’. (Not applicable for car tests.)
- if considered necessary to help the candidate visualise an instruction a simple written prompt may be placed on the diagram, for example ‘petrol station’. (Examiners should ensure that a ‘clean’ diagram is used for subsequent tests.) (Not applicable for car tests.)
6.35 Satellite navigation systems on test (non-DVSA supplied)
Satellite Navigation systems (Sat-Nav) already present in the test vehicle: Use of satellite navigation in-car is becoming more and more common. Some are after-market fit; some are built in to the vehicle from new. These devices are allowed to be working (switched on) during a driving test provided the sound and any audible alert system do not cause any distraction. If the test will include independent driving delivered by means of a DVSA supplied sat nav, the examiner should explain the confusion that could be caused with two devices on display, and allow the candidate to switch off / remove the non-DVSA device. Occasionally, the positioning of an after-market device in a vehicle may not be ideal. Examiners should use considered judgement before asking for a device to be repositioned. We must not give the impression the use of such a device is unwelcome but should offer assistance if the presence of such a device may confuse the candidate
6.36 Test routes
The LDTM is responsible for quality control of test routes at centres they manage and must ensure content is regularly reviewed. Test routes must be recorded in accordance with the standard operating procedure.
The completed test routes should be stored by the LDTM in the Driver Training and Tests SharePoint site. The LDTM should ensure, so far as is practicable, that examiners conduct tests over approved routes, unless exceptional circumstances arise which make it necessary to curtail or deviate from the set route. He/ she should also ensure that any deviation on the route is fully reported in the additional information section of the Digital Test Report.
LDTMs are responsible for ensuring that examiners conduct tests that comply with statutory minimum test time requirements as laid out in the DT1.
The choice of which route to use should normally be left to individual examiners. The HEO should, however, ensure that examiners use an even spread of routes so that testing is not concentrated in particular roads or areas. The aim must be to minimise nuisance and inconvenience to local residents. For category B car tests, each driving test centre should have 12 routes. Examiners should utilise the routes evenly over time. This can be monitored using MI information and reading of Digital Test Reports and write ups.
Local authority traffic regulation orders may sometimes have an adverse effect on test routes or parking facilities near centres. If this is known in advance, the Agency can make representations to the local authority and may be able to secure some modification of the proposals so as to lessen their effect on testing operations. HEOs should therefore look out for any notice or reports about such proposals which may affect their own or other centres, both L and LGV, and encourage their examiners to do likewise.
6.37 Routes
Test routes are laid out and approved by the LDTM and should be adhered to. Whilst maintaining an element of urban driving in test routes, as much use as practicable should be made of available opportunities for driving on roads with national speed limits, including rural roads and dual carriageways.
Main category tests should include a section of independent driving nominated on the test route. This section should be closely monitored by the LDTM to ensure suitability.
Wherever possible, LGV/PCV test routes should provide a test of ability to negotiate a reasonably severe downhill gradient.
If, exceptionally, it is necessary to curtail or deviate from an approved route, a note of the circumstances should be made in the additional information section of the Digital Test Report. In considering possible alternatives, examiners should bear in mind that:
- Roads with very steep gradients (more than 12%) should not normally be used.
- Candidates should not be taken where road signs or markings are not readily followed.
- In the case of LGV and PCV tests, a very serious situation could develop if a candidate were directed to take a road which proved unsuitable because of insufficient headroom, weight restriction, or any other impassable hazard, and where the opportunity to turn back was too difficult to attempt or non-existent.
Vehicles with a maximum speed of not more than 25mph must use warning beacons when being driven on unrestricted dual carriageways. Such roads should not, therefore, be used for conducting tests with tractors or other slow-moving vehicles.
6.38 Motorways
Every effort must be made to prevent learner drivers from joining a motorway. If a learner driver joins a motorway, the test should continue to the next exit if safe to do so, and a test pass should be awarded if the learner driver completes the rest of the test to the required standard, including all legal requirements.
Stopping on the emergency area or hard shoulder should only be considered as a last resort if it would clearly be unsafe to continue to the next exit.
6.39 Tests conducted on a motorway
Regulations differ between England and Scotland regarding what categories of vehicle may be driven by a provisional licence holder on a motorway. Highway Code Rule 253 provides summary information.
Tests conducted in England and Wales
The following categories are the only tests we can conduct on a motorway:
- Cat C
- C+E
- C1
- C1+E
- D
- D+E
- D1
- D1+E
Tests conducted in Scotland
The following categories are the only tests we can conduct on a motorway:
- Cat C
- C+E
- D1
- D1E
- D+E
C1/C1E are not allowed on test on a motorway.
6.40 Advisory speed limits
Advisory speed limits are often used in particularly sensitive areas, such as outside schools, where it is considered that a reduction in speed would benefit the immediate community. They are there to encourage people to drive at a lower speed than they might otherwise do.
In common with assessing all other driving situations, examiners must:
- assess whether the driver’s actions are safe.
- not automatically record a fault if the driver does not rigidly comply.
In some instances, there may be mitigating circumstances, such as:
- in school holidays or at quiet times of the day, where there are very good fields of vision and low pedestrian activity, and safety is not compromised.
- however, there will be instances where exceeding advisory limits could not be considered safe.
Sometimes, especially in narrow residential streets, the driver may need to reduce their speed considerably lower than the advisory limit.
6.41 Test terminated at candidate’s request
Examiners should avoid giving a fail disclosure to a candidate before a test has been fully completed. There are circumstances, however, where a candidate insists on knowing if they have failed or not before the end of the test; usually after realising they’ve committed a serious fault.
If pressed, the examiner should tell them but should do their best to manage this kind of situation and continue as normal unless the candidate requests the test to stop. Divulging a failure can demoralise the candidate and/or cause further poor driving or an insistence they don’t want to go any further. The latter can cause additional problems, as the candidate rarely understands the test stops at this point and the car moves no further (other than to find a safe location to terminate); a problem if positioned a long way from the test centre.
If the candidate elects not to continue, the test is terminated and Activity Code 5 recorded with details recorded in the additional comments section of the Digital Test Report.
6.42 Dangerous driving by candidate
There will be occasions when a candidate’s driving on test becomes so dangerous that the safety of the public, the examiner, and/or the candidate is threatened. In these circumstances, the examiner should stop the test.
The examiner should issue a statement of failure and tell the candidate that the test has been stopped before completion for reasons of public safety. In any case, completion of the test would have made no difference to the decision. A note of the circumstances should be made on the Digital Test Report.
6.43 Terminated tests - procedure
Once the examiner decides that a test must be terminated, they should bring the test to an end as soon as it is safe to do so. The examiner should direct the learner driver to stop in a safe location and explain why the test has been terminated. Examiners must not drive the vehicle back to the driving test centre and must not direct or guide the learner driver to continue driving back after the decision to terminate the test has been made.
When tests are terminated with or without a result on the Digital Test Report:
- the appropriate termination code must be selected and a description of the circumstances written in the additional information section
- the digital Journal will be annotated with the appropriate code after completion.
- the Terminated Test Log (TTL) must be completed
- the TTL must state ‘Digital Test Report.’
6.44 Terminated tests – returning to the test centre
If a test has to be stopped away from the test centre, offers to return the examiner to the test centre by an accompanying driver/ADI should be accepted.
If the accompanying driver is not present, the examiner should suggest to the candidate that they might prefer to return to the centre with them. However, if the candidate is adamant they don’t want to return with the examiner, their wishes should be respected.
The safest and most convenient method of returning to the test centre must be sought. Every effort should be made to help a disabled candidate to return to the centre, possibly by calling a taxi or telephoning the centre for assistance.
On return to the test centre, the examiner should contact the accompanying driver as quickly as possible.
Examiners must not drive candidates’ vehicles. Strict observance of this instruction is essential as there are many situations in which insurance cover for the examiner might not be effective. Candidates are rarely familiar with details of motor vehicle insurance conditions or in a position to give the necessary permission. In any case, only third party risks might be covered. Similarly, an examiner’s own motor insurance policy may not provide full cover when they are driving someone else’s vehicle even with the owner’s permission.
6.45 The extended test
Drivers convicted of certain dangerous driving offences are required to take a mandatory extended driving test following a period of disqualification; these will be identified on the journal. The procedure for conducting these tests is the same as for any other driving test with the following exceptions:
On meeting the candidate, the examiner should, in the pre-brief, inform the candidate that the test will take approximately 70 minutes and will be conducted on a variety of roads including those where the national speed limit applies
The emergency stop exercise must be carried out on every test
20 minutes independent driving (in line with category B test)
Successful candidates should be issued with a DVSA10 certificate.
The length of the driving part of the extended test is prescribed in Regulations as being of not less than 60 minutes duration. Examiners must note in the additional information section of the Digital Test Report, the time the candidate first moved off and the time the candidate returned to the test centre and stopped the engine. Examiners are advised to use the timer at the top of the test report page.
6.46 Unaccompanied drivers driving away from the DTC
If someone drives away unaccompanied after failing their test and you consider this to be an illegal drive-off, then you could report this to the police.
6.47 Illegal parking
If the candidate seeks to pull up where the vehicle would be infringing waiting restrictions or any other legal requirements, the examiner should point out that they would be breaking the law by doing so; usually, it would be better to intervene so as to enable the candidate to reach a place where they can pull up legally.
6.48 Parking before the test
If a candidate tells the examiner that the car is parked some distance away, the examiner should accompany the candidate to their vehicle, provided that they can do so and reach a test route in time to complete a normal test. If, however, from the description of the parking place the examiner is satisfied that this would not be possible, the time factor should be explained to the candidate and the test should not be conducted. If this situation arises when a candidate arrives late for their test but is not so late as to involve cancellation for that reason alone, the examiner will need to take account of this additional factor in deciding whether or not the test could be conducted.
An examiner may sometimes find the candidate’s vehicle parked in a position from which they consider that only an experienced driver could move it safely. If the accompanying driver is available, they should be asked to move the car to a more suitable position. Otherwise, the examiner should ask the candidate if they are prepared to drive the car away and, if so, the test should proceed, and a note made in the additional information section of the Digital Test Report. If the candidate is not prepared to move the car, the test should be terminated.
6.49 Candidate suspected of being under the influence of drink or drugs
Where an examiner has good reason to believe, either before or during the test, that a candidate is under the influence of drink or a drug so that it is likely to affect the control of the vehicle, they should inform the candidate that they appear to be ill and that, in fairness to them, the examiner feels unable to take or continue the test. The examiner will need to use considerable tact in announcing this decision and must avoid making any reference to drink or drugs.
6.50 Candidate ill
If a test candidate decides that they are too ill to take or continue with a test, the examiner should terminate the test. However, an examiner should not terminate a test just because they consider a candidate is too ill to continue unless this is affecting their ability to drive safely or they are informed they have an infectious disease. A list of infectious diseases can be found at UK Health Security Agency. Pregnant examiners should follow guidance in the staff handbook and ensure they are aware of any additional risks.
6.51 Candidate in advanced stage of pregnancy
Occasionally candidates in an advanced stage of pregnancy present themselves for a test.
Examiners may find the following advice helpful:
Examiners should not ask the candidate whether they are pregnant, as this can lead to an embarrassing situation if the candidate is not. It is the candidate’s responsibility to ensure they are medically safe to carry out all the requirements of the test.
If the candidate raises concerns over carrying out some aspects of the test (emergency stop for example), the examiner should tactfully mention that, in view of her condition, certain difficulties might be encountered during the test, referring in particular, to the emergency stop. The examiner should make it clear that they are quite prepared to conduct the test and should not try to influence the candidate’s decision in any way. If the candidate decides not to continue, the test should be terminated, and a report made in the additional information section of the Digital Test Report.
The emergency stop must not be excluded from the test purely on the basis that the candidate is pregnant. Normal test procedures (that is, one in three tests should contain an emergency stop) should apply.
6.52 Instructors or friends- during the test
Car tests
In the waiting room, examiners ask candidates if they would like to have their approved driving instructor (ADI)/accompanying driver with them for the test, test result, and end of test de-brief. The accompanying person must be at least 16 years of age. The examiner should where necessary tactfully explain the third party must not interfere with, or comment on the test, without giving the impression the third person is not welcome.
If an ADI is known to regularly observe their pupils on test, it’s not necessary to comment.
Note: The general guideline is that only one accompanying driver is allowed on a driving test. However, in exceptional circumstances, 2 accompanying drivers may be permitted as a reasonable adjustment to accommodate specific needs.
Motorcycles
If the candidate requests their instructor/accompanying rider to accompany them on the test, it should generally be encouraged, but examiners using their own personal car may decline such a request. If a hire car is being used, DVSA has no objection, as the insurance would cover passengers. Following a bike-to-bike test is permitted, providing the third party is on another bike and there is no interference with the conduct of the test.
During Module 1 motorcycle tests, instructors/accompanying riders are not permitted on the MMA.
LGV/PCV
If the candidate requests their instructor/accompanying driver to accompany them on the test, it should be encouraged, providing a suitable seat is available. If there isn’t a seat available, they can observe the safety questions, but they will be advised to stand outside the manoeuvring area to observe the reversing and un-coupling/re-coupling exercises. Instructor/accompanying drivers will be invited to listen to briefings and end of test de-briefs, but they will need to supply and wear hi-viz whilst on the manoeuvring area.
Note: The general guideline is that only one accompanying driver is allowed on a driving test. However, in exceptional circumstances, 2 accompanying drivers may be permitted as a reasonable adjustment to accommodate specific needs.
6.53 Interpreters accompanied driving instructor
Driving test candidates can no longer use foreign language interpreters on their test. A driving test can only be conducted in either English or Welsh language.
An interpreter may accompany deaf and/or deaf without speech candidates for tests conducted in English or Welsh only. The interpreter must be at least 16 years of age. If a signer is present, it might be convenient to allow them to sit in the front of the car to explain the examiner’s requirements. This will normally only be necessary at the beginning of the test. In any case, the interpreter should occupy the front seat only when the vehicle is stationary.
6.54 Discussion with candidates and third parties
Candidates who fail the test are naturally disappointed and may express dissatisfaction either with the test itself or with the manner in which it was conducted. This situation requires most careful handling; complaints about driving tests sometimes originate from comments made by examiners either gratuitously or in repartee to candidates at the time of the test or later.
Examiners must avoid commenting on motoring matters, driving or instructional techniques, or on any articles, books or illustrations dealing with driving or instructional techniques. Apart from the oral explanation of faults to candidates at the end of a test, examiners must on no account discuss driving tests in general, or details of particular tests, with candidates or third parties; nor must they suggest to a third party that individual candidates would benefit from professional tuition.
6.55 Testing of personal friends or relatives
It is a long-established principle in the Civil Service that an officer should not put themselves in a position where official duty and personal interest conflict.
Testing of personal friends:
If an examiner finds on their test programme a candidate who is a personal friend, or anyone else whose test they consider it would be unwise to conduct, they should at once inform the LDTM who may decide to transfer the test to another examiner. If the position affects the LDTM, the ODM should be informed.
Testing of relatives:
Testing of examiner’s relatives should be conducted in the first instance by the LDTM or higher grade regardless if the examiner taught them. Exceptionally, if a senior officer is not available, a substantive LDTM from an adjacent test centre should be approached to conduct the test provided the LDTM has no personal connection with the candidate, the candidate’s relatives or the instructor.
Testing of DVSA employees
Tests for DVSA employees should normally be conducted by a staff instructor or an examiner at HEO grade or above. If this is not possible, advice must be sought from the Chief Driving Examiner or their Deputy.
6.56 Relations with driving schools and instructors
In accordance with the Civil Service Code of Conduct and the Agency’s guidance on personal relationships at work, advice is provided in areas where personal relationships overlap with working relationships. This ensures that DVSA staff maintain the expected standards of behaviour and do not leave themselves open to allegations of impropriety, bias, abuse of authority, or conflict of interest.
During official hours, relationships with instructors from any field, such as car, LGV/PCV, or motorcycle, should remain pleasant and courteous, rather than friendly and familiar. Examiners should limit interactions to a polite acknowledgment or greeting in the waiting room or casual remarks to pass the time of day. Conversations with instructors should be avoided beyond these interactions. Any approaches from instructors involving complaints or enquiries, other than routine matters, should be referred to the Higher Executive Officer (HEO).
The agency does not wish to interfere with examiners’ private lives; however, a close association or friendship with an L, LGV/PCV, or MC instructor can raise doubts about an examiner’s impartiality when conducting tests. This could be construed as improper conduct, and attention is drawn to the general principles on conduct outlined in the staff handbook.
Examiners who find themselves involved in or developing an association or friendship with an instructor outside official hours must inform their HEO of the situation at an early stage. This notification should be made in writing to line managers, and written confirmation of this knowledge should be provided to the examiner concerned. This correspondence must be copied to the Senior Executive Officer (SEO) to take the necessary steps to avoid potential embarrassment to the agency.
New entrant examiners must relinquish any ties with a driving school. If any relative, including a partner, is involved with a driving school, the situation must be reported to line managers.
Additionally, you must inform your Line Manager if any relationship develops, as this could compromise the rules of the Civil Service Code.
6.57 Driving instruction by examiners
Examiners must obtain authority from their Higher Executive Officer (HEO) before giving driving instruction to anyone. If the person concerned is a member of the examiner’s immediate family, authority will not normally be withheld. However, authority for instructing other individuals should not be granted automatically. Proper consideration must be given to each case, ensuring there is no potential for financial or other gain to the examiner, and that the situation would not embarrass the Agency.
In all cases where authority is given, the HEO must be informed of the starting and finishing dates of the instruction. Additionally, it must be ensured that the examiner does not conduct the driving test of their pupil. The HEO should be notified when a member of an examiner’s family is taking a test, so that an independent examiner can conduct the test.
Examiners are prohibited from seeking or accepting any payment, either in money or in kind, for driving instruction or any related service, such as acting as an accompanying driver or providing a vehicle.
6.58 Gifts or offers of gifts from candidates
Examiners must not accept gifts, money, or any benefit from candidates, driving instructors, driving schools, or their representatives, as well as any other member of the public with whom they come into contact during their official duties. Accepting gifts can be perceived as a bribe and may compromise, or appear to compromise, an examiner’s official position. If a gift of any kind is offered before, during, or after a driving test, the examiner should immediately inform the candidate that their instructions require them to report the matter.
If a gift or offer is made during the test, the examiner must terminate the test and complete a full report of the circumstances to be sent to the Local Driving Test Manager (LDTM), who must then report it to the Police, the Senior Executive Officer (SEO), and DVSA’s Counter Fraud and Investigations Team. If a gift is offered before a candidate who has failed receives the statement of failure, the examiner should complete the statement, hand it to the candidate, and report the incident as described.
In cases where a gift is offered after a pass certificate has been issued, the examiner should follow the same protocol. Although it is unlikely that the candidate will persist, if they do, a full report should be sent to the LDTM, who must then report it to the Police, the Operations Delivery Manager (ODM), and DVSA’s Counter Fraud and Investigations Team.
Casual gifts, such as those offered at Christmas, even if not connected with official duties, should be politely but firmly declined. If received through the post, they should be returned with a covering letter from the LDTM.
Similar caution applies to offers of hospitality, which should generally be refused to maintain independence and impartiality. Acceptance of hospitality could create obligations or be misinterpreted, compromising the examiner’s position. If anyone with whom examiners might have official dealings persists in offering gifts or hospitality, the matter should be immediately reported to the ODM. Examiners uncertain about the propriety of accepting hospitality should consult their LDTM.
Any attempt by a member of the public to offer a gift or reward, with the intention of obtaining a concession or recognising a service, such as a favourable decision on a test, must be reported immediately to the LDTM. The LDTM should then report the matter to the ODM, the Police, and DVSA’s Counter Fraud and Investigations Team.
In cases of suspected corruption, the agency will take all possible action, including involving the police, to investigate the matter. Failure to comply with these instructions could have serious consequences, including dismissal and prosecution.
6.59 ADI and PDI certificate numbers
Examiners should inform their LDTM and complete the appropriate form if it comes to their attention that an ADI’s or PDI’s certificate is out of date or illegible, so that the correct enquiries can be made and if necessary, enforcement procedures started.
ADI certificates are not legally required to be displayed during a driving test. If the certificate is displayed and an examiner needs to remove it from its holder, they should try to avoid causing damage to either the certificate or its holder.
6.60 Unregistered driving instructors and concerns about instruction standards
In the normal course of their duties, examiners become familiar with the driving schools and ADIs who regularly bring candidates for tests, including the vehicles they use. Certain patterns may raise concerns, including:
- the reappearance of an unfamiliar accompanying driver or an unmarked car fitted with dual controls, especially where no ADI certificate or trainee licence is displayed
- a consistently poor standard of candidates presented by a particular instructor or driving school
Examiners must not engage in enforcement or investigative activity. They must not question candidates or accompanying drivers, nor make comments that imply doubt about the legitimacy or quality of instruction received.
If an examiner suspects that unregistered instruction is taking place, they should report the matter to their LDTM. The LDTM should gather and forward all available evidence (e.g. test reports, vehicle details, witness accounts) to the Counter Fraud and Investigations team.
If an examiner has concerns about a consistently poor standard of instruction, they should also report this to their LDTM. The LDTM can report consistent poor instruction to the ADI Enforcement Manager for the area.
6.61 Adverse weather conditions
Examiners have responsibility to decide in bad weather whether it is safe to conduct tests. For example: snow, ice, fog, or high winds etc. Deployment and the centre HEO must be informed of the position at the earliest time. Examiners should take into account the health and safety of both the examiner and the candidate when deciding if the test should proceed. In addition, motorcycle examiners must ensure that road and MMA conditions are safe for riding.
It may be necessary to inspect the routes to decide whether conditions are acceptable. Examiners should consider whether conducting a test or tests in the circumstances is in the best interests of public safety and a fair assessment of a candidate’s driving performance. Where a test cannot go ahead, candidates who arrive for test, or enquire by telephone, should be informed that tests will not be conducted. At sites that provide facilities for motorcycle training to take place on the MMA, it is the ATB instructor’s responsibility to make a decision on whether they consider the site to be safe to conduct the training session where there is no DVSA staff presence on site at the time of the training. Where a DVSA examiner is present, a decision can be made on the safety of the site, thus overriding any decision made by the attending ATB Instructor. Where this is so, instructors and candidates who arrive for training sessions, or enquire by telephone, should be informed that sessions will not be conducted.
If it seems that conditions may improve, those with appointments later in the day should be advised to enquire again later. Candidates who arrive at the centre should be advised to expect a new appointment automatically. In the event of prolonged interruption of tests by snow or ice, examiners should follow the advice on the intranet. Deployment and the sector HEO should be kept fully informed of disruption to programmes due to weather conditions and also informed when testing recommences. If a candidate telephones the centre to say that weather conditions near their home are too bad for driving, the examiner should tell them that the Agency will postpone the test and that they will receive a new appointment in due course.
6.62 Bad weather guide for examiners
Preparation of bad weather - journals
Digital Test Report and Journal: Once deployment is informed of cancelled tests due to bad weather, the digital journal will be updated, and a manual activity code should not be necessary. In these cases, the candidate cannot be rebooked later that day. If there is a possibility that the candidate can be rescheduled for later in the day, inform Deployment at the time when informing of the original cancelled test slots. This will allow for the candidate to be moved automatically on the digital journal. Activity code 61 should only be input on the Digital Test Report if, on the following day, the test is still active on the previous day’s journal. Full guidance is on SharePoint in the Bad Weather section.
Weekend OOH Cancellation due to Bad Weather: Contact Deployment if available and follow the process above. If Deployment is not available, then do not submit any cancelled test information until the end of the day or until it is apparent that no further testing will commence. These tests must still be submitted for activity codes to be processed. This will allow the potential for a candidate to return later in the day and the test to be conducted on the iPad and also will allow for the automatic rebooking to take place, if not conducted on the day.
Candidate Contact Details on the Journal: Candidate contact details are on the journal meaning that they can be contacted directly to tell them that the test won’t be going ahead. If this is the case, deployment needs to be aware that this is happening. Make sure customers contacting test centres for advice about appointments receive an appropriate response. When testing has been suspended, a member of staff should be present to offer appropriate advice to customers phoning or attending the centre.
When adverse weather prevents access to the centre, the answer machine should provide customers with the most up-to-date information. The message should say:
Thank you for calling the ***** driving test centre. As of today (insert date), due to the bad weather, this test centre will be closed. We hope to continue testing at (time) on (date), but this will be subject to improvements in road and weather conditions. Your test will be rebooked automatically, and a new date will be sent to you. Thank you.
Candidate Can’t Get to the Centre but the Centre is Open: Candidates may ring the test centre in cases where there is bad weather at their home, and they can’t travel. The answer machine should give them the option to leave a message. When completing the Digital Test Report, use activity code 62, so a free rebooking can be made. The examiner should regularly refresh their journal to ensure the details have been updated.
6.63 Under-age passengers and service/therapy dogs
Tests should not be conducted with persons under the age of 16 years or animals in the vehicle. An exception can be made for designated service or therapy dogs.
6.64 Candidates attending for test wearing a Kirpan
The Kirpan is an ornamental dagger and is one of the 5 articles of faith worn by an Amritdhari (Baptised) Sikh. This can be worn under or over clothing and is usually contained within a holster or case. As the Equalities and Human Rights Commission and the Criminal Justice Act 1988 safeguard the rights of Sikhs to carry the Kirpan as part of their faith, the candidate should not be asked to remove or cover up the Kirpan for the purposes of the driving test.
6.65 Undeclared disability
If the examiner notices that the candidate may suffer from some restriction of movement, which could be classed as a disability, make discreet enquiries at an appropriate opportunity. In the case of physically disabled persons, examiners should ask about any adaptation(s) fitted to the vehicle and how they operate in relation to the disability. This information should be recorded in detail in the additional comments section of the Digital Test Report and will be helpful in completing the D255. Care should be taken when the test is accompanied to obtain permission from the candidate before discussing disability issues.
6.66 Examiners conducting driving/riding tests in Welsh (all categories)
At centres in Wales, when a test is pre-booked in Welsh, examiners should ensure that the Welsh Digital Test Report is active and the appropriate language selected, and if applicable a Welsh pass certificate issued.
When a test has commenced in English because the candidate did not apply for it to be conducted in Welsh, and it becomes apparent to the Welsh-speaking examiner that the candidate would prefer for the test to be conducted in Welsh, then the examiner should continue with the English Digital Test Report, and select the appropriate language section when back in the office, to record that they conducted the test in Welsh in the interest of customer service.
At the end of the test, and if applicable, the examiner may offer an English or Welsh pass certificate to the candidate.
Welsh Digital Test Reports should only be used for tests that have been pre-booked in Welsh.
6.67 (Removed for security reasons)
6.68 Mobile phones/tablets on test
In an effort to keep distractions to a minimum on test, all parties present in the vehicle must either turn off their mobile phone/tablet device or ensure they are set to silent mode.
Before the test on-road section begins, the examiner must:
- make sure their mobile phone is on silent or switched off.
- ask all other parties present to set phones/tablet devices to silent or turn them off.
The examiner must manage this carefully. There is no objection to an accompanying driver using a tablet device or smartphone to take notes whilst on test, providing the device is on silent and does not distract the examiner or the candidate audibly or visually (the latter may be by window reflection).
If an examiner feels that the use of an electronic device is causing undue distraction, they can ask for the device to be switched off. A decision to terminate a test must only be considered after every effort is made to ensure compliance with these instructions. Should the test be stopped, a full report of the circumstances must be written in the additional information section of the Digital Test Report.
Devices must not be used for any recording purposes, either video or audio.
6.69 DVSA policy on the filming of driving tests
Filming of driving tests is limited to the following circumstances:
- filming by external parties, for example, TV production crews with the agency’s permission, with the agency having editorial control of the film - conducted for promotional or educational programmes
- filming by DVSA officials for promotional or educational purposes for internal/external customers
DVSA does not allow the recording or filming of the conduct of any theory or practical test activity. This includes recording or filming by use of any internal-facing equipment fitted to any type of test vehicle. Examiners must not operate or adjust the controls or fittings of a test vehicle, which includes dashcams, except with the candidate’s agreement. If required, ask the accompanying driver to make any necessary adjustments.
DVSA is aware that customers may have external-facing cameras fitted to their vehicle (some for insurance purposes) and these are generally acceptable. However, external-facing cameras fitted to a motorcycle instructor’s motorcycle cannot be used when they are observing an accompanied motorcycle test. Rearward-facing cameras on a candidate’s motorcycle are also not acceptable. If it becomes evident that any equipment is filming an examiner conducting a test either visually or audibly, and it can’t be switched off, the test will not continue.
DVSA will not under any circumstances accept, comment on, or review audio/video media provided by a test candidate or third party to facilitate a challenge to the conduct of any theory or practical test or its result. Any footage received in connection with an allegation of criminal activity or intent will immediately be referred to the police.
6.70 Officers of the agency
Except for driving examiner staff with technical responsibility for the conduct of tests, no officers of the agency, or anyone else, should accompany candidates unless they have first received specific authority from the chief driving examiner or their deputy. Non-operational personnel should be asked to withdraw if a candidate objects to their presence on the test.
6.71 Quality control or assurance of tests
Candidates are required by regulation to allow an authorized person to accompany the examiner for quality control or assurance purposes.
- If the candidate objects, the accompanying officer should ask the reason and may decide not to go on test if there are special circumstances, for example, there is no third seat, or the candidate has been accompanied on a previous test.
Otherwise, they should:
- explain to the candidate the need for quality control or assurance to ensure, in the interests of all candidates and the public at large, that arrangements for tests are satisfactory and in accordance with regulations.
- quality control or assurance officers should also mention the legal situation and that the test will be terminated unless the candidate agrees to their presence.
If the candidate persists in his objections:
- the test should be terminated, and the circumstances reported in the additional information section of the Digital Test Report
- tests may be quality controlled by operations directorate operational managers and quality assured by Quality Leadership Team. They must use their discretion as to the tests on which they accompany examiners
The procedure to be followed is set out below:
The quality control or assurance officer should tell the examiner beforehand that they propose to accompany them on the test and should be present when the examiner meets the candidate.
When the examiner has completed the preliminary test procedure, they should say to the candidate:
‘(Name of candidate)…………… colleague will be coming with us on the test and will sit in the back of the car and take no part in the conduct of the test.’
In the case of a large goods vehicle (LGV) test, the examiner should first ask the candidate if his cab will hold three people.
- Officers intending to quality control or assure a test should not do so in cars where a rear seat belt is not available.
At the end of an accompanied test, following the comparison of faults recorded by both officers, and any discussion to resolve differences, quality control or assurance officers should:
- make their quality monitoring form available to the examiner who conducted the test who should sign it to indicate that they are aware of the contents
- the Digital Test Report should be marked in the appropriate box
6.72 Quality control assessments
An LDTM is required to carry out a minimum of 4 quality control assessments annually on each permanent examiner at their centre(s). Regular visiting examiners should also be assessed as necessary. These should be spread proportionately over the year between all disciplines conducted by the examiner, ensuring all disciplines tested are assessed.
In the case of new entrants, it is important that instructions laid down in the new entrant development plan are adhered to, and the appropriate supervision is conducted. Where examiners have taken on new skills, the LDTM must ensure that adequate development and quality control takes place to ensure new skills are consolidated.
6.73 Quality control or assurance of visiting examiners
To comply with normal procedures and customer service standards, it is important that all examiners are quality control assured regularly. When an examiner spends considerable time at another centre other than their own, either conducting car, motorcycle, large goods vehicle (LGV), or passenger carrying vehicle (PCV) tests, then the LDTM at that centre should carry out quality control after consultation with the visiting examiner’s own LDTM. At LGV centres where there is a LDTM, they should quality control examiners but not those LDTMs who are either stationed there or are visiting on detached duty.
For the same reasons, it is equally important that examiners who are employed on a part-time basis are regularly quality controlled. Quality control officers should make themselves aware of when these examiners are working within their area of responsibility and make the necessary arrangements for carrying out quality control.
6.74 Scrutiny of test documents and reports
All completed test administration must be accurate. Regular checks of all driving test documentation and Digital Test Reports should be made to ensure consistency of assessments and that the report reflects the assessment made.
6.75 Test centre log sheets and records
Monthly:
- terminated test log
- test Transfer Log
- Spoilt certificate log
6.76 Centre records
Examiners are responsible for registering and controlling stocks of pass certificates. A pass certificate register book (not a loose leaf type) must be maintained showing the serial numbers of the pads of forms held in stock. The book should contain records of all types of pass certificate used at the DTC. Certificates must only be issued in serial number order. For security reasons, the register must be kept securely and separately from the stock of certificates.
Receiving examiners should sign the register to confirm receipt. Any imperfect or spoiled certificates should be destroyed at the test centre using the shredder. The certificate numbers should be entered onto the spoilt certificate return form and submitted by email to support services: spoilt.certificates@dvsa.gov.uk at the end of each month. If certificates have been lost or stolen, the matter must be notified to Operations immediately by email.
6.77 Ministerial correspondence
If a Member of Parliament writes directly to a driving test centre, the correspondence should immediately be scanned into a DVSA iPad and emailed to: chief.executive@dvsa.gov.uk, to be dealt with in the normal way for Ministerial correspondence. If the letter suggests that a report will be required from an examiner and/ or the HEO, this should be put in hand in anticipation of the formal request from the Chief Executive Team.
6.78 ADI meetings – attendance
HEOs may be asked to attend local driving instructor meetings and can do so on a voluntary basis provided they take place during the working week. The frequency of attending this type of meeting should not be more than once annually unless exceptional circumstances such as a test centre closure require an additional meeting. Your local ADI Enforcement Manager should be informed.
Meetings should be attended, chaired, and properly organised. It should be made clear that HEOs will not discuss individual cases or details of particular driving tests. HEOs should report back to their SEO any unusual questions and answers and provide a general overview of the meeting. HEOs should carefully consider their answers where questions are submitted beforehand and, if in doubt, discuss them with their SEO. Policy issues should not be discussed.
6.79 Detached duty/permanent transfer
When examiners visit from other centres on detached duty or permanent transfer, the LDTM must ensure that time is planned for H & S briefing, any induction, and centre familiarisation etc. Short-term deployments will be given periods to learn a sufficient number of routes. Longer-term detachments may require more route learning time.
6.80 Site access managers
At centres where a Site Access Manager (SAM) works, either yourself or any of your staff should:
- ensure that all paperwork is securely stored in the pre-defined location. Specific site details can be found on SharePoint
- for all DVSA locations, ensure that any site-specific issues around test delivery are dealt with on the day
- for non-DVSA sites, minor fuel spillages are treated in the same way as at a normal DVSA site, using the Oil Spill kits that are available
- ensure the SAM reports incidents to Interserve on the HS5, leaving a copy for the LDTM in a pre-arranged place
- ensure that the DVSA Health & Safety team are aware of relevant incidents
- not interfere with SAM completing their duties, unless the SAM is failing to carry out their duties effectively. In such cases, the LDTM should highlight failings to the SAM and report to the Interserve Helpdesk
- provide test centre facilities to the SAM to allow them to complete their duties, as agreed locally
7. Particular types of vehicle and adaptations
7.01 Suitability of vehicles for category ‘B’ tests
The vast majority of hatchbacks, saloons, and estate cars are suitable for tests, but increasingly, the designers of cars are producing models with sweeping lines which have good forward vision but have large blind spots to the rear and present examiners with problems of observation.
Other examples of vehicles not suitable for tests include:
- a vehicle with a gear that will not remain engaged
- a seat from which the examiner does not have a proper view
- ii one or more external lights are not working - but this does not include the high-level brake light if both obligatory stop lamps are working
- airbag warning light displayed
- passenger airbag, where fitted, switched off
- reversing lights are not working (vehicles first used after 1st September 2009 only)
- a draw-bar vehicle more than 18.75 metres long
- a vehicle running on a space saver tyre or any wheel/tyre of a different size on the same axle
- an engine MIL that shows there’s a malfunction is a major defect and applies to;
- petrol vehicles with 4 or more wheels, not more than 8 passenger seats and first used on or after 1 July 2003
- more than 8 passenger seats and first used on or after 1 July 2008
- gas and bi-fuel vehicles with not more than 8 passenger seats and first used on or after 1 July 2008
- diesel vehicles with 4 or more wheels and first used on or after 1 July 2008
Panel vans also present problems with vision and are unsuitable for tests. Vehicles supplied by motor manufacturers have obviously been through the type approval process, but this approval concentrates on vehicles from a driver’s point of view and such a process does not make the vehicle suitable for the purposes of the test.
7.02 Left-hand drive vehicles
Examiners should bear in mind that a candidate driving a left-hand drive vehicle should exercise special care, and make full use of the mirrors when about to overtake other vehicles or change direction to the right.
7.03 Hire cars on test
It’s the customer’s responsibility to ensure that the vehicle presented is insured for the purposes of the test.
Arnold Clark, who operates in Scotland and Northern England, has confirmed their dual-controlled cars are fully insured for the purposes of practical testing; their vehicles are easily identified by the livery.
Generally, other hire car companies make it clear in their terms and conditions that their vehicles mustn’t be used for training or testing and that their vehicles aren’t covered by insurance for these purposes.
Examiners should be aware that these other hired vehicles aren’t always easy to identify.
Category B - licence acquisition tests and ADI part 2 tests
If it is clear that the vehicle presented for test is a hire car without dual controls, the test must be terminated.
If it is clear that the vehicle presented for test is a hire car with dual controls, the test can go ahead.
If the examiner discovers it was a hire vehicle (non-dual controlled), when the test is completed, the examiner will be considered to have acted in good faith. Therefore, any subsequent claims can be managed under the Motor Insurance Bureau procedure.
Lorry and bus
Training companies hiring commercial vehicles will do so under their existing insurance policies and therefore hire vehicles are suitable for lorry and bus tests.
7.04 Vehicle recalls
Contact: technicalstandards@dvsa.gov.uk with any enquiries.
Each time an updated list of recalls is produced, it should be printed off for the use of examiners in the office.
There is a separate poster for the test centre notice board which provides general information about recalls, signposts customers to the up-to-date information on GOV.UK, and encourages ADIs to sign up for email alerts for news about new recalls.
The poster won’t need to be updated each time there is a new recall and should be placed in space 7 of the test centre notice board.
When a candidate presents for a test in a vehicle covered by a recall/safety notice requiring remedial action, no free re-test should be offered unless the information has been placed on GOV.UK up to three days before the test date.
7.05 Vehicles with automatic transmission
A vehicle with automatic transmission is defined in regulations as:
A vehicle in which the gear ratio between the engine and the wheels can be varied only by the use of the accelerator or brakes.
In general, a vehicle without a manual clutch is regarded as an automatic. The following points of driving technique are common to all automatic systems:
- the parking brake should be applied for temporary stops, for example, waiting at a red traffic light, a junction, or in a traffic hold-up, if they are likely to be of a long duration
- short stops may not require the application of the handbrake
- the handbrake may need to be applied to prevent ‘creep’. Faults committed in these cases should be recorded at handbrake
- the use of the right foot for both brake and accelerator pedals has considerable safety advantages. It is therefore recommended practice for normal driving, but is not necessarily applicable to disabled drivers. The use of the left foot on the brake pedal should not however be marked as a fault unless it involves the use of the footbrake against the accelerator
- the use of both feet when manoeuvring in a confined space is acceptable if carried out correctly, i.e., speed is properly adjusted so that no large throttle opening or heavy braking pressures are involved
- any fault should be recorded at footbrake and/or accelerator or in the ‘control’ box if it occurs in the reversing, reverse parking, or turn in the road exercise
7.06 Particular driving systems
Fully automatic system
This type has selector settings for forward and reverse, neutral and/or park. It also has settings which enable the driver to select and retain a particular gear ratio or range of gear ratios, for example, to obtain engine braking when descending a steep hill, although gear changes are normally made automatically. Most automatics of this type enable the driver to make an immediate change into the lower gear, to obtain extra acceleration, by means of `kick down’ or part throttle operation actuated by the accelerator pedal. In nearly all cases, the selector lever is mounted on the floor or the steering column in the position normally occupied by the gear lever, but there are exceptions, for example, a panel of press buttons on the facia.
Semi-automatic systems
With these, the driver has to select the gear required by movement of the gear lever as with a manually controlled gearbox, but there is no clutch pedal. For driving test and licensing purposes these vehicles are regarded as automatics.
Pre-selector systems
In these, the gear is selected before it is required by manual movement of a selector lever, which is normally mounted on the steering column. When required, the gear is engaged by a single depression and release of the gear-change pedal, which is situated where the clutch pedal would be on an orthodox transmission.
7.07 The clutch and Guidosimplex
These adaptations enable a vehicle to be driven in manual or automatic mode. The candidate can choose which mode to drive the vehicle in and if successful should be issued with the appropriate DVSA10.
Disabled candidates may use the vehicle for a test in automatic mode as a means of overcoming their disability. If successful, the candidate should be issued with a restricted licence in the usual way.
7.08 Centrifugal clutches and free-wheel devices
Vehicles fitted with these devices do not fall within the definition of vehicles with automatic transmission. The use of a free-wheel device or centrifugal clutch in addition to a pedal-operated clutch is at the discretion of the candidate.
7.09 Electric vehicles for test
A wide range of electric vehicles are now on our roads, from motorcycles to cars, buses, and commercial vehicles. Any vehicle presented for test must meet the Minimum Test Vehicle (MTV) requirements. This applies equally to electric vehicles.
These vehicles do not have a conventional gearbox or means by which the driver can disengage the engine from the transmission (clutch). They are therefore categorised as automatic transmission and are perfectly acceptable for test provided they meet the MTV for the category of test they are presented for.
7.10 Hill assist
A Hill Assist system allows a driver, when moving off on an uphill or downhill gradient, a couple of seconds to move their foot from the footbrake to the accelerator before the device releases the footbrake automatically. If this device is fitted drivers still have to co-ordinate the controls and take the correct observation when moving off; consequently, vehicles fitted with such a device are suitable for the practical driving test.
7.11 Electronically operated parking brake (handbrake)
Vehicles fitted with an electronically operated parking brake are suitable for use during a practical driving test. There are usually two ways of releasing an electronically operated parking brake:
- by depressing the footbrake whilst releasing the parking brake, then coordinating the accelerator and clutch to move away.
- coordinating the accelerator and clutch and when the electronics sense the clutch is at biting point, the parking brake releases automatically. The parking brake will not usually release automatically if the accelerator is not used or the controls are not coordinated correctly.
Providing there is no loss of control either method is acceptable. If an examiner needs to take action to stop the vehicle, if the electrically operated parking brake is applied and held on when the vehicle is in motion, it will bring the vehicle to a controlled stop.
7.12 Vehicle self-parking feature
Car manufacturers are now producing vehicles with ‘self-parking’ features, which when activated, automatically steer the vehicle into a parking bay or space by the kerb. This technology is becoming more common and it is likely that some of these vehicles will eventually be presented for test.
If any vehicle fitted with a ‘self-parking’ feature is presented for test, the test should be conducted in the normal way. However, vehicles fitted with these electronic devices must be capable of being switched off/de-activated when carrying out manoeuvres. Candidates must complete their manoeuvres manually. Vehicles with parking distance sensors are acceptable as this is merely a safety feature.
7.13 ABS - Anti-lock braking system
ABS is fitted to most vehicles. Examiners should not enquire if a vehicle presented for a test is fitted with ABS. Most ABS systems require the clutch and footbrake to be depressed harshly at the same time to brake in an emergency situation; therefore, a fault should not be recorded purely for using this technique with a vehicle fitted with ABS on the emergency stop exercise. On the emergency stop exercise, under severe braking, tyre or other noise may be heard. This does not necessarily mean the wheels have locked and are skidding. Examiners should bear these points in mind when assessing the candidate’s control during this exercise. Further advice regarding ABS is given in the DVSA publication ‘’The Official DVSA Guide to Driving – The Essential Skills’’.
7.14 ABS light
Examiners can make the decision not to take the test if it is on at the start of the test; however, if it comes on during the test, they should continue and the ADI or accompanying driver informed upon return.
7.15 Engine malfunction indicator lamp (MIL)
If the MIL illuminates part way through a test and the vehicle appears to be performing normally with no obvious signs of malfunction, then the test should continue and the ADI or accompanying driver informed upon return. If the MIL light becomes flashing amber or red during the test, the test should be terminated at the next safe opportunity.
Note: A defective MIL is not applicable to motorcycles. Kit cars, amateur-built vehicles, and American pickups are not required to be fitted with an engine MIL.
Many vehicles are fitted with warning lights to indicate that a service is due and so on. These warning lights are purely to remind the driver/ rider of the need to book their vehicle in for service and so on. Examiners must not terminate a test purely because this type of warning light is displayed.
7.16 Tyre pressure warning lights
Some vehicles have a warning system which indicates tyre pressure may be low. If the warning light is showing, examiners should carry out a brief visual inspection of the tyre and give the candidate or accompanying driver every opportunity to rectify any problems, they should bear in mind the principle that no test should be turned away that could reasonably go ahead. A test must not be terminated just because the tyre pressure warning light is showing.
7.17 Use of lights
Drivers are required by regulation to switch on their lights in conditions of poor daytime visibility. These are defined as ‘such conditions adversely affecting visibility (whether consisting of, or including, fog, smoke, heavy rain or spray, snow, dense cloud, or any similar condition) as seriously reduce the ability of the driver (after the appropriate use by them of any windscreen wiper and washer) to see other vehicles or persons on the road, or the ability of other users of the road to see the vehicle.’
If candidates are uncertain about switching lights on in conditions of poor visibility, or at lighting up times, examiners should remind them about this and, if necessary, advise them on how to operate the appropriate controls. If the examiner operates a switch, care should be taken to avoid physical contact with the candidate. An assessment will need to be made of whether to mark `ancillary controls’. If a candidate switches on lights in conditions which do not seem to require them, the examiner should not comment.
7.18 Automatic door locking mechanism
Before these devices are allowed to be fitted to vehicles, they must have “type approval.” Part of the approval is that the mechanisms unlock automatically in the event of a severe collision. The emergency services state that they can easily enter a car to rescue the passengers whether or not the doors are locked.
All vehicles fitted with automatic door locks can have the mechanism disengaged by a switch.
Examiners need to be sensitive when dealing with drivers who prefer to drive with the doors locked.
The police often advise that drivers, particularly females, should drive in town with the doors locked.
8. Candidates with a disability, health condition or learning difficulty
8.01 Physical disabilities
In common with other applicants for driving licences, those who are physically disabled have to take a test of competence to drive. The test requirements are generally the same as for non-disabled candidates, and the same test documents are used. In addition, the examiner must complete a report on form D255.
Where a candidate has a disability or special need, examiners should, wherever possible, adapt their approach to accommodate the candidate and accept any coping strategies used, providing the test is not undermined.
If the examiner notices during the test that the candidate may suffer from some restriction of movement which could be classed as a disability, make discreet enquiries at an appropriate opportunity.
In the case of physically disabled persons, examiners should:
- enquire about any adaptation(s) fitted to the vehicle
- ask how they operate in relation to the disability
This information should be recorded in detail in the appropriate box on the Digital Test Report and the D255.
8.02 Restrictions
The only cases where a restriction, other than the appropriate category letter, may be indicated on a pass certificate are those of candidates with a physical disability, which affects their ability to drive. Restrictions must not be related to a specific make of vehicle or machine, or to horse-power, cubic capacity, or un-laden weight.
8.03 Time allocated for test
More than one test period is normally allocated for an L test for a disabled person because of the extra documentation involved. Extra time can be allowed for candidates who are deaf without speech or who have declared a severe degree of deafness.
If a candidate in one of these categories fails to declare their disability when applying for the test, only one period will have been allowed. The test should, however, be conducted, the documentation being left for completion later in the day if necessary.
8.04 Independent drive section
Where a disability or special need is declared or is apparent, and providing the test is not undermined, examiners should, wherever possible, adapt their approach to accommodate the candidate and acknowledge any coping strategies used. Please see the chapter on General Matters, Independent Drive Section for full explanation.
8.05 Successful candidates
If the examiner is satisfied that the candidate is competent to drive all un-adapted vehicles in the category on which they were tested, and in any additional categories covered, a normal pass certificate for the category should be issued.
If the examiner considers that the candidate can drive un-adapted vehicles only of the category on which they were tested, but not the additional categories covered, then the pass certificate should be issued for that category (for example category B) and the D255 should indicate that the candidate should be restricted to category B vehicles.
If the examiner considers the candidate can drive only a vehicle with suitable adaptations, this should be indicated on the pass certificate. The appropriate restriction code (listed below) should be entered on the DVSA10.
8.06 Guidance to unsuccessful candidates
Generally, the candidate should be given the result of the test, and be given an oral explanation of faults in the usual way. The examiner should not make any remarks, or enter into any discussion, about the candidate’s licensing entitlement. However, if the examiner thinks some, or further, adaptation of the vehicle might enable the candidate to pass the test, they may give a general indication to that effect.
If a candidate asks for advice as to the precise manner in which they should adapt the vehicle, they should be referred to The Forum of Mobility Centres.
Website: www.mobility-centres.org.uk
8.07 Licence restriction codes
Code:
10 – Modified transmission:
- automatic selection of gear ratio
- adapted transmission control device (e.g., a button selector for moving up and down the gear range)
Note: Code 10 should be applied rather than code 78 when the driver needs automatic selection of gear ratio/modified transmission. Code 78 would be applied as an administrative code if the driver simply passed their test in an automatic rather than in a manual car.
15 – Modified clutch:
- adapted clutch, for example, a hand lever on the gearstick
20 – Modified braking systems:
- adapted, sliding or tilted brake pedal
- brake pedal suitable for use by left foot
- hand or knee operated brake
- adapted parking brake
- brake system operation supported by external force
25 – Modified accelerator systems:
- adapted or tilted accelerator pedal
- hand or knee operated accelerator
- accelerator pedal on the left
- accelerator operation supported by external force
31 – Pedal adaptations and pedal safeguards:
- extra set of parallel pedals (extension pedals)
- pedals at (or almost at) the same level
- any measure to prevent obstruction or actuation of accelerator and brake pedals when pedals not operated by foot (pedal guards)
32 – Combined service brake and accelerator systems:
- combined accelerator and service brake system operated by one hand
- combined accelerator and service brake system operated by external force (e.g., an electric gas & brake system – EGB)
Note: When there is a need for hand controls, if there is no restriction in the movement of the upper limbs, code 20 and 25 should be chosen rather than code 32 for combined braking and accelerator controls. This will then not limit them to a combined adaptation in the future – their need is for an adapted accelerator control and an adapted braking control, not for a combination of the two.
33 – Combined service brake, accelerator and steering system:
- combined accelerator, service brake, and steering system operated by external force with one hand (e.g., a four-way joystick)
- combined accelerator, service brake, and steering system operated by external force with two hands (e.g., a tiller steering system with integral accelerator and braking system)
35 – Modified control layouts (light switches, windscreen wiper, washer, horn, indicators):
- control devices operable without releasing the steering device
- control devices operable without releasing the steering device with the left hand
- control devices operable without releasing the steering device with the right hand
- control devices operable without releasing the steering device and the accelerator and braking mechanisms
Note: If the driver is using a push pull hand control and their upper limbs can move freely, an indicator pin switch will often be used to overcome the effect of the push pull hand control. In this case do not use code 35. The pin switch is only being used to overcome the effect of this design of hand control. This allows the customer to use more modern types of adaptations in the future.
40 – Modified steering:
- adapted steering wheel, for example, reduced in diameter or larger or thicker steering wheel section
- adapted position of the steering wheel
- foot operating steering
- one hand or arm operated alternative adapted steering system (e.g., steering ball or other type of steering device)
- two hand or arm operated alternative adapted steering system
Note: If the driver is using a push pull hand control and their upper limbs can move freely, a steering ball will often be used to overcome the effect of the push pull hand control. In this case do not use code 40. The steering ball is only being used to overcome the effect of this design of hand control. This allows the customer to use more modern types of adaptations in the future.
42 – Modified rear-view mirror(s) or devices:
- adapted mirror(s) or device for rear view
- additional inside device permitting side view
- blind spot viewing device
43 – Modified driver seat:
- driver seat height for normal view and in normal distance from the steering wheel and the pedals
- driver seat adapted to body shape or seat with lateral support for good stability
- driver seat with armrest
- seat belt with adaptation or with support for good sitting stability
8.08 Form D255 - completion - disability or failed eyesight test
A report form D255 must be completed in all cases, pass or fail, where a candidate has a disability, declared or undeclared, with adaptations fitted to their vehicle or fails the eyesight test.
In completing the form D255, the use of the boxes is self-evident. In addition, it will be necessary for examiners to observe the instructions below:
Note: In all cases the eyesight section of the D255 must be completed and not lined through. (With the exception of vocational tests)
Box 5
This is split into 4 sections as follows.
Do you consider that the candidate should drive vehicles with adaptations and/or automatic transmission to overcome the effects of the disability?
The examiner should briefly describe the adaptations fitted if the answer is yes. Where appropriate, describe the type of adaptation(s) considered necessary, e.g., “ball fixed to steering wheel, hand operated clutch”, etc.
Did the adaptations and/or automatic transmission overcome the effects of the disability?
The examiner should briefly give reasons if the answer is no.
Did the test show that the candidate would be unsafe as a driver of any kind of vehicle
Drivers Medical Branch (DMB) is seeking information here about whether the examiner considers the candidate would be unsafe to drive/ride vehicles of any kind. It is unlikely that someone who failed because adaptations to their vehicle were unsuitable or non-existent would warrant a ‘YES’ under this heading.
Note: Examiners should be aware that if they report the candidate would be unsafe as a driver of any kind of vehicle, DVLA will revoke (or refuse) a licence.
Do you have any other comments including likely effect of the disability on driving vehicles in other categories?
Particular attention should be given to the candidate’s ability to drive/ride vehicles in other categories. Comments should be made here to indicate whether the candidate’s disability would affect their ability to drive/ride other vehicles safely. The examiner should briefly describe the adaptations fitted.
Emailing form D255
The original copy D255 should be emailed on the day of the test to DVLA. Once the D255 has been successfully sent to DVLA, there is no need to retain a copy locally.
8.09 Restricted/abnormal stature
Extra-large or extra small stature is not of itself a disability and examiners should not normally restrict a pass certificate on those grounds, nor complete a D255. However, there may be cases where restricted or abnormal growth could be said to amount to a disability, in that it could have an effect on the candidate’s driving ability. If the controls of the candidate’s vehicle have been adapted in any way to overcome this disability, then the appropriate code should be entered on the DVSA10.
In such cases, a description of the candidate’s build, giving some indication of size, approximate height, and whether build appears to be in proportion, should be given on the Digital Test Report and a D255 should be completed.
8.10 Support for deaf candidates
The examiner should agree with the candidate and the person that has been delivering their training, how instructions about the route and manoeuvres are to be given. This could be done in writing or, if the candidate is accompanied by a signer, through them. The signer may be the ADI or accompanying driver. Examiners may use the Deaf Candidate Support Pack as part of making reasonable adjustments to help overcome a disability. The key is to help communicate with deaf candidates and to ensure the examiner’s directions and instructions are clear.
If the booking section knows that the candidate is profoundly deaf in both ears, 2 periods will be allocated for the test.
If a candidate reports for test with a hearing problem, which was not declared on their application, the examiner should ascertain the extent of the deafness and check whether it can be overcome by the radio equipment. If not, the test should be postponed so that it can be re-booked with more time. The procedure of rebooking should be explained to the pupil.
8.11 Without speech
Directions can be given without difficulty, although examiners should bear in mind the possibility that the candidate may not have understood them.
8.12 Combination of deafness and without speech
The examiner should conduct the test as far as they reasonably can, resorting to less conventional methods of communication if necessary. The test must not however be distorted to an unacceptable degree to meet the candidate’s needs. If the test cannot be conducted to a standard, which enables the examiner to reach a decision, they should terminate the test and make a report to the LDTM for onward transmission to the ODM.
8.13 Spectrum and processing disorders
For example, autism, Aspergers, sensory processing disorder (SPD).
These cognitive disorders can present themselves in a wide range of traits. The most common of these are difficulty with communication, anxiety, and sensory overload. Where a spectrum condition is declared or is apparent, and providing the test is not undermined, examiners should, wherever possible, adapt their approach to accommodate the candidate. An examiner may wish to consider communicating with the candidate in a quieter environment and giving them plenty of time to respond. Consider asking the candidate if they would prefer not to talk during the test as this could prove distracting and could even be interpreted by the candidate as being part of the test. The examiner should consider checking several times through the test that the candidate is keeping up with the information being given. When communicating, try to be clear and concise. Any specific information provided on the journal should be taken into account and wherever possible, reasonable adjustments should be made.
Many people on the spectrum that have SPD have heightened use of senses. This can create a sensory overload that may cause additional distractions and anxiety for the candidate. Therefore, consider avoiding routes where building or roadworks are taking place and routes that are known for low sun. If you see on the following day’s journal that you have a candidate on the spectrum or with an SPD, consider trying to avoid bright clothing and accessories and wear a more subtle fragrance.
A candidate with a declared spectrum condition may need very little adjustment, so it’s important for an examiner to assess every candidate on an individual basis and conduct the test in whichever way they best see fit.
8.14 Medical appraisals
Occasionally Drivers Medical Group (DMG) may require a disabled driver to take a driving appraisal even though they already hold, or have held, a full licence. This may be done when a driver has become disabled since the full licence was issued, or when a previously disclosed disability has become more acute. The test is to help medical advisers in assessing the driver’s licensing entitlement.
DVLA will email Medical Referrals with the candidate’s information.
ROS will contact an appropriate LDTM to request a time and date for the appraisal. LDTM will contact the candidate to arrange a mutually suitable appointment. The candidate should be given 3 weeks’ notice to allow them to prepare and seek development. However, the appointment needs to be made within a maximum 8-week target date, from initial notification to ROS.
You should allow a 1.5-hour slot to conduct the appraisal and complete the paperwork.
On completion of the appraisal, the bottom copy and the guidance notes should be given to the candidate. Retain the top copy for completion of the report write-up. Both sides of the report should be emailed to DVLA at eftd@dvla.gov.uk and to medical.referrals@dvsa.gov.uk with the result of the appraisal. Further guidance can be found in the DVLA Medical Appraisal SOP.
8.15 Interpreters
Candidates are not allowed to use foreign language interpreters on their test.
A special needs interpreter may accompany deaf and/ or deaf without speech candidates for tests conducted in English or Welsh only. The interpreter must be at least 16 years of age. In such cases a car should be used for the module 2 test.
An English or Welsh only speaking special needs interpreter is allowed on to the motorcycle manoeuvring area but must wear a reflective waistcoat. (Spare Hi viz waistcoats held at the test centre should be made available if required).
If a special needs interpreter turns up unannounced and a car is not available, then the test should be postponed.
8.16 Motorcycle specific
Licence Restriction Codes
Codes :
- 44 (1) Single operated brake
- 44 (2) Adjusted hand operated brake (front wheel)
- 44 (3) Adjusted foot operated brake (back wheel)
- 44 (4) Adjusted accelerator handle
- 44 (5) Adjusted manual transmission and manual clutch
- 44 (6) Adjusted rear-view mirror(s)
- 44 (7) Adjusted commands (direction indicators, braking light, etc.)
- 44 (8) Seat height allowing the rider, in sitting position, to have two feet on the road at the same time
- 44 (11) Adapted footrest
- 44 (12) Adapted hand grip
- 45 Motorcycle only with sidecar
- 46 Motor-tricycle
- 78 – Automatic transmission
- Use this code if the vehicle has no clutch pedal.
Important Note: Once the codes have been added to a licence, a driver/rider will no longer have entitlement to drive/ride vehicles/machines without these adaptations and they will be breaking the law if they do. In the future, if there is a change to the adaptations they need, they must inform DVLA. If an individual who passed their test with adaptations wishes to remove their adaptations, then they have to re-take their test.
8.17 Candidates with Special Needs
Examiners should take any special needs the candidate might have in to account and adopt a flexible approach to make reasonable adjustment to the way the test is conducted. This may include adapting the way a particular exercise is carried out or allowing a different vehicle to be used, including one with an e-clutch mechanism or other adaption.
Any questions related to this topic should be directed to technicalstandards@dvsa.gov.uk
8.18 Disabled riders and the motorcycle test
If direction indicators are fitted to a machine ridden by a candidate who cannot give arm signals, they must be regarded as a necessary adaptation to the machine.
Reasonable adjustments can be made to the motorcycle test. This will depend on the nature of a rider’s disability. Advice should be sought from Technical Standards for any unusual cases.
A disabled motorcyclist who cannot take direct rear observation, but otherwise meets the test requirements may be granted a pass certificate to ride a category A or AM machine; “with suitably positioned mirrors” (Restriction code 42).
A motorcyclist can be restricted to riding a combination machine if the examiner is not satisfied that they are capable of riding a solo machine safely. The appropriate category letter and disability code should be entered on the DVSA10, and the D255 should indicate that the candidate should be restricted to riding machines with sidecars.
8.19 Combination side cars & motor-tricycles
These vehicles used by candidates with a physical disability are not required to carry out the manual handling exercises or avoidance exercise; they are required to carry out the first circuit bend and the controlled stop in addition to the emergency stop exercise. Additional time should be allowed for this test to be conducted.
The decision on whether to use a left or right circuit should be based on the characteristics of the machine, generally if a sidecar is positioned on the left of the machine a right-handed circuit should be used and vice versa.
The examiner should remove cones number two and four from the slalom exercise to account for the increased turning circle of combination units, there should normally be no need to alter the two cones used for the figure of eight exercise. The width between the cones associated with the speed measuring device and the width of the controlled stopping box should be increased to 1 ½ times the width of the outfit.
The U turn may be carried out from either left to right or right to left side of the area, depending on the configuration of the combination unit some cones may need to be repositioned to take into account the increased turning circle of combination units only.
EU Codes:
- 45 motorcycle only with sidecar
- 125 motor-tricycle
8.19 Deaf candidates (motorcyclists)
In the case of deaf candidates or those with a hearing defect that would make radio communication impractical, the examiner should give directions on route with the aid of a diagram or map, taking into account the candidate’s local knowledge of the area. Care should be taken to ensure that the distance between briefing points is not too long, nor the directions too complicated.
8.20 LGV specific
LGV and PCV deaf and without speech candidates
In view of the recommendations about the medical fitness of LGV/ PCV drivers, it is very unlikely that an LGV/PCV test candidate would be deaf and/or deaf without speech. If such a candidate does attend for a test, the examiner should conduct the test and forward a note about the candidate’s condition to the LDTM for sending to the Driver and Vehicle Licensing Agency (DVLA), Swansea.
CPC (Module 4) - making reasonable adjustments
Due to the higher medical standard required for vocational licensing, it is unlikely you may encounter someone with a severe disability. You may find the candidate has some degree of restricted movement or declare special needs. There is no need to complete a D255, but it may be beneficial to make some discreet enquiries to ascertain how the candidate’s circumstances may affect their ability to complete the test in the same way as a non-disabled driver.
Careful observation of the candidate may show the need to make reasonable adjustments.
For example, it is not considered acceptable for a non-disabled person to enter or exit an LGV cab without applying the safety technique of “three points of contact.” However, a person with only one hand would clearly not be able to do this, but provided they make every effort to get in and out competently, this should be accepted. It is important, therefore, that the examiner or assessor exercises considered judgment in these exceptional circumstances and does not fail someone who can evidence ability to “do the job.”
9. Data Protection Act
9.01 Individual responsibilities
The implications of breaching the Data Protection Act are serious. Individuals are responsible personally for information they give out and are liable to be prosecuted if they are found to have disclosed information inappropriately. Legislation does not hold the agency responsible under these circumstances.
Contacting customers
Examiners must not use personal mobile phones or other personal devices to contact customers in connection with driving tests or any other DVSA business. Where communication with a customer is necessary, approved DVSA equipment and communication channels must be used, including office telephones or the authorised calling functionality available on DVSA-issued devices.
9.02 Customer service
DVSA have made great efforts over the last decade to allow examiners to conduct tests in a more customer-friendly manner and the Data Protection Act must not be used as an excuse to return to a less customer-focused approach. Information is still freely available through the correct channels to the correct people.
9.03 Test debrief - requests for information
At the start of the test, the examiners must ask the candidate whether they want their instructor/accompanying driver present on the test and for the result and feedback at the end of the test.
For digital tests, the candidate must confirm whether they want their end of test summary to be sent via email to the email address provided during booking, an alternative email address, or by post.
(If the test was not accompanied and the instructor/accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner should confirm with the candidate they want their instructor/accompanying driver present)
If the candidate elects not to have their instructor/accompanying driver present for the decision and de-brief, then the examiner should ensure that the candidate’s request is complied with.
Any subsequent enquiries made by the instructor about their pupil’s performance, must be referred back to the candidate in all cases. Examiners must not discuss previous tests with instructors.
9.04 Complaint
In the event of a complaint being received, examiners must not assume that instructors are aware of the candidate’s complaint - merely telling an instructor that a candidate has complained is a breach of the Data Protection Act. Examiners must not bring to the attention of, or discuss with instructors, customer complaints.
9.05 Requests for information over the telephone
No information regarding driving test performance may be discussed (with a third party). All requests should be referred to the HEO, SEO, or Customer Service Centre to answer.
9.06 Written requests for information
If a candidate writes requesting information about their particular test, DVSA must supply that information. Forward all written requests to the HEO, SEO, and area customer service unit to answer.
9.07 Information security incidents
An information security incident is any actual or potential compromise of DVSA’s information.
An information security incident is any actual or potential compromise of DVSA’s data, systems, or activities.
Examples are varied and include:
- physical security of DVSA sites, for example faulty CCTV or broken windows
- unauthorised disclosure of personal or sensitive information, for example being sent to the wrong recipient
- lost or stolen information or equipment
- information kept longer than necessary
- breaches of information management and security policies or legislation, such as the Data Protection Act
Reporting procedure
You must report security incidents to the Information Management, Security and Data (IMS and D) team immediately.
You can do this by completing the reporting form and emailing it to information.handling@dvsa.gov.uk.
You must report security incidents immediately.
Investigation
The IMS and D team will then:
S1. See whether a genuine incident has occurred.
S2. Analyse the incident to understand what has happened and why.
S3. Contain the incident.
S4. Identify improvements that can be put in place to reduce the risk of it happening again.
9.08 General
The DVSA does not charge for supplying written information. Test results are emailed directly to candidates after the test, using the email address provided in their booking record.
If a candidate requests to see all information held about them within the agency, they should contact dataprotection@dvsa.gov.uk. If a third party writes on the candidate’s behalf, the DVSA cannot process the enquiry or complaint without the candidate’s written permission.
10. Incident and legal procedures, and other non-operational matters
10.01 Incident on test involving candidate’s vehicle
If the candidate’s vehicle is involved in a collision or incident and the candidate shows no sign of stopping to comply with legal obligations, the examiner should inform them that they are required by law to do so and, if necessary, give advice about exchanging names and addresses. Bumper and mirror touches should be judged on merit. In most cases, provided there is no damage, these should not be treated as a collision or incident.
If the candidate’s vehicle is rendered un-roadworthy, or compliance with legal obligations leaves insufficient time to complete the test, then the test should be terminated.
The test should also be terminated if the candidate indicates that they do not wish to continue or if the examiner considers it would be unwise to continue because the candidate appears to be suffering from shock or other adverse reaction or is unduly nervous.
If the test is terminated, and the collision or incident was clearly and totally the fault of the candidate, a result end of test summary should be issued. If the collision or incident was clearly not the candidate’s fault, then the test should be terminated without any result.
10.02 Incident reporting procedure in DVSA
As per the Incident Reporting Policy, all incidents of any kind involving injury or damage must be reported to the Health and Safety team using the HS1 Incident report form.
Managers are accountable for ensuring that arrangements exist for recording all collisions and incidents where injury or damage has occurred within their areas of responsibility.
Examiners are reminded that the H&S incident report form might be used by the agency’s legal advisers in anticipation of legal proceedings against the agency or officials, and professional privilege may be claimed for it in appropriate cases. It should not be shown to the police or to any other person outside the agency. The Operational Delivery Manager should be notified immediately of any request for it.
10.03 Insurance details
The driver of a vehicle involved in a collision or incident which causes damage or injury to any other person, vehicle, animal, or roadside property is required by law to stop, give their name and address and owner’s name and address, and vehicle registration details, and produce a certificate of insurance to any person who has reasonable grounds for requiring its production, or report the collision or incident to the police as soon as reasonably practicable, and in any case within 24 hours and produce a certificate of insurance.
If an examiner is injured in a collision or incident on test, they are advised to exercise their rights under these provisions and obtain the necessary insurance details at the time of the incident or as soon as possible thereafter, either from the parties concerned or from the police.
10.04 Circumstances not covered by these instructions
Separate instructions follow for England and Wales and for Scotland. If circumstances arise which do not appear to be covered by these instructions, they should be considered in the first instance by the HEO and the SEO. If it appears to them that further advice is needed, this should be obtained from Technical Standards.
10.05 Instructions - England and Wales
The following instructions are based on the principles that:
- all reasonable assistance must be given to the police and judicial authorities
- examiners must remain impartial and avoid giving reason to be identified with the police or other parties
- a clear distinction is drawn between statements given to the police or other parties and reports which an examiner makes to the agency. Reports to the agency are made in confidence and are not for publication
- statements are confined to observed facts. A statement should not contain deductions or other expressions of opinion. Examiners must not prejudge or appear to prejudge matters, which are for a court to decide
Action to be taken by an eye witness of an incident
Examiners have the same duties and obligations as any other person going about their daily business. If they witness a collision or incident during the course of their duties they should:
- if the candidate’s vehicle is involved, make themselves known to any other persons involved in the collision or incident
- if the candidate’s vehicle is not involved, exercise discretion in deciding whether or not to stop and make themselves known to the parties involved. They should take account of the circumstances at the time and bear in mind such considerations as their responsibility towards the candidate, the presence of other witnesses, and the seriousness of the collision or incident
Request for oral statement or interview
If an examiner is asked by the police to make an oral statement they should offer to submit a written statement instead. If the police persist in their request the examiner should comply, confining the statement to facts of what they actually saw.
In the case of a fatality, any request for an oral statement from the coroner or his representative should be met in the same way.
Request for written statement
Requests from the police or from, or on behalf of, any party involved in the collision or incident should be met.
Legal proceedings
If legal action arises from an collision or incident, the agency must act impartially. Written information or statements must be sent to all parties to a dispute. An examiner’s statement should be confined to matters of observed fact on which they are in a position to give evidence in court. It should exclude expressions of opinion and avoid the expression of any agency view or policy.
The statement should normally be submitted to the HEO, together with the request for it and the official incident report. The HEO will check the statement and forward the papers to the SEO.
Where an oral statement has been given to the police, and a subsequent request for a written copy of that statement is received from any party to legal proceedings, the SEO should pass the request to the police and request copies of the statement so that one can be sent to the enquirer and one retained on the agency’s file.
Interviews
Requests for an oral statement or an interview from any party to legal proceedings should be refused.
If, however, the other party continues to request an interview, the facts should be reported immediately to the SEO so that advice can be obtained from Technical Standards.
Attendance at court
Except when appearing in a case to which the Secretary of State, the agency, or the traffic commissioners is a party, or in a case brought by police or the director of public prosecutions, an examiner should attend court only when served with a witness summons or a subpoena.
Attendance in response to a witness summons or subpoena is compulsory
Receipt of a subpoena should immediately be reported to Technical Standards via the SEO.
Summons or subpoena to appear
Evidence given by an examiner in court should be confined to the facts. Witnesses are entitled to refresh their memory by reference to notes made by them at the time of the collision or incident. They should not refer to official reports or documents.
If pressed to express an opinion as to the cause of a collision or incident, an examiner cannot refuse to do so, but must make clear that it is their personal view arising out of the observed facts.
Summons to produce documents
If an examiner is asked to produce a report or official document not available to the public, a note of the circumstance of the case together with the documents in question should be sent to the SEO who will seek advice from the treasury solicitor as to whether the documents may be released.
An official report or any document not available to the general public should not be taken to court by an examiner unless advice has been obtained from the SEO.
Expenses
Examiners who are called upon to attend court to give evidence in their official capacity are regarded as being on official duty. Travelling and subsistence expenses should be claimed from the agency under the normal rules.
Recovery of expenses from the court should be dealt with as follows:
- for attendance at court in connection with criminal proceedings, no claim should be made for recovery of expenses
- examiners summoned in connection with a private lawsuit should claim witness’s expenses from the solicitors who issued the summons. They should be asked beforehand for an undertaking that the proper expenses will be paid whatever the outcome of the proceedings. However, if such an undertaking is not given, the examiner must nevertheless attend court and claim the witness expenses later
Witness expenses should be based on the examiner’s gross salary and calculated as follows:
- gross monthly salary, (plus London weighting if applicable) divided by
- number of days in the month in question, multiplied by
- number of days in court plus travelling and subsistence expenses
The expenses should be scaled down appropriately for absences of less than a day. The amount of expenses that may be paid in county court cases is restricted by the county court rules. It is therefore important that the persons calling the examiner as a witness are informed of the amount that they will claim.
To avoid difficulties over the payment of claims an undertaking should, if possible, be obtained from the solicitors issuing the citation that the witness’s attendance fee and subsistence and travelling expenses will be paid. Any sums recovered should be remitted to the area office.
10.06 Instructions – Scotland
An examiner in Scotland is an ordinary citizen with a citizen’s rights and duties even when they are on official duty. They must be impartial and avoid giving reason to be identified with the police. The procedures in Scotland follow broadly those for England and Wales but there are differences in law and practice to be remembered.
Providing information
Examiners who have witnessed a collision or incident should provide their name and address to anyone involved or any person, such as the police, who reasonably requires it.
Statements
If asked to provide a statement of what they observed, examiners should offer a written statement of facts, provided the requester has reasonable grounds. This includes people involved in the collision or incident, solicitors, police officers, or a member of the Procurator-Fiscal’s department. If an interview (precognition) is requested instead of, or after, a written statement, examiners must comply. A copy of any written statement should be sent to the LDTM and, in civil cases, to other parties involved if requested.
Court attendance and expenses
Expenses for court attendance:
- official duty: Attendance at court is considered official duty. No claims for travel or subsistence expenses should be made on the court; these should be claimed from the agency under normal rules.
- civil action witness fees: If examiners are cited to appear in a civil action, they should negotiate a witness fee with the litigant or their solicitor, subject to the decision of the auditor of court in case of a dispute.
Calculating witness fees
S1. Gross monthly salary: Divide by the number of days in the month in question. S2. Multiply: By the number of days in court. S3. Add: Travelling and subsistence expenses.
Claims should be scaled down for absences of less than a day. Note that amounts payable are limited by court regulations. To avoid payment difficulties, obtain an undertaking from solicitors issuing the citation that the witness’s attendance fee, and expenses will be paid. Remit any sums recovered to the area office.
10.07 Reporting injuries
If an examiner sustains an injury, however slight, during working hours, a report must be immediately submitted using the HS1 incident report form.
10.08 Reporting assaults
All cases of physical assault, serious threats, and ‘drive away’ incidents with the examiner present against their consent must be reported immediately to the police and the LDTM.
Examiners must notify Customer Support on the examiner telephone line straight away following any type of assault or threat by a candidate, and a booking review marker (BRM) will be added to TARS to prevent the candidate from booking online.
A full written report of the incident should be completed on form HS1, providing as much details as possible (police ref numbers, number plate numbers, driving licence details of parties involved) and transmitted to the Health and Safety team via Microsoft forms. Additional information or photographs can be sent to reportanincident@dvsa.gov.uk.
If the assaulted examiner cannot make a report, the most senior examiner on duty should complete and send it.
All assaults must also be reported on form HS1 in the same way. The HS1 report must be submitted as soon as possible and within 24 hours if police have been notified.
10.09 Police involvement and legal action
If the police decide to prosecute, they should be assisted with statements or evidence. If the police do not prosecute, and the assault occurred due to the examiner performing official duties, DVSA will seek legal advice and pursue cases where advised there is a reasonable chance of conviction. Cases are considered based on evidence and seriousness. Examiners may seek support from TUS or institute legal proceedings through their solicitor. In Scotland, corroborative evidence is necessary. Prosecutions are by the Lord Advocate, carried out by the Procurator Fiscal service. Private prosecutions are rare, and the examiner cannot initiate court action themselves.
10.10 Third-party insurance
The Road Traffic Act mandates insurance for motor vehicle users against liability for death or personal injury to third parties, including passengers. An examiner is like any member of the public if injured due to driver negligence. An examiner, or their dependents if killed, can claim damages against the negligent driver. If negligence is not admitted, a civil action can be brought. Insurers usually pay agreed or awarded damages. If no valid insurance exists, the motor insurers’ bureau may cover damages and costs under certain conditions, including prior notice of intent to sue the uninsured driver.
If an examiner is injured due to negligence by both the driver of their vehicle and another driver, a claim can be filed against both. According to the staff handbook, damages awarded against a negligent driver may affect an injury benefit under the principal civil service pension scheme. An examiner pursuing a claim should comply with staff handbook provisions.
10.11 Private insurance
Examiners may arrange private insurance against injury or death during a driving test. Terms are between the examiner and the insurer. Payments under private insurance do not affect civil damages claims or civil service benefits.
10.12 Civil legal proceedings
If injured by a wrongful act, staff can pursue civil legal proceedings. The agency may provide financial assistance. Applications for assistance go through the SEO.
For examiners injured during official duties:
- notification: Inform the LDTM if legal proceedings are planned
- consultation: With prior approved application, the agency pays for consulting a solicitor to assess claim viability. Send the account and solicitor’s opinion through the SEO to HR Business Partner
- contributory negligence: Report defence claims of contributory negligence to SEO immediately. The agency will consider involvement extent
10.13 Police requirements
Police can require a person supervising a provisional licence holder to produce a licence and provide their and the vehicle owner’s details. An examiner, not responsible for supervision, should:
- explain they are a DVSA driving examiner conducting a driving test
- produce their identity card, and licence if available
- Ii no licence is available, offer to produce it within seven days at a nominated police station
10.14 Legal proceedings against staff
Examiners must report to their HEO on receiving a notification to appear in court for a criminal charge, providing offence details and hearing date and venue. An agency representative will attend. If involved in an incident related to their driving, on or off duty, which might lead to prosecution, or if receiving a notice of intended prosecution, complaint, or fixed penalty offer, inform HEO immediately, providing incident details and any relevant information. Send a copy of the report to SEO for Grade 7 and Grade 6. Notify HEO and SEO immediately of all subsequent actions, such as:
- receipt of court proceedings notice or adjournment
- developments, such as pleading guilty by post, with a copy of the letter to the court
- case results
Failure to comply with these instructions may result in disciplinary action. All motoring offence convictions are subject to disciplinary review, potentially leading to termination. Automatic termination occurs if convicted of offences resulting in disqualification or involving drink or drugs, regardless of disqualification.
10.15 Publications and media statements
Examiners, like other civil servants, must treat any letter or document received in an official capacity as an official document. It breaches the Official Secrets Act to disclose it to unauthorised persons. This applies to letters received directly at test centres or passed to examiners. The agency decides on legal advice for personal or objectionable content. Information about candidates or instructors gained through official duties is confidential and cannot be disclosed without authority.
An examiner wishing to disclose official information or use official experience in outside activities must first obtain written HR permission through the SEO. Examiners must not publish material, deliver speeches, or write books without prior permission. Obtaining permission before negotiations with private publishers avoids copyright issues.
Examiners should not write to the press about official duties or participate in media broadcasts without prior authority from:
Engagement and Communications
DVSA
1 Unity Square Queensbridge Road Nottingham NG2 1AY
Failure to obtain prior authority or permission is a disciplinary offence.
10.16 Publicity about driving tests
If the press or media gives misleading publicity about a driving test, an examiner aware of this, and identifiable from it, should send a report with the facts to their HEO and SEO. For press comments, include the press cutting with the publication’s name and date. This should be done promptly. Obtain related documents through the HEO and forward them with the report to refresh memory if needed.
Driving test centres may receive interview requests from the press or other bodies. Examiners are not authorised to grant these requests and should not commit the agency. Avoid appearing uncooperative by referring the caller to the DVSA press office at pressoffice@dvsa.gov.uk and notify the HEO.
10.17 Outside activities
Examiners have a particular responsibility to be constantly vigilant and alert to potential criticism at all times. Because some activities can place them very much in the public eye, they are required to obtain prior approval before taking up any outside activity, paid or unpaid. Written applications should be made through the line management chain to the SEO.
Examiners who wish to take up part-time employment will be required to comply with the conditions laid down in the DVSA guidance on the working time directive and secondary employment. Examiners who wish to perform special constable duties may do so subject to obtaining prior approval from the SEO.
10.18 Examiner becoming an ADI
When an approved driving instructor (ADI), who is currently on the register is employed as a driving examiner, from day one of their examiner training they must stop giving driving instruction and their ADI badge must be surrendered to their trainer. If they leave the agency they can apply to have their ADI badge returned as long as it has not expired, or an application is made to the Registrar within 12 months of the date of expiry. If they leave DVSA after this date their ADI badge cannot be returned.
An examiner who is retiring from or leaving the DVSA and intends to become an ADI and is currently conducting both ADI qualifying exams and ADI Standards Checks may apply for an ADI badge before they leave. They must not, however, give instruction on a professional basis until they have left the agency.
Note: This is subject to paying the registration fee, Disclosure & Barring Service (previously CRB) checks and making themselves available for standards checks following inclusion onto the ADI register.
If an examiner does not qualify to have their ADI badge returned or currently does not conduct the full range of ADI duties but intends to become an ADI after leaving the DVSA, he/she must pass the ADI qualifying examinations to gain access to the register. This will be at their expense.
Once a leaving date has been established, it is possible for staff to start the ADI application process before they leave the DVSA. Any driving examiner grade may apply to take the ADI qualification examinations during the last six months of their service. They must not, however, give instruction on a professional basis until they have left the DVSA. Applications to take the examinations under these arrangements should be made in writing through the Line Manager to the ADI Registrar.
As with all ADI applications the Registrar retains discretion on anyone being accepted onto the register of approved driving instructors.
10.19 Health and safety at work
A health, safety, and working environment manual containing advice and generic risk assessments that apply to the agency, prepared in consultation with the trade union side (TUS), is available in every permanent centre. The manual must be kept where it is readily accessible to all DVSA staff.
10.20 Protective clothing
Examiners are provided with suitable protective clothing according to the circumstances under which they have to work. Enquiries relating to protective clothing (for repair and ordering) should be made through the examiner’s line manager.
10.21 Appointment fees
Examiners should know the current fee for a test appointment but should not otherwise concern themselves with questions relating to fees. It is the responsibility of the booking section to ensure that candidates have paid for their appointments, and to advise on and implement the rules relating to the forfeiture of fees. Candidates, or others, who make enquiries relating to fees should be referred to the national booking number.
10.22 Institute of advanced motorists
The council of the Institute of Advanced Motorists has agreed that the agency’s examiners are eligible for membership of the IAM without having to take the institute’s driving test. Examiners wishing to take advantage of this facility may obtain application forms from the LDTM or, in the case of examiners successfully completing the new entrant training course, the training establishment. The appropriate fee to cover the first year’s membership must accompany applications.
11. Guide to assessment and marking
11.01 Introduction
This section outlines the requirements of a driving test, providing a brief explanation of the skills and abilities the candidate is expected to demonstrate in each aspect of their driving. It also includes examples of the assessment criteria, which serve as a guide to assessment.
The purpose of the guide is to explain the assessment criteria and recording of faults under the outcome/competency headings on the driving test report. Although an attempt has been made to explain assessment in theory, it should be remembered assessment is a knowledge and practical-based skill.
Examiners are trained to assess driving tests to a uniform standard; the Chief Driving Examiner sets these standards. Examiners should apply the assessment principles in which they have been trained. The training of this skill is delivered to a high standard by experienced examiner/trainers.
Assessment is maintained through infield development and supervision supporting DVSA’s quality assurance regime. Applying a robust quality assurance system preserves the quality of assessment skills of all driving examiners in conducting a professional, consistent, and uniform driving test.
An assessment of the ability to drive safely is made by taking direct observation of the candidate’s driving, assessed against a set of outcomes/competencies found in the DT1 and the respective DVSA National Driving Standards . As such, assessing a person’s competence to drive is based on the making of safety decisions and vehicle control.
This guide cannot include all of the situations that may be encountered during a driving test. However, the following examples provide an insight into the assessment and marking process.
11.02 Identification and recording of faults
It is important that, in addition to a common standard of test, there should be a common standard of assessment of candidates’ driving ability. The most reliable basis for assessing a person’s competence to drive is to observe faults as they are committed and to evaluate them as soon as a confident judgement can be made.
Examiners should not be too hasty in making a definitive assessment and marking the fault. Examiners should wait until the event has finished, then mark the fault. Driving errors must not be double-marked. Once assessed, each fault should be recorded on the Digital Test Report in accordance with the definitions laid out below.
Note: When assessing and marking a manoeuvre, it is not considered as double marking to mark both control and observation.
Fails as a result of either one serious fault or one dangerous fault and an accumulation of 16 or more driving faults - the written report only needs to cover the serious or dangerous fault. Fails as a result of an accumulation of 16 or more driving faults only need to be written up in full.
11.03 Fault assessment – defined outcomes
Before any fault identification and analysis can be carried out, the outcome must first be defined. Any deviation from the defined outcome can then be seen as a fault. The weight or severity of the fault will depend on the extent of the deviation, and the circumstances at that time. The fault can range from ‘not worthy of recording’ to ‘dangerous’.
The following is an example of a Defined Outcome:
At every junction or hazard the candidate should adopt a structured planned approach, such as the MSM/PSL Routine:
Mirrors Signal Manoeuvre (MSM):
- M: check mirrors to assess the speed and position of vehicles behind
- S: signal clearly and in good time
- M: manoeuvre using the PSL routine
Position Speed Look (PSL):
- P: position the vehicle correctly and in good time
- S: adjust speed as necessary
- L: look for other traffic, assess the situation, and act accordingly
11.04 Definition of faults
Faults are defined as follows.
Not worthy
Any insignificant deviation from the defined outcome that does not compromise safety or can be a matter of finesse.
Driving fault
A driving fault is one that falls short of or deviates from the defined outcome of the standard of driving of a safe and competent driver.
In isolation a driving fault does not result in failure to pass the test. However a candidate who habitually commits a driving fault in one aspect of driving throughout the test, cannot be regarded as competent to pass the test. The repeated fault can then be assessed as potentially dangerous.
Serious fault
A serious fault is one that is potentially dangerous or entails a breach of the law.
Dangerous fault
A dangerous fault is one involving actual danger to the examiner, candidate, the general public, or property. (Note: If the fault has been assessed as dangerous then this should be marked regardless of any action taken by the examiner).
11.05 Low and high risk
Fault identified - not worthy (not worthy of recording).
Any insignificant deviation from the defined outcome that does not compromise safety or can be a matter of finesse. For example - Dry steering, sequential gear changes, not pressing the button on top of the handbrake when applying it.
Low risk - driving fault (not an immediate fail)
Any sufficient deviation from the defined outcome that does not compromise safety, or can be a matter of control - to justify a fault being recorded. For example - the candidate took observation before emerging at the junction. However, they misjudged the distance of an approaching vehicle, causing it to slow down, safety was not compromised. (Sixteen or more of these faults would result in failure of the test.) There can however be occasions when one specific driving fault could by constant repetition, be regarded as serious and therefore a significant risk; for example when a candidate habitually fails to take mirror observation when appropriate.
High risk - serious fault (entails immediate failure)
Significant deviation from the defined outcome with safety, control and/or legal requirement breached. For example - the candidate did not take effective observation before emerging at the junction, unaware of any other road user who may have been expected to be there.
Actual danger - dangerous fault (entails immediate fail)
Safety, control and/or legal requirement breached that would have caused actual danger. For example - the candidate did not take effective observation before emerging at the junction completely misjudged both speed and distance of an approaching vehicle. The examiner had to take action to avoid a collision.
Examiners, may have to take ‘action’ when it becomes necessary to do so in the interest of public safety, including their own and that of the candidate. Such intervention may be either - VERBAL (ETA-V) or PHYSICAL (ETA-P).
The distinction between a verbal ETA and advice can be determined by the level of intervention required during the driving test. Advice is given when a fault is observed and there is no immediate danger. This allows the examiner to advise the candidate without the need for urgent action. In contrast a verbal ETA is used when an immediate intervention is necessary to prevent a situation from potentially escalating into a dangerous one. The verbal ETA box should be marked when the examiner’s intervention directly prevents a fault from becoming hazardous or serious.
11.06 First rule of assessment
The first rule of assessment in the driving test serves a guiding principle for examiners when determining whether a candidates performance should result in a fail. It asks the examiner to evaluate a fault by considering the following question: ‘’If the drive was perfect before and perfect after this fault occurred, would this fault and this fault alone, cause the candidate to fail their test?’’
This rule ensures that the examiner focuses on the severity and impact of the individual fault rather than allowing it to be overshadowed by other factors in their drive. The fault must be assessed in isolation, taking into account whether it represents a significant breach of safety, legal compliance, or control that could endanger the candidate, other road users or property. If the fault is serious enough to undermine overall road safety or legal adherence, it would be sufficient grounds for failure.
11.07 Breach of legal requirement
A breach of legal requirement during the driving test refers to an instance where the candidate violates the law or regulation governing the road use. Such breaches include not responding to a red traffic light, driving well above speed limit or not responding to a stop sign.
A breach of this nature would be considered a serious fault and would therefore lead to failure to pass the test. The purpose of the driving test is to assess whether a candidate is capable of driving safely and responsibly within the legal framework.
11.08 16th driving fault
The 16th fault rule of assessment is a hypothetical threshold used to help examiners determine whether a driving fault should be recorded. Although a candidate is permitted to accumulate up to 15 driving faults before failing, this rule applied to every fault, regardless of whether if it is the first or the last committed fault. The examiner must assess each fault individually by asking the question: If this was the 16th fault, could you justify it resulting in the candidate failing their test?
The purpose of this rule is to help the examiner decide whether a fault is sufficient enough to be recorded as a driving fault, or whether it can be deemed as a not-worthy fault.
11.09 Adding and taking away
The adding and taking away is more a tool than a rule of assessment, it should be used by examiners to evaluate severity of a fault committed by the candidate. It encourages examiners to consider the weight of the fault by asking themselves: ‘”Could you add anything to that fault to make it worse? Or could you take away anything to make it better?”
This tool aids in determining the seriousness of the fault and whether it should be recorded. For example, if a candidate brushes the kerb when pulling up on the left, the examiner should ask, ‘’Could this fault be worse? In this case, yes – it could be worse if the candidate has bumped into or mounted the kerb, which could indicate sufficient of significant lack of control. The examiner should then consider, ’’Could something be taken away? Yes, if the candidate has positioned the vehicle slightly further from the kerb, it could have been considered a perfect manoeuvre.
By using this tool, examiners are able to assess each fault in a broader context. If a fault could realistically have been worse, it may indicate a sufficient lapse rather than a serious issue. Conversely, if improving the situation requires only a small adjustment, it may not warrant recording a fault at all.
11.10 Extended test (assessment of faults)
The normal methods of assessment should be applied. However, examiners are reminded that most candidates are likely to have had considerable driving experience prior to their mandatory disqualification. Because of this, their method and standard of driving will probably be quite different to that of the majority of learner drivers. For example, their ability to take advantage of gaps in the traffic to emerge safely from junctions is likely to be to a much higher standard than that of the less experienced driver. They should not be penalised for this.
11.11 Assessment of each competency
Eyesight
Expected outcome / competence
Read, in good daylight, (with the aid of glasses or contact lenses if worn) a registration mark containing letters and figures 79mm high and 50mm wide, fixed to a motor vehicle at a distance of 20 metres. 12.3 metres for category K.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Not applicable |
| Serious fault | Unable to meet the requirements of the eyesight test |
| Dangerous fault | Not applicable |
Vehicle safety check questions – cars
Show me / tell me
One or both questions answered incorrectly will result in one driving fault being recorded. However, examiners should not unduly pursue questions to elicit precise responses. These are basic safety checks, and in-depth knowledge is not required for answers to be acceptable.
If the candidate commits a serious or dangerous fault while demonstrating the ‘show me’ question on the move, this will be recorded as a serious or dangerous fault at ‘Vehicle checks’. If, during the ‘tell me’ question, the candidate attempts to turn the ignition, the Examiner should intervene and explain that this is unnecessary as a demonstration is not required. If the candidate continues and inadvertently starts the car in gear, and the Examiner must take action, an ETA would be recorded, and a serious fault recorded as ‘Precautions’. The candidate may complete the check correctly, so nothing would be recorded under ‘Safety questions’ or ‘Tell me’ question.
If the candidate cannot identify controls during the ‘show me’ question, the examiner should ask them to pull up at the first suitable opportunity. The candidate will then be given a chance to identify the controls while stationary. If they correctly locate the controls, the same question should be revisited while driving and assessed accordingly.
If the candidate is still unable to locate the controls while stationary, the examiner should offer advice on operating them and then repeat the question while driving. This is likely to be assessed as a driving fault, provided there was no loss of control during the demonstration while driving.
As vehicle technology advances, more cars are equipped with electronic diagnostic systems that inform the driver of the state of the engine fluid levels, tyre pressures, etc. It is acceptable for a candidate to refer to the vehicle information system (if fitted) when answering questions on topics such as fluid levels or tyre pressures.
Examiners need to be aware that, although it may be necessary to carry out some of the checks, the ability to open the bonnet is not one of the competencies required. Instructors are expected to teach it, but should a candidate experience difficulty, it will be acceptable for the accompanying driver to assist in opening
Highway Code / safety questions (tractor, specialist vehicles and vocational tests only)
Expected outcome / competence
Candidates who have not taken a separate theory test, for example, to obtain a licence for a tractor or other specialist vehicle, will be asked questions on the Highway Code and other related motoring matters. Candidates taking a Passenger Carrying Vehicle (PCV) test should know the location of, and be able to operate, safety components such as a fire extinguisher, fuel cut-off switch, and emergency door.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Of the 5 questions asked / 6 traffic signs shown, a proportion are incorrect |
| Serious fault | All questions and traffic signs are incorrect |
| Dangerous fault | Not a moving exercise, therefore not possible to satisfy this criteria |
Vehicle checks
Show me / Tell me
Expected outcome / competence
Display and demonstrate a basic knowledge and use of the fundamental controls and safety checks applicable to the vehicle. For example, safe fluid levels, lighting and tyre checks, and washing the windscreen
Assessment criteria (examples)
| Type of fault | Example |
|---|---|
| Driving fault | Category A and domestic categories: One driving fault for one or both questions answered incorrectly. Category B: Answering one ‘tell me’ question incorrectly and/or displaying a minor loss of vehicle control whilst demonstrating the on-road ‘show me’ question. Category C, D, and ADI: One driving fault for each question answered incorrectly. Category C+E and D+E: One driving fault for each question answered incorrectly. |
| Serious fault | Category A and domestic categories: not applicable. Category B: Displaying a serious loss of control whilst demonstrating the on-road ‘show me’ question. Category C, D, and ADI: All five questions answered incorrectly. Category C+E and D+E: Both questions answered incorrectly. |
| Dangerous fault | Category B: Displaying an actual dangerous loss of vehicle control whilst demonstrating the on-road ‘show me’ question requiring examiner action to prevent a collision. Not applicable to all categories other than category B. |
Reverse right
Control / observation
Expected outcome / competence
Demonstrate the ability to safely pull up on the right-hand side of the road and reverse 2 car lengths. Effective all-round observation throughout the manoeuvre is required, showing consideration to other road users.
Assessment criteria (example: observation)
| Type of fault | Example |
|---|---|
| Driving fault | A misjudgement of the speed and distance of an approaching vehicle when beginning to move over to the right-hand side of the road. The safety of other road users was not compromised. |
| Serious fault | A misjudgement of the speed and distance of an approaching vehicle, causing the driver to brake heavily to allow the candidate to proceed to the right-hand side of the road. |
| Dangerous fault | Any situation brought about by the above loss of control that resulted in actual danger to the examiner, candidate, the general public or property. |
Reverse park road / car park
Control / observation
Expected outcome / competence
Ability to control the vehicle accurately when parking on the road or into a parking bay. Effective all-round observation throughout the manoeuvre showing consideration to other road users.
Assessment criteria (example: control)
| Type of fault | Example |
|---|---|
| Driving fault | Re-positioning is required to correct a loss of control or accuracy. |
| Serious fault | Excessive re-positioning to correct a complete misjudgement and/or significant loss of control. Final parking position parking - outside the bay. |
| Dangerous fault | Any situation brought about by the above loss of control that resulted in actual danger to the examiner, candidate, the general public or property. |
Forward park
Control / observation
Expected outcome / competence
Ability to control the vehicle accurately when forward parking into a parking bay. Effective all-round observation and consideration to other road users and pedestrians.
Assessment criteria (example: control)
| Type of fault | Example |
|---|---|
| Driving fault | Finishing the exercise with one or two wheels on the parking bay line. |
| Serious fault | Finishing the exercise with one or two wheels fully in the bay adjacent to the intended bay. Demonstrating a unacceptably poor standard of control over speed and / or direction. |
| Dangerous fault | Loss of control resulting in the examiner taking action to prevent the candidate from hitting a vehicle in the adjacent bay. |
Reverse (vocational / tractor and specialist vehicle tests)
Control / observation
Expected outcome / competence
Ability to control the vehicle accurately whilst reversing to the left. Effective all-round observation throughout the manoeuvre showing consideration to other road users.
Assessment criteria (example: observation)
| Type of fault | Example |
|---|---|
| Driving fault (tractor and specialist vehicle tests only, not vocational tests) | Demonstrates understanding of rear observations, but is late when taking the required observation. |
| Serious fault | Essential observation missed when starting the manoeuvre, did not react to the presence of other road users. |
| Dangerous fault | Any situation brought about by the above lack of observation that resulted in actual danger to the examiner, candidate, the general public or property. |
Uncoupling / re-coupling (vocational +E tests only)
Expected outcome / competence
Demonstrate the skills necessary when uncoupling and recoupling the vehicle. Drive the towing vehicle to a designated position prior to recoupling safely.
Assessment criteria (example: Uncoupling/recouple)
| Type of fault | Example |
|---|---|
| Driving fault | When uncoupling, the landing gear handle was not stored and secured. |
| Serious fault | When recoupling, the landing gear handle was not stored and secured, resulting in a potential risk to other road users when the vehicle is mobile. |
| Dangerous fault | Any fault that results in serious damage to the vehicle, candidate or third party. |
Controlled stop
Promptness / control
Expected outcome / competence
Display a high level of skill in bringing the vehicle to a stop, safely, promptly and under full control avoiding locking the wheels. Remember, in wet weather it can take twice as long to stop safely.
Assessment criteria (example: control)
| Type of fault | Example |
|---|---|
| Driving fault | Locking the wheels, resulting in skidding for a short distance, but demonstrating effective skills in regaining control. |
| Serious fault | Very harsh braking, resulting in locking the wheels. Vehicle continues to skid out of control, with either ineffective or no attempt to regain control. |
| Dangerous fault | Any situation brought about by the above loss of control that resulted in actual danger to the examiner, candidate, the general public or property. |
Control
Including:
- accelerator
- clutch
- gears
- footbrake
- parking brake
- MC front brake
- steering balance MC
- LGV
- PCV
- PCV door exercise
Expected outcome / competence
This section covers, where appropriate, the safe and controlled use of accelerator, clutch, gears, footbrake, parking brake, and steering. Additional specific control elements apply to the drivers of different vehicle categories. The vehicle’s controls should be used as smoothly as possible, e.g.
Making proper use of:
- accelerator and clutch to make a smooth start - the clutch should be depressed before the vehicle stops
- the correct gear should be selected to match the road and traffic conditions
- the vehicle should not be allowed to coast by running on in neutral or with the clutch depressed
- the footbrake should be used smoothly and progressively
- full use of the parking brake should be used, to prevent the vehicle from rolling backwards or forwards
- the vehicle should be steered as smoothly as possible. Steering too early/late may cause the vehicle to hit the kerb or swing out towards another road user. When a motorcycle is being ridden slowly, a straight line should be maintained. The machine should not wobble towards other vehicles
Assessment criteria (example: gears)
| Type of fault | Example |
|---|---|
| Driving fault | Incorrect gear selection, resulting in a reduction in vehicle speed with no risk to following vehicles. |
| Serious fault | Incorrect gear selection, resulting in a sudden reduction in vehicle speed, causing following traffic to alter speed/or direction. |
| Dangerous fault | Any situation brought about by the above control faults that resulted in actual danger to the examiner, candidate, the general public or property. |
Precautions
Expected outcome / competence
Before the engine is started, the candidate should make sure that they are comfortably seated and all controls can be safely operated.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | After stalling at a road junction, handbrake applied but attempts to start the engine whilst in gear. |
| Serious fault | At a road junction, engine started whilst in gear, resulting in vehicle entering the new road with potential risk to other road users. |
| Dangerous fault | Any situation brought about by a lack of ability to recognise the need to operate or being unable to operate the controls, which directly affects other traffic or pedestrians and causes actual danger. |
Ancillary controls
Expected outcome / competence
Ability to understand the function of all the controls and switches, especially those that have a bearing on road safety. These include indicators, lights, windscreen wipers, demisters and heaters. Ability to find these controls and operate them correctly, when necessary, without looking down or causing a loss of control.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Not completely familiar with the location and operation of controls, control of the vehicle was compromised but with no effect on road safety. |
| Serious fault | Unaware of location and operation of the controls resulting in a serious loss of vehicle control, road safety compromised. |
| Dangerous fault | Any situation brought about by the above fault that resulted in actual danger to the examiner, candidate, the general public or property. |
Move off
Safety / control
Expected outcome / competence
The ability to move off smoothly and safely, on a gradient and at an angle. Taking the correct precautionary observations.
Assessment criteria (example: safely)
| Type of fault | Example |
|---|---|
| Driving fault | Incorrect timing of the blind spot check when moving off with no risk to other road users. For e.g. checking the blind spot after the vehicle has moved off. |
| Serious fault | Moving off into the path of traffic or failing to take observation at all. |
| Dangerous fault | Any situation brought about by the above lack of observation that resulted in actual danger to the examiner, candidate, the general public or property. |
Use of mirrors – m/c rear observation
Expected outcome / competence
Full and effective use of all mirrors fitted to the vehicle. Mirrors must be checked carefully before signalling, changing direction or changing speed. Mirrors - Signal - Manoeuvre (MSM) routine should be displayed effectively.
Assessment criteria (example: change direction)
| Type of fault | Example |
|---|---|
| Driving fault | Late use of exterior mirror before changing direction. |
| Serious fault | Did not use the exterior mirror before a significant change in direction. |
| Dangerous fault | Any situation brought about by the above serious neglect of using the mirrors that resulted in actual danger to the examiner, candidate, and the general public or property. |
Signals
Necessary / correctly / timed
Expected outcome / competence
Signals should be given clearly to let other road users know the intended course to be taken. Signals shown in the Highway Code should only be used, if it would help other road users (including pedestrians). Signals should be given in good time and cancelled after the manoeuvre has been completed. Pedestrians should not be beckoned to cross the road.
Assessment criteria (example: signals necessary)
| Type of fault | Example |
|---|---|
| Driving fault | Signal applied but cancelled before the change in direction was complete. |
| Serious fault | Omitted an essential signal to inform other road users of a change in direction. |
| Dangerous fault | Any situation brought about by the above fault that resulted in actual danger to the examiner, candidate, the general public or property. |
Junctions (including roundabouts)
Including:
- approach speed
- observation
- turning right
- turning left
- cutting corners
Expected outcome / competence
Ability to judge the correct speed of approach so that the vehicle can enter a junction safely or stop if necessary. The vehicle should be positioned correctly, using the correct lane. When turning right, the vehicle should be positioned to the centre of the road as is safe. The vehicle should not cut the corner when turning right. When turning left, the vehicle should be over to the left to avoid swinging out. Watch out for cyclists and motorcyclists coming up on your left and pedestrians who are crossing. Effective observation must be given before moving into a junction and making sure it is safe before proceeding.
Assessment criteria (example: observation)
| Type of fault | Example |
|---|---|
| Driving fault | A misjudgement of the speed and distance of an approaching vehicle. Safety of other road users was not compromised. |
| Serious fault | Not taking effective observation before emerging at junctions, and emerging into the path of other vehicles. |
| Dangerous fault | Any situation brought about by the severe lack of effective observation that resulted in actual danger to the examiner, candidate, the general public or property. |
Judgement
Including:
- overtaking
- meeting
- crossing
Expected outcome / competence
Overtaking should only be carried out when it is safe to do so. A sufficient safety margin should be left when other vehicles are being overtaken. Cyclists and motorcyclists need as much space as other vehicles; they can wobble or swerve suddenly. Do not cut in too quickly after overtaking. Care should be taken when the width of the road is restricted or when the road narrows. If there is an obstruction on your side or not enough room for two vehicles to pass safely, the vehicle should be prepared to wait and let the approaching vehicles through. When turning right, other vehicles should not have to stop, slow down or swerve to allow the vehicle to complete its turn.
Assessment criteria (example: meeting)
| Type of fault | Example |
|---|---|
| Driving fault | Late reaction when meeting approaching vehicles. |
| Serious fault | Placing other drivers at risk by driving forward when they should have clearly given way. |
| Dangerous fault | Any situation brought about by the inability to meet approaching traffic that resulted in actual danger to the examiner, candidate, and the general public or property. |
Positioning
Normal driving / lane discipline
Expected outcome / competence
The vehicle should be positioned correctly for the intended route. Where lanes are marked, the vehicle should be positioned to the middle of the lane. Straddling lane markings should be avoided. Do not change lanes unnecessarily.
Assessment criteria - (example: normal driving)
| Type of fault | Example |
|---|---|
| Driving fault | Positioning errors when driving too close to the kerb. |
| Serious fault | Persistently driving too close to the kerb, placing pedestrians at risk. |
| Dangerous fault | Any situation brought about by driving dangerously close to the kerb that resulted in actual danger to the examiner, candidate, and the general public or property. |
Pedestrian crossings
Expected outcome / competence
The ability to recognise the different types of pedestrian crossings and show courtesy and consideration towards pedestrians. At all crossings, the vehicle should slow down and stop if there is anyone on the crossing. At zebra crossings, the vehicle should slow down and be prepared to stop if there is anyone waiting to cross. Ability to give way to any pedestrians on a pelican crossing when the amber lights are flashing. Ability to give way to cyclists as well as pedestrians on a toucan crossing and act correctly at puffin crossings.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Late to react to flashing amber at a ‘pelican’ crossing. |
| Serious fault | Failing to give way to pedestrians who had started to cross at a ‘pelican’ crossing. |
| Dangerous fault | Any situation brought about by the above fault that resulted in actual danger to the examiner, candidate, the general public or property. |
Position/normal stops
Expected outcome / competence
The ability to choose a safe, legal and convenient place to stop, close to the edge of the kerb, where the vehicle will not obstruct the road and create a hazard. Display an understanding of how and where to stop without causing danger to other road users.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Stopped, partially blocking a driveway with no inconvenience to other road users. |
| Serious fault | Stopped, completely blocking a driveway inconveniencing vehicle attempting to pull out. |
| Dangerous fault | Any situation brought about by the above fault that resulted in actual danger to the examiner, candidate, the general public or property. |
Awareness / planning
Expected outcome / competence
Display an awareness and consideration for other road users at all times. Ability to think and plan ahead, judging what other road users are going to do, predicting how their actions will affect the vehicle, and react in good time. Ability to consider the actions of the more vulnerable groups of road users such as pedestrians, cyclists, motorcyclists and horse riders. Anticipating road and traffic conditions, acting in good time, rather than reacting to them at the last moment.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Late reaction to what other road users are doing. |
| Serious fault | Last minute and sudden reaction to other road users compromising their safety. |
| Dangerous fault | Any situation brought about by the above fault that resulted in actual danger to the examiner, candidate, and the general public or property. |
Clearance – obstructions
Expected outcome / competence
Plenty of room should be allowed when passing stationary vehicles and obstructions. Ability to display the readiness to be prepared to slow down or stop, as a door may open, a child may run out, or a vehicle may pull out without warning.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Too close to a stationary vehicle when road conditions allowed the correct clearance. |
| Serious fault | Narrowly avoided a collision with a stationary vehicle when road conditions enabled the correct and safe course to be taken. |
| Dangerous fault | Any situation brought about by the above fault, due to passing dangerously close to, or striking a stationary vehicle, that resulted in actual danger to the examiner, candidate, the general public, or property. |
Following distance
Expected outcome / competence
The vehicle must always be a safe distance between yourself and other vehicles. On wet or slippery roads, it takes much longer to stop. When the vehicle has stopped in traffic queues, sufficient space should be left to pull out if the vehicle in front has problems.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Did not maintain the full separation distance required. |
| Serious fault | Drove too close to the vehicle ahead, where the separation distance left little margin for error. |
| Dangerous fault | Any situation brought about by dangerously driving too close to the car in front that resulted in actual danger to the examiner, candidate, and the general public or property. Action (ETA) should be taken as necessary to increase separation distance and so avoid the possibility of a collision. |
Use of speed
Expected outcome / competence
Safe and reasonable progress should be made along the road, bearing in mind the road, traffic and weather conditions, road signs, and speed limits. The vehicle should be able to stop safely, well within the distance you can see to be clear.
Assessment criteria (example)
| Type of fault | Example |
|---|---|
| Driving fault | Drove too fast for the prevailing road and/or traffic conditions for a short period. |
| Serious fault | Going too fast for the prevailing road and/or traffic conditions, exceeding speed limits. |
| Dangerous fault | Any situation brought about by driving far too fast that resulted in actual danger to the examiner, candidate, and the general public or property. Action (ETA) may be required to avoid a legal requirement being breached. Discretion must obviously be exercised in the degree to be considered acceptable, and the tolerance threshold over any speed limit must be quite small. |
Progress
Appropriate speed and undue hesitation
Expected outcome / competence
Candidates should drive at a safe and appropriate speed for the prevailing road and traffic conditions. Speed limits are not target speeds, and there will be occasions where candidates need to reduce their speed to deal safely with situations such as narrow residential streets or busy high streets; this should not be considered as a fault.
Assessment criteria (example: undue hesitation)
| Type of fault | Example |
|---|---|
| Driving fault | Lack of judgement, not proceeding when it is safe and correct to do so. |
| Serious fault | Stopping and waiting when it is safe and reasonable to proceed. |
| Dangerous fault | It is unlikely that undue hesitancy could become dangerous in itself unless it was felt that this created situations that encouraged other road users to put themselves at risk. |
Response to signs and signals
Traffic signs / road markings / traffic lights / traffic controllers / other road users
Expected outcome / competence
Ability to understand and be able to react to all traffic signs and road markings. Acting correctly at traffic lights, checking that the road is clear before proceeding when the green light shows. All signals should be obeyed given by police officers, traffic wardens, and school crossing patrols. Display the awareness to be able to react to signals given by other road users, including people in charge of animals, and be ready to act accordingly.
Assessment criteria (example: traffic lights)
| Type of fault | Example |
|---|---|
| Driving fault | Late reaction to an amber traffic light, with no effect on safety. |
| Serious fault | Failing to comply correctly and promptly with an appropriate traffic light or breaching a legal requirement. |
| Dangerous fault | Any situation brought about by the above breach of a legal requirement that resulted in actual danger to the examiner, candidate, the general public, or property. Action (ETA) may be required to avoid a legal requirement being breached. |
12. Finding and recording faults on the digital test report
12.01 Introduction
The information contained within this document is intended to be used as a guide to the location of fault markings on the Digital Test Report and to ensure uniformity. It is not intended as a guide to the assessment of faults. Driving Examiners of all grades were consulted and helped to prepare this document. It is not definitive and its content may be subject to alterations to reflect changing regulations and circumstances.
12.02 Location of faults
Having identified and assessed the fault it is important that the fault is recorded under the correct heading on the Digital Test Report. There are a number of faults that can occur during a driving test that initially may not appear appropriate to the relevant headings. To help with uniformity a ‘Guide to locating and recording of faults’ is provided.
The cause of the fault will normally determine the correct heading on the digital test report to mark it under.
Example of (Cause / Effect) - Stopping
CAUSE = (Clutch) Candidate attempts to pull up on the left at a safe and convenient place. The correct pressure is applied to the footbrake at the appropriate time. However, just before the vehicle stops, the clutch pedal was not pushed down to disengage the engine from the driving wheels causing the car to stall.
EFFECT = (Driving Fault) Because the clutch pedal was not pushed down to disengage the engine from the driving wheels the car stalled. As such, the control of the vehicle was compromised. Under the circumstances at the time, the correct assessment of this deviation from the defined outcome is a ‘driving fault’. Having identified the fault and assessed that it is worthy of recording, this should be recorded on the Digital Test Report.
If the effect is greater than the cause, then the effect is marked. For example, if a candidate approached a junction too fast and emerged - although the speed approaching the junction caused the fault, only the effect would be marked - junctions observation.
Eyesight
Read registration incorrectly for the fourth time using the tape.
Reverse right (Pull up on the right) or reverse left
(for all categories other than category B car tests)
For Category B car tests
(Begins when the candidate starts the MSM / PSL routine after being given the instructions)
Control
- poor co-ordination of controls
- scrubbing/brushing the kerb
- mounting the pavement
- stalling
- reversing out into the road
Observations
- no blind spot checks
- relying too much or entirely on the mirrors
- misjudging the speed and distance of oncoming vehicles
- misjudging the speed and distance of vehicles positioning to pass from behind
- no or late indication of intentions
- waiting unnecessarily for other road users
Reverse park
Recorded when reverse gear is selected.
Control
- poor co-ordination of controls
- scrubbing/brushing the kerb
- unnecessary shunting backwards and forwards
- getting too close to the object car
- mounting the pavement
- turning the steering wheel the wrong way
- parking too far from the kerb
- stalling
- not completing within two car lengths
- finishing at an acute angle to the kerb
Observation
- no blind spot checks
- relying too much or entirely on the mirrors
- ineffective observation
- looking but not reacting to other vehicles or pedestrians
- waiting too long for other users in the car park
Car park
- poor co-ordination of controls
- ending up straddling two bays
- unnecessary shunting forwards and backwards
- turning the steering wheel the wrong way
- stalling
Forward park
Car tests - (Recorded when instructions given to select a bay)
Control
- poor co-ordination of controls
- ending up straddling two bays
- unnecessary shunting forwards and backwards
- turning the steering wheel the wrong way
- stalling
Observation
- no blind spot checks
- relying too much or entirely on the mirrors
- ineffective observation
- looking but not reacting to other vehicles or pedestrians
- waiting too long for other users in the car park
Reverse (vocational / tractor and specialist vehicle tests) / with trailer
Recorded when reverse gear is selected.
Control
- poor co-ordination of controls
- stalling
- mounting the pavement or kerb
- turning the steering wheel the wrong way
- going wide after the corner
- finishing at an acute angle
- scrubbing-brushing-touching the kerb
- Ttking an excessive amount of time to complete the manoeuvre
Observation
- no blind spot checks
- no observation at or before the point of turn
- excessive use of the door mirrors
- not looking directly behind
- not reacting to passing or approaching vehicles
- not reacting to pedestrians
- waiting unnecessarily for other roads users
Uncouple/recouple (vocational +E tests only)
Highway code / safety
- incorrect answers to questions (Category F/G/H) / (Category D, D+E, D1)
Vehicle checks (‘Show me / Tell me’)
- 1 or 2 questions incorrect = 1 driving fault
- loss of control when demonstrating the on-road ‘show me’ question
Controlled stop
- late or slow reaction to the signal
- applying the handbrake before stopping
- skidding out of control
- missing the footbrake pedal
- letting go of the steering wheel
Control
Accelerator
- uncontrolled use
- excessive revs
Clutch
- not depressing the clutch pedal before stopping
- uncontrolled engagement after changing gear
Gears
- clutch coasting
- looking down when changing gear resulting loss of steering control
- selecting the wrong gear for the road and traffic conditions
Footbrake
- uncontrolled use resulting in pulling up too early or too late
- late or harsh braking
- missing the brake pedal completely
Handbrake
- applying whilst in motion
- not applying where necessary resulting in rolling forwards or backwards
- allowing the vehicle to ‘creep’ with an automatic
- unable to release fully
Steering
- unable to maintain a steady course in normal driving
- ‘swan neck’ turns when turning right
- at a normal stop, mounting and dismounting the kerb
- not following the contour of the kerb at a bell mouth junction
Precautions
- leaving in gear with the clutch up and starting the engine
Ancillary controls
- failure to use ancillary controls when necessary
- unable to operate controls
- not able to locate or operate essential ancillary controls
- loss of control whilst operating ancillary controls
Move off safety
- no blind spot checks / incorrectly timed checks moving away unsafely
- blind spot check only over the left shoulder for normal stops and angle starts
- following pull up on the right exercise – ineffective or no observations before moving off
- pulling away with the left signal on
Control
- stalling
- repeated stalling
- moving off with the handbrake applied
- rolling backwards when attempting to move off
- not engaging a gear and attempting to move off
- attempting to pull away in too high a gear
Use of mirrors (well before Signalling/Changing direction/Stopping)
- not using the exterior mirrors when essential
- using the mirrors but not reacting to the information
- not using the mirrors at all
- pulling up with no mirror checks
- increasing speed with no mirror checks
- late use of mirrors
Signals
Where necessary
- omitting to re-apply when it self-cancels
- omitting to give a signal where necessary
Correctly
- signalling unnecessarily
- wrong arm signals
- omitting to cancel after use
- incorrect (i.e. Left for right, right for left)
- flashing the headlights at another driver to proceed or turn
- having the hazard lights on whilst on the move
- unnecessary use of the horn
- beckoning pedestrians
Properly timed
- giving late exit signals at roundabouts
- arriving at a junction and then signalling
- signalling after starting the manoeuvre
- signalling far too early or too late
- misleading signal before intended left and right turn
Junctions
Approach speed
- approaching too fast
- approaching too slow
Observation
- not taking effective observation before emerging
- looking both ways but still emerging to affect other road users
Turning right
- positioning too far to the left
- positioning too far to the right
- on major to minor stopping short of the turning point
- incorrect position before turning right
Turning left
- positioning too far to the right or too close to the kerb
- swinging out prior to reaching the corner
- positioning in an unmarked inappropriate lane to turn left
Cutting corners
- cutting corners from major to minor roads
Judgement
Overtaking
- cutting in after overtaking
- attempting to overtake in a hazardous place
- unsafe overtaking
Meeting traffic
- failure to show proper judgement when meeting approaching traffic
Crossing traffic
- turning right across the path of oncoming road users
Positioning
Normal driving
- too close to the kerb
- too far from the kerb
- not using bus or cycle lanes when the times allow its use
- on dual carriageways driving in the right-hand lane
- cutting across the normal road position when going ahead at roundabouts
Lane discipline
- straddling marked lanes when going ahead
- straddling a bus lane
Pedestrian crossings
- approaching too fast
- not reacting to the lights at a pedestrian controlled crossing
- pulling away well before the crossing is clear of pedestrians
- not stopping when necessary
- beckoning pedestrians to cross
Position for normal stops
- normal stop not made in a safe position
- both nearside wheels on the kerb/pavement
- over a driveway
- at a bus stop
- too far from the kerb
- too near to a junction
- opposite other parked vehicles
Awareness and planning
- failure to judge what other road users are going to do and react accordingly
- not giving way to pedestrians clearly waiting to cross the road you are turning in or out of
Clearance to obstructions
- driving too close to stationary vehicles and obstructions
Following distance
- getting too close to moving vehicles
- pulling up too close to vehicle ahead
Use of speed
- driving too fast for prevailing road, traffic, and weather conditions
- breaking the speed limit
Progress
Appropriate speed
- not driving at an appropriate speed for the road and traffic conditions
- holding up following traffic
Avoiding undue hesitation
- stopping unnecessarily at junctions (except traffic light controlled junctions) and other hazards
- not proceeding when it is safe to do so at junctions
Response to signs and signals
Traffic signs
- going to the wrong side of a keep left sign
- non-compliance with a stop sign
- non-compliance with a No Entry sign
- driving in a Bus Lane when times on the sign prohibit its use
- not complying with Mandatory signs
Road markings
- unnecessarily crossing the solid white centre lines
- not conforming to directional arrows
- stopping in a yellow box junction when the exit is not clear
Traffic lights
- waiting at a green filter light when safe to proceed
- waiting to turn right in a junction, with red repeater light on opposite side and safe to proceed
- not conforming to a red light
- late reaction to the amber traffic light
- remaining at the stop line when safe to move forwards
- stopping beyond the solid white line going into an area designated for cyclists
Traffic controller
- police
- traffic warden
- school crossing patrol
- other persons directing traffic
Other road users
- not reacting appropriately to the signals given by other road users
13. Vehicle safety check questions
13.01 Safety check questions - cars
Tell me questions
T1: Tell me how you would check that the brakes are working before starting a journey.
A: Brakes should not feel spongy or slack. Brakes should be tested as you set off. Vehicle should not pull to one side.
T2: Tell me where you would find the information for the recommended tyre pressures for this car and how tyre pressures should be checked.
A: Manufacturer’s guide, use a reliable pressure gauge, check and adjust pressures when tyres are cold, don’t forget spare tyre, remember to refit valve caps.
T3: Tell me how you make sure your head restraint is correctly adjusted so it provides the best protection in the event of a crash.
A: The head restraint should be adjusted so the rigid part of the head restraint is at least as high as the eye or top of the ears, and as close to the back of the head as is comfortable. Note: Some restraints might not be adjustable.
T4: Tell me how you would check the tyres to ensure that they have sufficient tread depth and that their general condition is safe to use on the road.
A: No cuts and bulges, 1.6mm of tread depth across the central 3/4 of the breadth of the tyre and around the entire outer circumference.
T5: Tell me how you would check that the headlights & tail lights are working. (No need to exit vehicle)
A: Explanation: Operate switch (turn on ignition if necessary), then walk round vehicle. (As this is a “Tell Me” question, there is no need to physically check the lights).
T6: Tell me how you would know if there was a problem with your anti-lock braking system.
A: Warning light should illuminate if there is a fault with the anti-lock braking system.
T7: Tell me how you would check the direction indicators are working. (No need to exit the vehicle)
A: Explanation: Operate switch (turn on ignition if necessary), then walk round vehicle. (As this is a “Tell Me” question, there is no need to physically check the lights).
T8: Tell me how you would check the brake lights are working on this car.
A: Explanation: Operate brake pedal, make use of reflections in windows, garage doors, etc., or ask someone to help.
T9: Tell me how you would check the power assisted steering is working before starting a journey.
A: Explanation: If the steering becomes heavy, the system may not be working properly. Before starting a journey two simple checks can be made. Gentle pressure on the steering wheel, maintained while the engine is started, should result in a slight but noticeable movement as the system begins to operate. Alternatively turning the steering wheel just after moving off will give an immediate indication that the power assistance is functioning.
T10: Tell me how you would switch on the rear fog light(s) and explain when you would use it/them, (no need to exit vehicle).
A: Operate switch (turn on dipped headlights and ignition if necessary). Check warning light is on. Explain use.
T11: Tell me how you switch your headlight from dipped to main beam and explain how you would know the main beam is on.
A: Operate switch (with ignition or engine on if necessary), check with main beam warning light.
T12: Open the bonnet, identify, and tell me how you would check that the engine has sufficient oil.
A: Identify dipstick / oil level indicator, describe check of oil level against the minimum/ maximum markers.
T13: Open the bonnet, identify, and tell me how you would check that the engine has sufficient engine coolant.
A: Identify high/low level markings on header tank where fitted or radiator filler cap, and describe how to top up to correct level.
T14: Open the bonnet, identify, and tell me how you would check that you have a safe level of hydraulic brake fluid.
A: Identify reservoir, check level against high/low markings.
Show me questions
S1: When it is safe to do so can you show me how you wash and clean the rear windscreen.
S2: When it is safe to do so can you show me how you wash and clean the front windscreen.
S3: When it is safe to do so can you show me how you would switch on your dipped headlights.
S4: When it is safe to do so can you show me how you would set the rear demister.
S5: When it is safe to do so can you show me how you would operate the horn.
S6: When it is safe to do so can you show me how you would demist the front windscreen.
S7: When it is safe can you show me how you would open and close the side window.
13.02 Safety check questions - motorcycle
‘Show me / Tell me’ questions
Q1: Identify where you would check the engine oil level and tell me how you would check that the engine has sufficient oil.
A: Identify where to check level, i.e. dipstick or sight glass. Explain that level should be between max and min marks. For dipstick remove dipstick and wipe clean, return and remove again to check oil level against max/min marks. For sight glass, ensure glass is clean when checking.
Q2: Show me how you would check that the horn is working on this machine (off road only).
A: Check is carried out by using control (turn on ignition if necessary).
Q3: Identify where the brake fluid reservoir is and tell me how you would check that you have a safe level of hydraulic fluid.
A: Identify reservoir, check level against high/low markings.
Q4: Tell me how you would check that the lights and reflectors are clean and working.
A: Explanation only: Operate switch (turn on ignition if necessary), identify reflectors. Check visually for cleanliness and operation.
Q5: Show me how you would check that the brake lights are working.
A: Operate brake, place hand over light or make use of reflections in windows, garage doors, etc, or ask someone to help.
Q6: Tell me how you would check the condition of the chain on this machine.
A: Check for chain wear, correct tension and rear wheel alignment. Tension should be adjusted as specified in the machine handbook. Drive chain should be lubricated to ensure that excessive wear does not take place.
Q7: Show me what checks you would make on the steering movement before using the machine.
A: Handlebars should be free to move smoothly from full left lock to full right lock without any control cables being stretched, trapped or pinched and without any snagging between moving and fixed parts.
Q8: Tell me how you would check your tyres to ensure that they are correctly inflated, have sufficient tread depth and that their general condition is safe to use on the road.
A: Correct tyre pressure settings can be found in the owner’s manual. Pressures should be checked using a reliable gauge. Tread depth must be at least 1mm deep, forming a continuous band at least ¾ of the breadth of the tread and all the way around. There should be no lumps, bulges or tears.
Q9: Show me how you would check the operation of the front brake on this machine.
A: Wheel the machine forward and apply the front brake.
Q10: Show me how you would check the operation of the brakes on this machine.
A: Check for excessive travel on the brake lever and the brake pedal and for unusual play or sponginess.
Q11: Show me how you would check the operation of the engine cut out switch.
A: Operate switch, without the engine being started.
Q12: Show me how you would switch on the rear fog light and explain when you would use it (if fitted).
A Operate switch (turn on ignition and dipped headlights if necessary). Check warning light is on. Explain use.
Q13: Show me how you switch your headlight from dipped to main beam.
A: Operate switch (with ignition or engine on if necessary), check with main beam warning light.
Balance questions
What problems could arise from carrying a pillion passenger?
How should a passenger be carried on the pillion seat?
How would the balance of the machine be affected if you carried a pillion passenger?
13.03 Safety check questions - categories C and D
Q1: Show me how you would check that all doors including cargo doors are secure.
A: All doors must be closed and locking levers for cargo doors are set in the recommended secured position.
Q2: Show me how you would check for air leaks on this vehicle.
A: Charge the air tanks, consult gauges for drops in air pressure. Walk round vehicle listening for any obvious leaks.
Q3: Tell me the main safety factors involved in loading this vehicle.
A: The load should be evenly distributed throughout the length of the vehicle so as not to affect control while the vehicle is being driven. Any load must be carried so that it does not endanger other road users. It must be securely stowed within the size and weight limits for the vehicle. The load needs to be secure so that it cannot move or fall from the vehicle when cornering or braking.
Q4: Tell me how you would check the condition of the reflectors on this vehicle.
A: Ensure that all reflectors are fitted, clean, and functional (not cracked or broken).
Q5: Tell me how you would check the condition of the windscreen & windows on this vehicle.
A: The windscreen and windows must be clean, clear and free from defects. No mascots or sticker that restrict view.
Q6: Show me how you would check the condition of the mudguards on this vehicle.
A: As part of daily walk-round check ensure mudguards and spray suppression equipment are secure.
Q7: Tell me how you would check your tyres to ensure that they are correctly inflated, have sufficient tread depth and that their general condition is safe to use on the road.
A: Follow manufacturer’s guide, using appropriate equipment, check and adjust pressures when tyres are cold. Must have a tread depth of at least 1mm across three-quarters of the breadth of the tread and in a continuous band around the entire circumference. There should be no cuts, damage or signs of cord visible at the sidewalls.
Q8: Tell me how you would check the condition of the windscreen wipers on this vehicle.
A: Windscreen wipers must operate. Blades should be in good condition.
Q9: Tell me how you would check the condition of the body is safe on this vehicle.
A: As part of a daily walk-round check, ensure the body is fully roadworthy and there are no significant defects. No loose panels or items, which could endanger other road users. All inspection panels must be secure.
Q10: Show me how you would check for the correct air pressure on this vehicle.
A: Ensure gauges are reading the correct pressures for the vehicle and that all warning lights are extinguished and audible warning devices are not sounding.
Q11: Identify where you would check the engine oil level and tell me how you would check that the engine has sufficient oil.
A: Identify dipstick/ oil level indicator, describe check of oil level against the minimum/ maximum markers.
Q12: Show me how you would check the wheel nuts are secure on this vehicle.
A: A visual check to identify any nuts that are obviously loose, and check that the wheel nut indicators (if fitted) are in alignment.
Q13: Show me how you would check the operation (specify horn, warning device for reversing) of the audible warning devices on this vehicle.
A: Demonstrate use of control.
Q14: Tell me how you would check the condition of the suspension on this vehicle.
A: As part of a daily walk-round check, suspension should be checked for any obvious signs of deterioration or damage.
Q15: Show me how you would check that the brake lights are working on this vehicle (I can assist you, if you need to switch the ignition on, please don’t start the engine).
A: Operate brake pedal, make use of reflections in windows, garage doors, etc or ask someone to help.
Q16: Identify where you would check the engine coolant level and tell me how you would check that the engine has the correct level.
A: Identify high/low level markings on header tank where fitted or radiator filler cap, and describe how to top up to correct level.
Q17: Tell me how you would check that the headlamps, sidelights & tail lights are working.
A: Explain. Operate switch (turn on ignition if necessary), walk round vehicle.
Q18: Show me how you would replace the tachograph disc on this vehicle.
A: Candidate to demonstrate how to insert tachograph disc. Digital tachographs may require an explanation if the candidate does not have a digital card
Q19: Tell me how you would operate the loading mechanism on this vehicle (vehicle specific ie tail lift).
A: Candidates should be able to explain briefly the correct operation and safe working practice of specific machinery fitted to the vehicle, e.g. tail lift, kneeling bus.
Q20: Show me/ explain how you would check that the power assisted steering is working.
A: If the steering becomes heavy the system may not be working properly. Before starting a journey two simple checks can be made. Gentle pressure on the steering wheel, maintained while the engine is started, should result in a slight but noticeable movement as the system begins to operate. Alternatively turning the steering wheel just after moving off will give an immediate indication that the power assistance is functioning.
Q21: Show me how you would check that the direction indicators are working.
A: Applying the indicators or hazard warning switch and check functioning of all indicators.
Q22: Identify where the windscreen washer reservoir is and tell me how you would check the windscreen washer level.
A: Identify reservoir and explain how to check level.
Q23: Show me what instrument checks you would make before and after starting the engine on this vehicle.
A: Check to make sure all gauges and warning systems are working. Ensure that all gauges are reading correctly and that warning lights/ audible warning devices are extinguished before moving away.
Q24: Show me where the first aid equipment is kept on this vehicle.
A: Candidate to indicate equipment if carried. Where equipment is not present, candidates should be able to explain under what circumstances (i.e. vehicle types, loads carried) it must be provided.
Q25: Show me how you would clean the windscreen using the windscreen washer and wipers.
A: Operate control to wash and wipe windscreen (turn ignition on if necessary).
Q26: Show me how you would set the windscreen demister to clear the windows effectively
A: Set all relevant controls including; fan, temperature, air direction/ source and heated screen to clear windscreen and windows. Engine does not have to be started for this demonstration.
Q27: Show me how you would switch on the rear fog light(s) and explain when you would use it/them. (No need to exit vehicle)
A: Operate switch (turn on ignition and dipped headlights if necessary). Check warning light is on. Explain use.
Q28: Show me how you switch your headlight from dipped to main beam
A: Operate switch (with ignition or engine on if necessary), check with main beam warning light.
13.04 Safety check questions - categories C1+E, C+E, D1+E and D+E
Q1: Tell me how you would check the condition of the body is safe on this vehicle.
A: As part of a daily walk-round check, ensure the body is fully roadworthy and there are no significant defects. No loose panels or items, which could endanger other road users. All inspection panels must be secure.
Q2: Show me how you would replace the tachograph disc on this vehicle.
A: Candidate to demonstrate how to insert tachograph disc. Digital tachographs may require an explanation if the candidate does not have a digital card
Q3: Tell me how you would operate the loading mechanism on this vehicle (Vehicle specific. e.g. Tail Lift).
A: Candidates should be able to explain briefly the correct operation and safe working practice of specific machinery fitted to the vehicle, e.g. tail lift, kneeling bus
Q4: Show me how you would check that the wheel nuts are secure on this vehicle.
A: A visual check to identify any nuts that are obviously loose, and check that the wheel nut indicators (if fitted) are in alignment
Q5: Tell me how you would check the condition of the windscreen wipers on this vehicle.
A: Windscreen wipers must operate. Blades should be in good condition.
Q6: Show me how you would check that all doors including cargo doors are secure.
A: All doors must be closed and locking levers for cargo doors set in the recommended secured position.
Q7: Tell me how you would check the condition of the reflectors on this vehicle.
A: Ensure that all reflectors are fitted, clean, and functional (not cracked or broken)
Q8: Show me how you would check the condition of the mudguards on this vehicle.
A: As part of daily walk-round check ensure mudguards and spray suppression equipment are secure.
Q9: Tell me how you would check the condition of the suspension on this vehicle.
A: As part of a daily walk-round check, suspension should be checked for any obvious signs of deterioration or damage.
Q10: Show me what instrument checks you would make before and after starting the engine on this vehicle.
A: Check to make sure all gauges and warning systems are working. Ensure that all gauges are reading correctly and that warning lights / audible warning devices are extinguished before moving away.
Q11: Tell me the main safety factors involved in loading this vehicle.
A: The load should be evenly distributed throughout the length of the vehicle so as not to affect control while the vehicle is being driven. Any load must be carried so that it does not endanger other road users. It must be securely stowed within the size and weight limits for the vehicle. The load needs to be secure so that it cannot move or fall from the vehicle when cornering or braking.
Q12: Show me how you would check for air leaks on this vehicle.
A: Charge the air tanks, consult gauges for drops in air pressure. Walk round vehicle listening for any obvious leaks.
Q13: Show me how you would clean the windscreen using the windscreen washer and wipers.
A: Operate control to wash and wipe windscreen (turn ignition on if necessary).
Q14: Show me how you would set the windscreen demister to clear the windows effectively.
A: Set all relevant controls including; fan, temperature, air direction / source and heated screen to clear windscreen and windows. Engine does not have to be started for this demonstration
Q15: Show me how you would switch on the rear fog light(s) and explain when you would use it/them. (No need to exit vehicle)
A: Operate switch (turn on ignition and dipped headlights if necessary). Check warning light is on. Explain use.
Q16: Show me how you switch your headlight from dipped to main beam. (No need to exit vehicle)
A: Operate switch (with ignition or engine on if necessary), check with main beam warning light.
Q17: Show me how you would check that the brake lights are working on this vehicle. (I can assist you, if you need to switch the ignition on, please don’t start the engine)
A: Operate brake pedal, make use of reflections in windows, garage doors, etc or ask someone to help.
13.05 Safety check questions - tractor and specialist vehicle tests - categories F, G, H
‘Show me’ questions
S1: Show me how you would check that the direction indicators are working.
A: Applying the indicators or hazard warning switch and check functioning of all indicators. (may need to switch ignition on, prompt not to start engine).
S2: Show me how you would check the brake lights are working on this vehicle, (if you need to switch the ignition on, please don’t start the engine).
A: Operate brake pedal, make use of reflections in windows, garage doors, etc, or ask someone to help, (may need to switch ignition on, prompt not to start engine).
S3: Show me or explain how you would check that the power assisted steering is working before starting a journey.
A: If the steering becomes heavy the system may not be working properly. Before starting a journey two simple checks can be made. Gentle pressure on the steering wheel, maintained while the engine is started, should result in a slight but noticeable movement as the system begins to operate. Alternatively turning the steering wheel just after moving off will give an immediate indication that the power assistance is functioning.
S4: Show me how you would check the parking brake (handbrake) for excessive wear; make sure you keep safe control of the vehicle.
A: Apply footbrake firmly. Demonstrate by applying parking brake (handbrake) so that when it is fully applied it secures itself and is not at the end of the working travel.
S5: Show me how you would check that the horn is working.
A: Check is carried out by using control (turn on ignition if necessary).
S6: Show me how you would clean the windscreen using the windscreen washer and wipers.
A: Operate control to wash and wipe windscreen (turn ignition on if necessary).
S7: Show me how you would switch on the rear fog light(s) and explain when you would use it/them, (no need to exit vehicle).
A: Operate switch (turn on dipped headlights and ignition if necessary). Check warning light is on. Explain use.
S8: Show me how you switch your headlight from dipped to main beam and explain how you would know the main beam is on.
A: Operate switch (with ignition or engine on if necessary), check with main beam warning light.
S9: Show me how you would set the demister controls to clear all the windows effectively.
A: Set all relevant controls including fan, temperature air direction / source and heated screen to clear windscreen and windows. Engine does not have to be started for this demonstration.
S10: Open the bonnet, identify where you would check the engine oil level and tell me how you would check that the engine has sufficient oil.
A: Identify dipstick / oil level indicator, describe check of oil level against the minimum / maximum markers.
S11: Open the bonnet, identify where you would check the engine coolant level and tell me how you would check that the engine has the correct level.
A: Identify high/low level markings on header tank where fitted or radiator filler cap, and describe how to top up to correct level.
S12: Open the bonnet, identify where the brake fluid reservoir is and tell me how you would check that you have a safe level of hydraulic brake fluid.
A: Identify reservoir, check level against high/low markings.
‘Tell me’ questions
T1: Tell me how you would check that the brakes are working before starting a journey.
A: Brakes should not feel spongy or slack. Brakes should be tested as you set off. Vehicle should not pull to one side.
T2: Identify where the windscreen washer reservoir is and tell me how you would check the windscreen washer level.
A: Identify reservoir and explain how to check level.
T3: Tell me where you would find the information for the recommended tyre pressures for this vehicle and how tyre pressures should be checked.
A: Manufacturer’s guide, use a reliable pressure gauge, check and adjust pressures when tyres are cold, don’t forget spare tyre, remember to refit valve caps.
T4: Tell me how you would check your mirrors are secure and correctly adjusted to give you a clear view of the road behind.
A: Each mirror needs to be adjusted properly so it remains steady under normal driving conditions and gives a clear view of the road behind.
T5: Tell me how you would check that the headlights & taillights are working. (No need to exit vehicle)
A: Explanation: Operate switch (turn on ignition if necessary), then walk round vehicle. (As this is a “Tell Me” question, there is no need to physically check the lights).
T6: Tell me how you would check that the flashing amber beacon is working on this vehicle.
A: Operate the switch and check its operation.
Highway Code questions for tractor and specialist vehicle tests:
Q1: You are driving a slow-moving vehicle on an unrestricted dual carriageway. What must you use to warn other road users of your presence? (if necessary, add ‘if your vehicle was registered later than 1947)
A1: A flashing amber beacon. HC Rule 225
Q2: You are driving a slow-moving vehicle on a single carriageway. What should you do if another vehicle is trying to overtake you?
A2: Maintain a steady course and speed, slew down if necessary to the let the vehicle pass. Never obstruct drivers who wish to pass. Drop back to maintain a two-second gap if someone overtakes and pulls into the gap in front of you. HC Rule 168
Q3: You are driving a slow-moving vehicle on a single carriageway. What should you do if you a queue of traffic is building up behind?
A3: Do not hold up a long queue of traffic. Check your mirrors frequently, and if necessary, pull in where it is safe and let traffic pass. HC Rule 169
Q4: What action should you take when you overtake a horse and rider?
A4: Do not rev your engine, sound your horn or accelerate rapidly when you have
passed. Pass wide and slowly. Look out for horse riders and horse drivers signals and heed a request to slow down or stop. HC Rules 214 & 215
Q5: You have been driving off road on a muddy site. What should you do before driving your vehicle on the road?
A5: Ensure the tyres, tracks or rollers are clear of any mud or debris. Ensure windscreen, lights and number plate(s) are clean.
Q6: You are driving on a single-track road that’s only wide enough for one vehicle. What should you do when you see an oncoming vehicle?
A6: Pull into a passing place on your left or wait opposite a passing place on your right.
Give way to road users coming uphill whenever you can. If necessary, reverse until you reach a passing place to let the other vehicle pass. HC Rule 155
Q7: You have parked your vehicle on a public road. What must you do before leaving your vehicle unattended?
A7: Switch off the engine and apply the parking brake. HC Rule 123
Q8: You are crossing or turning right across a dual carriageway and the central reservation is too shallow for the full length of your vehicle. What action should you take?
A8: Wait until you can cross both carriageways in one go. HC Rule 173
Q9: As a driver, what must you consider when carrying a load on your vehicle to prevent danger to other road users?
A9: You must not overload your vehicle or trailer. You must secure your load and it must not stick out dangerously. Make sure any heavy or sharp objects and any animals are secured safely. You should properly distribute the weight. You may need to adjust the headlights. HC Rule 98
Q10: Driving when you are tired greatly increases your risk of collision. What should you do to minimise this risk?
A10: Do not begin a journey if you are tired. Get a good night’s sleep before driving. Avoid journeys between midnight and 6am when natural alertness is at its lowest. Take sufficient breaks (15 minutes for every 2 hours of driving). If you feel tired or sleepy, stop in a safe place. HC Rule 91
Q11: Your doctor has given you a course of medicine. Why should you ask whether it is safe for you to drive whilst taking the medicine?
A11: To make sure that the medicine will not make you drowsy or impair your ability to properly control your vehicle. You must not drive under the influence of drugs or medicine. HC Rule 96
Q12: What should you do before driving a vehicle you have never driven before?
A12: Make sure you know where all the controls are and how to use them. Make sure your mirrors, seat and head restraint are correctly adjusted. Ensure your vehicle is legal and roadworthy. HC Rule 97
Q13: You are approaching a set of traffic lights; the green light is showing. Which colour light will show next?
A13: Steady Amber. HC Light signals controlling traffic
Q14: As you approach a set of traffic lights, the green light changes to amber. What should you do?
A14: Stop at the stop line. You may go on only if the amber appears after you have crossed the stop line or are so close to it that to pull up might cause a collision or incident. HC Light signals controlling traffic
Q15: What shape are traffic signs which give warnings?
A15: Triangular. HC Traffic signs
Q16: There are double white lines along the centre of the road, the line nearest to you is solid. When may you cross this white line?
A16: If it is safe and you need to enter adjoining premises or a side road. You may cross the line, if necessary, provided the road is clear, to pass a stationary vehicle, or overtake a pedal cycle, horse or road maintenance vehicle, if they are travelling at 10 mph (16 km/h) or less. HC Rule 129
Q17: You are driving along a single carriageway and there is a broken white line along the centre of the road. What does it mean when the lines lengthen, and the gaps shorten?
A17: There is a hazard ahead. Do not cross the line unless you can see the road is clear and you wish to overtake or turn off. HC rule 127
Q18: What should you do if you wish to make or receive a phone call whilst you are driving?
A18: You must not use a handheld telephone. You must exercise proper control of your vehicle at all times. Find a safe place to stop first or use the voicemail facility and listen to messages later. HC Rule 149
Q19: You are driving a large, slow-moving vehicle and are about to drive over a level crossing. What should you do before crossing?
A19: Make sure it is safe to cross. Obey any signs or warning lights. Never drive onto the crossing until the road is clear on the other side and don’t get too close to the vehicle in front. You must obey any sign instructing you to use the railway telephone to obtain permission to cross. You must also telephone when clear of the crossing if requested to do so. HC Rules 291-299
Q20: You are driving a large or heavy vehicle. What should you consider when selecting your route?
A20: Vehicle height, width and weight restrictions. Whether your vehicle can pass safely under any low bridges you will encounter.
14. Test wordings
14.01 Test wordings for cars
Preliminaries
Good morning/afternoon Mr/Mrs/Miss/Ms ……. May I see your driving licence (and if required: also your TT pass certificate please).
Would you read and sign this insurance and residency declaration please?
Continue to email confirmation page.
Can you confirm your name is correct?
Is this the email you would like your test summary sent to?
There is a link to a survey in the email, we would appreciate your feedback.
Would you like your instructor/accompanying driver to accompany you on test? (This must be marked as accompanied on the app)
Note: Observer on Test wordings apply to Category ‘B’ tests only.
Thank you, lead the way to your car please.
In an effort to create a more relaxed and informal atmosphere during the test, examiners are encouraged to introduce themselves and use the candidate’s first name, provided there is no objection.
As self-introduction works best when it is spontaneous the examiner should decide whether to do it on the way to the car or wait until seated inside it. Examiners are encouraged to use a form of words that suits their own style and personality. The following example is for guidance only:
My name is…………. what would you prefer me to call you?
Pre-brief
A pre-test brief should be offered. This can be given during the walk to the car, or, if the distance is short, in the car. This should outline what will happen during the drive, for example:
Would you like me to explain about the test?
The test will include independent driving, various roads, and traffic conditions. I will ask you to complete one manoeuvre and we may carry out an emergency stop. The sort of things you have been practising with your instructor/accompanying driver.
Which car are you using?
Will you read the number of ………. car.
I would like to ask you two safety questions about your vehicle, the second question will be a show me question on the move, please make yourself comfortable in the car and I will join you in a moment.
Please do not start the engine.
General directions
Throughout the drive continue ahead, unless traffic signs direct you otherwise, When I want you to turn left or right, I will tell you in plenty of time. Move off when you are ready, please.
Drive on when you are ready, please.
Take the next road on the left/right, please.
Will you take the second road on the left/right, please. (If necessary, add this is the first.)
At the end of the road turn left/right, please.
At the roundabout turn left please (it is the first exit).
At the roundabout follow the road ahead (it is the second exit).
At the roundabout turn right please (it is the third exit).
(Additional information should be given if necessary to assist the driver to plan their route through the hazard. Examples are in brackets above).
Normal stops
Pull up on the left at a safe place, please
Designated/hill start
Pull up along here, just before………. please.
Controlled stop/angle start
Pull up on the left just before you get to the next parked car, please. (If necessary, add, leave enough room to move away.)
Independent drive section
Satnav directions
Now I would like you to drive independently, following the directions from the Satnav until I tell you otherwise. Please don’t rely on the speeds shown on the Satnav, as they may not be accurate. Drive on when you are ready.
Traffic signs
Pull up on the left please (either specify location or use normal stop wordings). Now I would like you to drive independently following the traffic signs for ……., continue to follow the signs until I tell you otherwise.
Drive on when you are ready.
Note: If using more than one destination sign, there is no need to pull up to change the destination.
Thank you, that’s the end of the independent driving. I will direct you from now on.
Emergency stop
Pull up on the left please (either specify location or use normal stop wordings) Shortly I shall ask you to carry out an emergency stop. When I give this signal, (simultaneously demonstrate, and say) ‘Stop,’ I’d like you to stop as quickly and as safely as possible. Before giving the signal, I shall look round to make sure it is safe, but please wait for my signal before doing the exercise.
Do you understand the instructions?
Thank you. I will not ask you to do that exercise again. Drive on when you are ready.
Reverse right
Pull up on the right when it is safe to do so, please.
I would now like you to reverse for about two car lengths, keeping reasonably close to the kerb.
Reverse parking
Would you pull up on the left well before you get to the next parked car, please. This is the reverse parking exercise (also known as parallel park). Would you drive forward and stop alongside the car ahead. Then reverse in and park reasonably close to and parallel with the kerb. Try to complete the exercise within about two car lengths.
Reverse Parking - car park
This can be carried out at the beginning or the end of the test.
Beginning of the test
Would you pull forward either to the left or the right so that your wheels are straight, then reverse into a convenient parking bay. Finish within one of the bays.
End of the test
I should like you to reverse park in the car park. Drive forward into the car park, then reverse into a convenient parking bay. Finish within one of the bays.
Forward Park
I would like you to drive forward into a convenient parking bay either to the left or the right (if car park allows), finish within one of the bays.
Now I would like to reverse out either to the left or the right. (Direct candidate if arrows indicate a one-way system in the car park).
Tractor and specialist vehicle tests categories F, G, H & K only
Please switch off the engine - now I should like to ask you a few questions on the Highway Code and other motoring matters and for you to identify some traffic signs for me.
End of the test pass
Please switch off the engine and give me a moment to complete my test report.
Would you like your instructor/accompanying driver to listen to the result and debrief?
Note: The debrief box should only be marked if the accompanying driver is present for the debrief.
That’s the end of the test and I’m pleased to say you’ve passed. Now that you will be driving on your own, I’d like you to be aware of/that…..Feedback as appropriate:
May I see your driving licence again please? Would you like your full licence sent to you automatically? If yes: I will need to keep your old licence and your new licence will be sent to the address on this licence, can you confirm that it is your correct address?
(If the candidate declines - inform them that the pass certificate only lasts for 2 years therefore they should apply for their full licence as soon as possible).
Please read the health declaration and sign in the box if you agree.
Here is your pass certificate - you should receive your new licence within about 20 working days. If you have any problems there are contact details on the back.
A copy of your test report will be sent to the email address that you provided at the start of the test.
As a new driver there are some very important details you need to know. Ask your instructor for details or visit the GOV.UK website.
Goodbye.
End of test fail
Please switch off the engine and give me a moment to complete my test report.
Would you like your instructor/accompanying driver to listen to the result and debrief?
Note: The debrief box should only be marked if the accompanying driver is present
for the debrief.
That’s the end of the test and I’m sorry you haven’t passed. To help you I’ll explain why.
Give feedback.
(The feedback should include all serious and dangerous faults. If the candidate fails on an accumulation of more than 15 driving faults only, then all the driving faults need explaining).
A copy of your test report will be sent to the email address that you provided at the start of the test.
(If ADI present) I’m sure your instructor will be able to help you further.
Goodbye.
14.02 Test wordings for motorcycles
Module 1
Preliminaries
The examiner should ask for the candidate by name, greet them pleasantly, and then:
Ask the candidate for and check their:
- driving licence, (and if not a photo licence, then a valid passport)
- theory test (TT) pass certificate
- CBT certificate (If applicable)
All three documents must be valid.
Mr/……. would you read, confirm and sign this insurance and residency declaration please?
(MUST check name and driver number on licence against information on declaration page.)
Can you please confirm this is the email address that you would like to receive your Riding Test Summary?
No;
Please enter your alternative email address or Please select your postal address
On module 1 there is no requirement to carry out an eyesight test or ask safety & balance questions.
The candidate should then be directed to the MMA (motorcycle manoeuvring area). At some casual sites the candidate may need to be fitted with a radio at this point.
General directions
Whilst on the motorcycle manoeuvring area, ride as if you are on the public road including carrying out any necessary safety checks and avoiding contact with any of the marker cones.
Please park your machine forwards in either of the two bays formed by the green marker cones and place it on the stand.
Manual handling
I would like you to take your machine off the stand and wheel it backwards out of this bay, then wheel it backwards into the bay formed by the green marker cones on your right/left and put your machine back on the stand.
Slow control steering
This is the slow control and steering exercise. Look at this diagram and I will explain what is required. At present you are here.
When I ask you, I would like you to ride between the yellow marker cones as this line shows. Begin by riding between the first and second marker cones. When you reach the two blue marker cones, ride in a figure of eight for two complete circuits. Don’t worry if you lose count. I will signal you to pull up close to where I will be standing when you have completed the exercise.
Start the exercise when you are ready.
Slow ride
I would like you to demonstrate your ability to ride as in slow moving traffic. When I ask you, move off and ride slowly in a straight line pulling up near the box formed by the blue marker cones ready for the U Turn exercise.
U Turn
This is the U Turn exercise. I would like you to ride your machine in a ‘U’ turn between the yellow/white lines, pulling up on the opposite side please. Remember to regard this as a public highway.
Start the exercise when you are ready.
Cornering and controlled stop
I would like you to ride a left / right circuit as the red line shows. Enter and leave the bend between the red and blue marker cones. You should aim to achieve a speed of about 30 to 50km/h (20 to 30mph) as you ride through the speed measuring device. Your speed will not be recorded for this exercise.
Once you have passed the speed measuring device brake to a normal stop, pulling up under full control with the front wheel within the area formed by the four blue marker cones.
If you look over there, you will see the stopping area formed by the blue marker cones.
Start the exercise when you are ready.
After the exercise the candidate should be asked to turn their machine around, taking as much space as necessary so they are in position to begin the next exercise. (Examiners should be ready to move the cones out of the way if this makes the turn more convenient, the first two cones should be stacked on the second two cones ready for the subsequent exercises.)
Cornering and emergency stop
Look at this diagram and I will explain what is required. At present you are here.
I would like you to ride a left / right circuit as this red line shows. Enter and leave the bend between the red and blue marker cones. As you go around the bend try and attain a minimum speed of 30kph (about 19mph). When you reach the speed measuring device, you are required to be travelling at a minimum speed of 50 kph, (About 32mph).
I will then give you a signal to stop, as in an emergency. The signal will be like this. (Demonstrate).
When I do that, stop as quickly and safely as possible, wherever you are on the area. (Examiners should position themselves near the stopping box area to give the emergency stop signal)
Have you any questions? Ride on when you are ready.
Thank you. I will not ask you to do that exercise again.
After the exercise the candidate should be asked to turn their machine around, taking as much space as necessary so they are in position to begin the next exercise.
Cornering and hazard avoidance
Look at this diagram and I will explain what is required. At present you are here.
I would like you to ride a left / right circuit, as this green line shows. Enter and leave the bend between the red and blue marker cones. As you go around the bend try and attain a minimum speed of 30kph (about 19mph). When you reach the speed measuring device, you are required to be travelling at a minimum speed of 50kph (about 32mph) before steering a course between the blue marker cones, coming to a controlled stop between the two blue marker cones.
If you look over there, you will see the avoidance and stopping area formed by the blue marker cones. Have you any questions?
Start the exercise when you are ready.
End of module 1 pass
Please switch off the engine and return to the test centre to complete the paper work.
(If accompanied by trainer) Would you like your (instructor/accompanying rider) to be present for the conclusion of the test? If the instructor / trainer /accompanying rider is not present the question should not be asked. If at any time the instructor/accompanying driver comes over to listen to the conclusion of the test, the examiner must ask the candidate whether they want their instructor/accompanying rider present.
The debrief box should be marked only if the accompanying rider is present for the feedback.
Complete digital test report.
That’s the end of the module 1 test and I am pleased to say you have passed. However there are some rider faults recorded and for your further development I will explain them to you. (Give debrief)
May I see your driving licence again please.
Complete module 1 pass certificate
Please read the health declaration and sign the bottom of the test report.
Issue module 1 pass certificate.
Here is your module 1 pass certificate. You have two years from the date you passed your theory and hazard perception test to pass module two of your motorcycle test (six months from the date of passing module 1 for riders upgrading an existing full motorcycle / moped licence). From 19 January 2013 there are some changes to the rules for new motorcyclists that may affect you, these are explained in the motorcycle section of the GOV.UK website.
You must present this module 1 pass certificate to the examiner when you take your module two test.
End of module 1 fail
Please switch off the engine and return to the test centre to complete the test report. (If accompanied on test) Would you like your (instructor/accompanying rider) to be present for the conclusion of the test? If the instructor / trainer /accompanying rider is not present the question should not be asked.
(If at any time the instructor/accompanying rider comes over to the machine to listen to the conclusion of the test, the examiner must ask the candidate whether they want their instructor/accompanying rider present)
That’s the end of the module 1 test and I’m sorry you haven’t passed. To help you I will explain why?
Would you like your (instructor/accompanying rider) to be present for the de-brief.
If requested give de-brief and mark the de-brief box if the accompanying rider was present. The de-brief should include all serious and dangerous faults. If the candidate fails on an accumulation of more than 5 riding faults only, then all the riding faults need explaining.
Module 2
Preliminaries
The examiner should ask for the candidate by name, greet them pleasantly, and then:
Ask the candidate for their:
- driving licence, (and if not a photo licence, then a valid passport)
- theory test (TT) pass certificate and
- CBT certificate (If applicable)
- module 1 pass certificate
All four documents must be valid. Once checked all documents must be returned to the candidate.
Is your name and address still the same as on your driving licence? (Examiner: you will need to be aware of this and can confirm during the end of test procedure).
Mr/……. would you read, confirm and sign this insurance and residency declaration please?
(MUST check name and driver number on licence against information on declaration page.)
Can you please confirm this is the email address that you would like to receive your Driving Test Summary?
No
Please enter your alternative email address
or
Please select your postal address
Pre-brief
I would now like to fit the radio so that you can hear my directions during the test.
My directions will be brief and simple, for example at the end of the road, turn right. If we get separated, such as at traffic lights, it may be necessary for me to ask you to pull up on the left at a convenient place and wait until I rejoin you.
The test will last about 38-40 minutes and it will take in various roads and traffic conditions. I will be asking you to ride for a short section of the test independently before this section I will pull you up and explain what I want you to do.
Will you lead the way to your bike, please?
Which is your bike,?
Will you read the number of … car.
Walk towards your bike. To check the radio I will give you a direction and if you hear it, raise your arm, please.
The candidate should be asked 2 machine safety check questions and the balance question before moving away. To ensure uniformity the safety questions must be selected from the bank of questions listed at annex 2.
General directions
Throughout the test continue ahead, unless traffic signs direct you otherwise, and when I want you to turn left or right I will tell you in plenty of time. You may start the engine but please wait for my radio instruction before you move away.
(A further confirmation that the candidate can hear the instructions correctly should be made shortly after leaving the test centre.)
Normal stops, Angle start, Hill start; as per the car wordings.
Independent Ride Section
Verbal directions
Pull up on the left please (either specify location or use normal stop wordings) Shortly, I’d like you to ride for some distance independently.
I’d like you to follow a series of directions. Would you like to see a diagram? The directions are ……………………………………. e.g. At the end of the road turn right, at the roundabout follow the road ahead and then take the next road on the left.
Can you repeat those back to me please. (So, that you know candidate has understood the directions) Thank you. Ride on when you are ready.
Traffic signs
Pull up on the left please (either specify location or at a convenient place).
Shortly, I’d like you to ride for some distance independently.
I’d like you to follow the traffic signs for ……………………………please. Continue to follow the signs until I tell you otherwise. ‘As per route advice’ .
If we get separated, I will ask you to pull up on the left until I can re-join you .
Ride on when you are ready.
If using more than one destination sign, there is no need to pull up to change the destination
Thank you, that’s the end of the independent driving. I will direct you as normal from now on.
Candidates should be advised that if they are having difficulty following directions in the independent section they should pull up in a safe convenient position and wait for the examiner to confirm route.
End of module 2 test pass
Please switch off the engine and return to the test centre to complete the report.
(If accompanied by trainer) Would you like your (instructor/accompanying rider) to be present for the conclusion of the test?
If the instructor / trainer /accompanying rider is not present the question should not be asked. If at any time the instructor/accompanying driver comes over to listen to the conclusion of the test, the examiner must ask the candidate whether they want their instructor/accompanying rider present. The de-brief box should be marked only if the accompanying rider is present for the feedback.
Complete Digital Test Report.
That’s the end of the test and I am pleased to say that you have passed - you can now (none DAS - continue to) ride unaccompanied whilst you gain experience. However there are some rider faults recorded and for your further development I will explain them to you. (Give de-brief)
With regard to eco-safe riding (if appropriate) I have noted…..
May I see your driving licence again please? Can you confirm this is your correct address. (If candidate unsure in any way select ‘Licence Received NO’ and return licence to candidate).
(If address confirmed) Would you like your full licence sent to you automatically? Do you need your licence for ID or any other purpose as I will need to keep your old licence and once it is submitted this cannot be reversed. (If candidate unsure in any way select ‘Licence Received NO’ and return licence to candidate).
(Once confident that the licence can be received, select ‘Licence Received YES’ take the licence and process back in the office)
(If the candidate declines - inform them that the pass certificate only lasts for 2 years therefore they should apply for their full licence as soon as possible).
Please read, confirm and sign the health declaration and that you have received a copy of your pass certificate.
(if candidate does not confirm health declaration, give licence back and app will automatically select ‘Licence Received NO’).
Here is your pass certificate - you should receive your new licence within about 20 working days. If you have any problems, there are contact details on the back.
Your test summary will be sent to you shortly.
To help keep you safe talk to your instructor about the Enhanced Rider Scheme, which is designed to help you improve your riding skills and enjoy your biking safely.
There are some very important details about the restrictions that relate to your licence that you need to be aware of before you (continue to) ride unaccompanied. Please take the time to visit the GOV.UK website for details.
Ask your instructor for details.
End of module 2 test fail
Please switch off the engine and return to the test centre to complete the test report.
(If accompanied by trainer) Would you like your (instructor/accompanying rider) to be present for the conclusion of the test?
If the instructor / trainer /accompanying rider is not present the question should not be asked. If at any time the instructor/accompanying driver comes over to listen to the conclusion of the test, the examiner must ask the candidate whether they want their instructor/accompanying rider present
The de-brief box should be marked only if the accompanying rider is present for the feedback.
Complete Digital Test Report.
That’s the end of the test and I’m sorry you haven’t passed.
To help you I will explain why
Would you like your (instructor/accompanying rider) to be present for the De-brief? If requested give de-brief and mark de-brief box if the accompanying rider was present. The de-brief should include all serious and dangerous faults. If the candidate fails on an accumulation of more than 10 riding faults only, then all the riding faults need explaining.
In all cases an Eco-safe riding de-brief should be given as follows:
With regard to Eco-safe riding I have noted… (appropriate de-brief)
You will receive your end of test summary shortly.
14.03 Test wordings for - LGV/PCV and B + E
Module 3a
Preliminaries
As per the car test.
Pre-brief
Reversing exercise for category ‘C, CE, C1, C1E’
I’d like you to carry out the reversing exercise. If you will look at this diagram, I will explain what is required.
At present you are here. When I ask you, drive forward and stop with the extreme front of your vehicle level with and between the two cones shown here as A and A1. They are the ones beyond the one with the pole. Then reverse, as the arrowed line shows, keeping the cone with the pole on your offside. Reverse into the bay and stop with the extreme rear of your vehicle in the yellow and black-hatched area, so that you are parked safely for loading or unloading. If you look to your left you will see the bay and the yellow and black chevron stopping area. Do not drive further forward than cones A & A1 at any time and try not to touch any of the marker cones or cross the yellow boundary lines.
Do you understand that? Please wait for my signal before you start the exercise.
Note: Cones A and A1 should not be removed or re-positioned before the candidate has completed the reverse manoeuvre.
Reversing exercise for category ‘D, DE, D1, D1E’
I’d like you to carry out the reversing exercise. If you will look at this diagram, I will explain what is required.
At present you are here. When I ask you, drive forward and stop with the extreme front of your vehicle level with and between the two cones shown here as A and A1. They are the ones beyond the one with the pole. Then reverse, as the arrowed line shows, keeping the cone with the pole on your offside. Enter the bay and finish with the extreme rear of your vehicle within the yellow and yellow & black chevron stopping area. If you look to your left, you will see the bay and the yellow stopping area. Do not drive further forward than cones A & A1 at any time and try not to touch any of the marker cones or cross the yellow boundary lines.
Do you understand that? Please wait for my signal before you start the exercise.
Vehicles drawing trailers
Park in a convenient place (usually at the end of the area away from the reversing box) then:
I’d like you to uncouple the trailer, drive the towing vehicle forward, then park it either to the left or the right of the trailer.
I’d like you to re-couple the trailer assuming it is a different one to the one you uncoupled and make it safe for the road. When you’ve finished return to the cab.
End of test pass
Please switch off the engine and give me a moment to complete my report. (If the test was not accompanied and the instructor/accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner should confirm with the candidate they want their instructor/accompanying driver present)
That’s the end of the test and I’m pleased to say you’ve passed. I’d like you to be aware of/that…..Feedback as appropriate:
(If instructor present) I’m really pleased your instructor is here. And I’m sure he/she will be able to help you further.
May I see your driving licence again please?
Here is your pass certificate, it lasts for 6 months, you will need to produce it to the examiner at the time of the 3b on road test, without the 3a certificate you will be unable to take your 3b on road test.
Please read, confirm, and sign the health declaration and that you have received a copy of your pass certificate.
You will receive your end of test summary shortly. (DVSA DTR only)
Goodbye
End of test fail
Please switch off the engine and give me a moment to complete my report.
(If the test was not accompanied and the instructor/accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner should confirm with the candidate they want their instructor/accompanying driver present)
Note: The de-brief box should only be marked if the accompanying driver is present for the de-brief .
That’s the end of the test and I’m sorry you haven’t passed.
To help you I’ll explain why. Give feedback.
(If instructor present) I’m really pleased your instructor is here. And I’m sure he/she will be able to help you further.
You will receive your end of test summary shortly. (DVSA DTR only)
Module 3b
Note: External Assessors will only issue a statement of failure at the end of Module 3a.
Preliminaries
As per the car test.
Is your load secure? (Except categories C1, D1 & D)
(When entering the vehicle for the first time and if the vehicle has a tilt cab:) Is the tilt cab is locked down?
All vehicles
Vehicle safety check questions
Category ‘C’ and ‘D’
I should like to ask a few questions relating to the safe operation of this vehicle.
Or
Now I should like to ask you a few questions about your vehicle and other matters relating to vehicle safety.
Vehicles drawing trailers
Now I should like to ask 2 questions relating to appropriate safety checks you should routinely make before starting a journey.
Invite candidate to wear safety equipment.
(If entering the vehicle for the first time and the vehicle has a tilt cab:) Is the tilt cab is locked down?
General directions
General route and other directions/instructions should be as per the car test. Additionally:
LGV Tests - Obey all ‘Weight Restrictions’ unless I specifically tell you otherwise. (Only mention if weight restriction/s are on the route being used)
PCV Tests - You would be expected to use bus lanes as appropriate. (Only mention if bus lane/s are on the route being used)
End of test pass
Please switch off the engine and give me a moment to complete my report. (If the test was not accompanied and the instructor/accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner should confirm with the candidate they want their instructor/accompanying driver present)
That’s the end of the test and I’m pleased to say you’ve passed. Now that you will be driving on your own, I’d like you to be aware of/that….Feedback as appropriate:
(If instructor present) I’m really pleased your instructor is here. And I’m sure he/she will be able to help you further.
May I see your driving licence again please? Would you like your full licence sent to you automatically? If yes: I will need to keep your old licence and your new licence will be sent to the address on this licence, can you confirm that it is your correct address?
(If the candidate declines - inform them that the pass certificate only lasts for 2 years therefore they should apply for their full licence as soon as possible).
Please read the health declaration and sign in the box if you agree.
Here is your pass certificate - you should receive your new licence within about 20 working days. If you have any problems, there are contact details on the back.
A copy of your test report will be sent to the email address that you provided at the start of the test.
As a new driver there are some very important details you need to know. Ask your instructor for details Please take the time to visit the GOV.UK website.
Please take time to discuss eco-safe driving with your instructor and learn how you can save money.
Goodbye
End of test fail
Please switch off the engine and give me a moment to complete my report.
(If the test was not accompanied and the instructor/accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner should confirm with the candidate they want their instructor/accompanying driver present)
Note: The de-brief box should only be marked if the accompanying driver is present for the de-brief.
That’s the end of the test and I’m sorry you haven’t passed.
To help you I’ll explain why.
Give feedback. (The feedback should include all serious and dangerous faults. If the candidate fails on an accumulation of more than 12 driving faults only, then all the driving faults need explaining).
A copy of your test report will be sent to the email address that you provided at the start of the test.
(If instructor present) I’m really pleased your instructor is here. And I’m sure he/she will be able to help you further. Eco feedback
Please take time to discuss eco-safe driving with your instructor and learn how you can save money.
Goodbye
As part of the test conclusion, examiners should also ask any survey questions in line with latest instructions
Note: The test wordings as outlined above, can be used concurrently for delegated authorities who are still conducting the LGV, PCV test as one event.
14.04 Test wordings for CPC practical safety demonstration test
Preliminaries
Good morning/afternoon Mr/Mrs/Miss/Ms…………May I see your driving licence and your photo ID please.
…………..would you read and sign this insurance and residency declaration please?
Can you please confirm this is the email address that you would like to receive your Driving Test Summary?
No -
Please enter your alternative email address.
or
Please select your postal address.
Thank you, will you lead the way to your vehicle please.
In an effort to create a more relaxed and informal atmosphere during the test, examiners are encouraged to introduce themselves and use the candidate’s first name, provided there is no objection.
As self-introduction works best when it is spontaneous the examiner should decide whether to do it on the way to the vehicle, or wait until reaching the vehicle.
Pre-brief
This is the Practical Safety Demonstration Test. Would you like me to give you a brief overview of the test?
If the candidate says yes then a ‘brief’ explanation can be given e.g. ‘the test will last about 30 minutes and when we get to the vehicle I will ask you 5 questions on set topics. I would like to emphasise that this is a demonstration type test, therefore when I ask you questions I will be looking for you to show your knowledge and understanding.’
At the vehicle
Now I should like to ask you some questions relating to your vehicle; remember, it is important that you demonstrate your responses, and not just tell me what you would do.
End of test pass
Please give me a few moments to complete my report
If the instructor/trainer/accompanying driver is present ask: would you like your (instructor/accompanying driver) to be present for the conclusion of the test? If the instructor/trainer/accompanying driver is not present the question should not be asked. If at any time the instructor/accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner must ask the candidate whether they want their instructor/accompanying driver present.
That’s the end of the test and I’m pleased to tell you that you’ve passed, well done. May I see your driving licence again please?
Complete the DVSA11(Copy the driver number from the licence onto the DVSA11). Enter the DVSA11 number onto the Digital Test Report
Here is your pass certificate, when you have passed all Modules of Driver CPC you will be sent your Driver Qualification Card (DQC) automatically. You will receive your end of test summary shortly If requested give de-brief and mark the de-brief box, just offer a factual overview of the candidate’s performance.
Thank you and congratulations. Goodbye.
Note: Module 4is not a licence acquisition test. Therefore, the candidate’s licence must not be taken from them under any circumstances. If a licence were to be shredded the candidate would have to apply for a replacement licence.
End of test fail
Please give me a few moments to complete my report
If the instructor/ trainer/ accompanying driver is present, ask: would you like your (instructor/ accompanying driver) to be present for the conclusion of the test? If the instructor/trainer/accompanying driver is not present the question should not be asked. If at any time the instructor/ accompanying driver comes over to the vehicle to listen to the conclusion of the test, the examiner must ask the candidate whether they want their instructor/accompanying driver present.
That’s the end of the test and I’m sorry you haven’t passed. Would you like me to explain why?
Offer the candidate a brief overview of the topic area(s) that they did not answer correctly. It is most important that you avoid giving the candidate specific details of the KKI’s that they did not answer correctly. To encourage the candidate to study before a re-test, make reference in the de-brief to the Official DVSA Guide range of learning resource materials.
You will receive your end of test summary shortly.
Thank you. Goodbye.
15. Flowchart for automatic upgrade
